Toyota RAV4 Keyfob RKE Programming

HOW TO GUIDE: Toyota RAV4 RKE Keyfob Programming

by

Toyota RAV4 RKE Keyfob Programming

This is a step-by-step guide for programming the RKE Keyfob on the Toyota RAV4 from 1996 to 1997, 1998 to 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019 to 2020.

 

Toyota RAV4 1996-2000 RKE keyfob Programming

  1. Locate ECU Programming Receiver

    LOCATE the ECU Programming Receiver.
    rke

  2. Insert Key into Ignition

    INSERT key into Ignition and TURN to the ON position.

  3. Enter Programming Mode

    PRESS and HOLD the ECU’s Programming Switch for 3 seconds using a paperclip or small screwdriver. The Status Monitor LED light will turn on for 5 seconds to indicate successful entry into Programming Mode..

  4. Program Remote

    WITHIN 5 seconds, PRESS and RELEASE ANY button on the remote. The Status Monitor LED light will turn OFF, the piezo chirper will chirp ONCE and the exterior lights will flash ONCE to indicate successful programming of the remote. IF you hold the button too long and the vehicle alarm sounds, simply press the TOP button on the remote to reset the alarm.

  5. EXIT Programming Mode

    TURN OFF the Ignition to EXIT Programming Mode.

  6. Test Remotes

    TEST all remotes. Programming is complete.

<>

Programming Notes:

  • Verify the following prior to following these instructions:
    • Your vehicle is equipped with keyless entry, and
    • You have a key fob remote that is compatible with your vehicle.
  • Obtain ALL remote transmitters for this vehicle.
  • Important: For MOST vehicles, the ECU Programming Receiver is located UNDERNEATH either the Driver or Passenger front seats. For SOME vehicles, it is located BEHIND the Driver’s Dash and can be accessed by prying out the black faceplate (5”x3”) BEHIND the mirror control switch. It is a BLACK box with 3 connectors and a recessed GREEN RESET button. Refer to the Owner’s Manual for your vehicle’s ECU location.

Toyota RAV4 2001-2020 RKE keyfob Programming

  1. Prepare Vehicle

    With the key OUT of the Ignition, OPEN and UNLOCK the Driver’s door.

  2. Enter Programming Mode – Step 1

    Perform the following steps within 5 seconds:

    a. INSERT key into Ignition (Do NOT turn) and PULL the key out.

    b. INSERT key into Ignition (Do NOT turn) and PULL the key out.

  3. Enter Programming Mode – Step 2

    PERFORM the following steps WITHIN 40 seconds:

    a. CLOSE then OPEN Driver’s door.

    b. CLOSE then OPEN Driver’s door.

    c. INSERT key into Ignition (Do NOT turn) and PULL the key out.

  4. Enter Programming Mode – Step 3

    PERFORM the following steps WITHIN 40 seconds:

    a. CLOSE then OPEN Driver’s door.

    b. CLOSE then OPEN Driver’s door.

    c. INSERT the key into the Ignition and LEAVE it in the Ignition.

    d. CLOSE the Driver’s door.

  5. Enter Programming Mode – Step 4

    TURN the Ignition to ON position (Do NOT crank engine) then back OFF.
    – Do this ONCE to retain existing remotes programmed and ADD NEW remote..
    – Do this TWICE to ERASE all existing remotes programmed and ADD NEW remote.
    – Do this THREE times to CHECK how many remotes are programmed to the vehicle.
    – Do this FIVE times to ERASE all existing remotes programmed.

  6. Enter Programming Mode – Step 6

    REMOVE key from Ignition. The power door locks will respond by cycling the locks from LOCK/UNLOCK to signal successful entry into Programming Mode.

  7. Program Remote

    Perform the following steps within 40 seconds:

    a. PRESS and HOLD the LOCK and UNLOCK buttons on the remote simultaneously for 2 seconds. RELEASE.

    b. PRESS and HOLD the LOCK button and hold for 2 seconds. RELEASE.

    The vehicle will respond by cycling the locks from LOCK to UNLOCK to indicate successful programming of the remote.

  8. Program Additional Remotes

    REPEAT Step 7 for any additional remotes to be programmed, including working ones.

  9. EXIT Programming Mode

    OPEN Driver’s Door to EXIT Programming Mode.

  10. Test Remotes

    TEST all remotes. Programming is complete.

<>

Programming Notes:

  • Verify the following prior to following these instructions:
    • Your vehicle is equipped with keyless entry, and
    • You have a key fob remote that is compatible with your vehicle.
  • Obtain ALL remote transmitters for this vehicle.
  • If you have a remote head key with a transponder chip, this procedure will ONLY program the remote portion. You’ll need a Professional Auto Locksmith to cut and program the transponder key that will start the vehicle.
  • If you have a remote head key without a transponder chip, this procedure WILL work for your vehicle.
  • This procedure DOES NOT work for smart proximity remote key fobs.