CROWN VICTORIA TPMS RESET
How to Reset / Relearn the TPMS on Ford Crown Victoria from year 2007-2008-2009-2010-2011.
About Crown Victoria
The Ford Crown Victoria (“Crown Vic”) is a full-size sedan that was marketed and manufactured by Ford from the 1992 to the 2011 model years. The successor to the Ford LTD Crown Victoria, the Crown Victoria served as the flagship Ford sedan above the Ford Taurus, and was the Ford-branded version of the Mercury Grand Marquis. Ford marketed the Crown Victoria Police Interceptor police car to law-enforcement agencies, and a long-wheelbase version was introduced in 2002 for taxi cab fleet.
The Crown Victoria was produced on the rear wheel drive Ford Panther platform it shared with the Grand Marquis and Lincoln Town Car. From 1997 to 2011, the three sedans were the only full-frame rear wheel drive passenger cars produced in North America and the only non-luxury cars offered with a standard V8 engine.
The Crown Victoria, Police Interceptor, and Grand Marquis were produced at the St. Thomas Assembly in Southwold, Ontario, Canada, which closed in 2011. A 2012 Crown Victoria was the final vehicle produced at the facility as part of a small group of vehicles intended for export to the Middle East. Over 1.5 million Crown Victorias (including Police Interceptors) were manufactured by St. Thomas Assembly from 1991 to 2011. Ford did not replace the Crown Victoria, leaving the front wheel drive/all wheel drive Ford Taurus as the closest option.
TPMS RESET
Note: Your need TPMS Scan tool for this car model.
Relearn Procedure for Models WITH STANDARD IGNITION.
- Inflate all tires to pressure listed on vehicleplacard.
- Turn ignition to OFF position and press and release brake pedal.
- Cycle ignition from the OFF to RUN position 3 times, ending in the RUN position.
- Press and release brake pedal.
- Turn ignition to OFF position.
- Cycle ignition from the OFF to RUN position 3 times, ending in the RUN position.
- Horn will sound once,and the TPMS telltale will blink once, indicating train mode is initiated. If equipped with a message center, it will display TRAIN LF TIRE.
- .Starting with the LF tire, use your TPMS scan tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped). The horn will sound once each sensor has been recognized.
- After training LR tire, the message center will display TRAINING MODE COMPLETE. If the vehicle is not equipped with the message center display, successful completion can be verified by turning the ignition to the OFF position and not hearing the horn sound. If the horn sounds, then the training procedure must be repeated.
- Turn ignition to the OFF position.
Relearn Procedure for Models WITH PUSH-BUTTON IGNITION.
- Inflate all tires to pressure listed on vehicle placard.2.With the
- vehicle off, press and release the brake pedal.
- Press,and hold,the START button until a chime sounds.
- Power OFF by pushing the button 1 time.
- Press,and hold, the S TART button until a chime sounds.
- Power OFF by pushing the button 1 time.
- Press,and hold, the START button until a chime sounds.
- Press and release the brake pedal.
- Power OFF by pushing the button 1 time.
- Press,and hold, theS TART button until a chime sounds.
- Power OFF by pushing the button 1 time.
- Press,and hold, the START button until a chime sounds.
- Power off by pushing the button 1 time.
- Press,and hold, the START button until a chime sounds.
- Horn will sound once,and the TPMS telltale will blink once, indicating train mode is initiated. If equipped with a message center, it will display TRAIN LF TIRE.
- Starting with the LF tire, use your TPMS scan tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped). The horn will sound once each sensor has been recognized.
- After training LR tire, the message center will display TRAINING MODE COMPLETE. If the vehicle is not equipped with the message center display, successful completion can be verified by turning the ignition to the OFF position and not hearing the horn sound. If the horn sounds, then the training procedure must be repeated.
- 18.Turn ignition to the OFF position.
Thank you very much!