Honda SHUTTLE Keyfob RKE Programming

HOW TO GUIDE: Honda Shuttle RKE Keyfob Programming

by

Honda Shuttle RKE Keyfob Programming

A tutorial on how to program a Honda Shuttle Keyfob remote keyless entry RKE from 1994 to 1999. Please follow the Compilation of Keyfob Programming for Honda Shuttle below.

Honda Shuttle RKE Programming Procedure 1

  1.  Open the drivers door.
  2.  Push the drivers power door lock switch to the unlock position and hold it. ( Continue to hold the switch during this procedure.)
  3.  Insert the key into the ignition, then remove it. Repeat this 4 more times within 10 seconds. ( You must complete steps 3 and 4 within 10 seconds or the system will exit the programming mode.
  4.  Insert the key into the ignition. After you insert the key, make sure the power door locks cycle to confirm that the system is in the programming mode.
  5.  Press the LOCK and UNLOCK button on the remote. All power door locks ( except the drivers door ) should cycle to confirm that the system accepted the remote.
  6.  To program a second remote, press the LOCK and UNLOCK button within 10 seconds of programming the first remote. ( The system will only accept two remotes.
  7.  Release the master power door lock switch to exit the programming mode.
  8.  Test remotes.

Honda Shuttle keyfob Programming Procedure 2

Programming Notes:

Obtain all remote transmitters for this vehicle. This procedure will erase all previously programmed remotes. You must program all existing and new remotes that you wish to use on the vehicle at this time.

Procedure #1 – Factory Installed Keyless Entry Systems (Most Common)

Step-by-Step How To Programming Instructions:

  1. OPEN Driver’s door.
  2. PRESS and HOLD the UNLOCK switch on the Driver’s door and continue to HOLD until instructed to release.
  3. Within 10 seconds, INSERT the key into the ignition and REMOVE it five (5) times.
  4. INSERT the key a sixth (6) time and leave it in the Ignition. The vehicle will respond by cycling the locks indicating entry into Programming Mode.
  5. PRESS the LOCK OR UNLOCK Button on the remote. The vehicle will respond by cycling the locks indicating successful programming of the remote.
  6. REPEAT Step 5 within 10 seconds for each additional remote to be programmed.
  7. RELEASE the UNLOCK Button on the Driver’s door to exit Programming Mode.
  8. Test all remotes. Programming is now complete.
  9. If these programming instructions helped you save time and money, please consider sharing our website with friends and family so they can do the same.

Honda Shuttle RKE keyfob Programming Procedure 3

  1.  Turn ignition switch to ON (II)
  2.  Within 4 seconds press the LOCK or UNLOCK button on one of the remotes. Make sure remote is aimed at the receiver near the glove box.
  3.  Within 4 seconds turn ignition switch to LOCK (0)
  4.  Repeat steps 1, 2 and 3 two more times using the same keyless remote used in step 2
  5.  Within 4 seconds turn the ignition switch to ON (II)
  6.  Within 4 seconds press the LOCK or UNLOCK button the same remote. Make sure the power door locks cycle to confirm you are in programming mode. Press the LOCK or UNLOCK button again.
  7.  Press the LOCK or UNLOCK button on each remote you want to program. Make sure door locks cycle after you push each remote button to confirm system has accepted the remote.
  8.  Turn the ignition switch to LOCK (0) to exit programming mode.
  9.  Test remote(s)

Honda Shuttle RKE keyfob Programming Procedure 4

  1.  Turn ignition switch to ON (II)
  2.  Within 4 seconds press the LOCK or UNLOCK button on one of the remotes. Make sure remote is aimed at the receiver near the glove box.
  3.  Within 4 seconds turn ignition switch to LOCK (0)
  4.  Repeat steps 1, 2 and 3 two more times using the same keyless remote used in step 2
  5.  Within 4 seconds turn the ignition switch to ON (II)
  6.  Within 4 seconds press the LOCK or UNLOCK button the same remote. Make sure the power door locks cycle to confirm you are in programming mode. Press the LOCK or UNLOCK button again.
  7.  Press the LOCK or UNLOCK button on each remote you want to program. Make sure door locks cycle after you push each remote button to confirm system has accepted the remote.
  8.  Turn the ignition switch to LOCK (0) to exit programming mode.
  9.  Test remote(s)

Thank you very much! This tutorial was compiled and researched with ❤️ by Erwin Salarda.