How to: Ford E-Series 2007-2016 TPMS Reset / Relearn

Ford E-Series TPMS Reset

FORD E-SERIES TPMS RESET

How to reset and relearn the TPMS of Ford E-Series Model from year 2007-2008-2009-2010-2011-2012-2013-2014-2015-2016.

About Ford E-Series

The Ford E series (also known as the Ford Econoline and Ford Club Wagon throughout various stages of its production) is a range of full-size vans produced by the American automaker Ford since 1960. Introduced for the 1961 model year as the replacement for the Ford F-series panel van, four generations of the model line have been produced. In addition to cargo van and passenger van body styles, the Ford E-series has been produced as a cutaway van chassis and stripped chassis (a chassis without bodywork).

From 1980 to its 2015 discontinuation, the E-series van was the best-selling full-size van in the United States, holding a nearly 80% share of the segment. At the time of its final redesign, 95% of sales were to commercial or fleet users, with nearly half of production represented by cargo vans. For the 2015 model year, the Ford E-series cargo/passenger vans were replaced in North America by the Ford Transit; since then, only cutaway and stripped chassis configurations of the E-series are produced.

With a 59-year production run, the E-Series nameplate is outlasted only by the Ford F-Series (1948-present) in terms of longevity (for a Ford nameplate). From 1961 to 2005, Ford assembled the model line at Lorain Assembly (Lorain, Ohio); subsequent assembly has been located at Ohio Assembly (Avon Lake, Ohio). (thanks: wiki)

TPMS RESET

Note: Your need TPMS Scan tool for this car model.

Relearn Procedure for Models WITH STANDARD IGNITION.

  1. Inflate all tires to pressure listed on vehicleplacard.
  2. Turn ignition to OFF position and press and release brake pedal.
  3. Cycle ignition from the OFF to RUN position 3 times, ending in the RUN position.
  4. Press and release brake pedal.
  5. Turn ignition to OFF position.
  6. Cycle ignition from the OFF to RUN position 3 times, ending in the RUN position.
  7. Horn will sound once,and the TPMS telltale will blink once, indicating train mode is initiated. If equipped with a message center, it will display TRAIN LF TIRE.
  8. .Starting with the LF tire, use your TPMS scan tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped). The horn will sound once each sensor has been recognized.
  9. After training LR tire, the message center will display TRAINING MODE COMPLETE. If the vehicle is not equipped with the message center display, successful completion can be verified by turning the ignition to the OFF position and not hearing the horn sound. If the horn sounds, then the training procedure must be repeated.
  10. Turn ignition to the OFF position.

 

 

Relearn Procedure for Models WITH PUSH-BUTTON IGNITION.

  1. Inflate all tires to pressure listed on vehicle placard.2.With the
  2. vehicle off, press and release the brake pedal.
  3. Press,and hold,the START button until a chime sounds.
  4. Power OFF by pushing the button 1 time.
  5. Press,and hold, the S TART button until a chime sounds.
  6. Power OFF by pushing the button 1 time.
  7. Press,and hold, the START button until a chime sounds.
  8. Press and release the brake pedal.
  9. Power OFF by pushing the button 1 time.
  10. Press,and hold, theS TART button until a chime sounds.
  11. Power OFF by pushing the button 1 time.
  12. Press,and hold, the START button until a chime sounds.
  13. Power off by pushing the button 1 time.
  14. Press,and hold, the START button until a chime sounds.
  15. Horn will sound once,and the TPMS telltale will blink once, indicating train mode is initiated. If equipped with a message center, it will display TRAIN LF TIRE.
  16. Starting with the LF tire, use your TPMS scan tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped). The horn will sound once each sensor has been recognized.
  17. After training LR tire, the message center will display TRAINING MODE COMPLETE. If the vehicle is not equipped with the message center display, successful completion can be verified by turning the ignition to the OFF position and not hearing the horn sound. If the horn sounds, then the training procedure must be repeated.
  18. 18.Turn ignition to the OFF position.

 

Thank you very much!