Ford Expedition TPMS Reset

FORD EXPEDITION TPMS RESET

How to reset the TPMS on Ford Expedition from year 2007-2008-2009-2010-2011-2012-2013-2014-2015-2016-2017-2018-2019.

About Ford Expedition:

The Ford Expedition is a Full-size SUV manufactured by Ford. Introduced for the 1997 model year as the successor of the Ford Bronco, the Expedition was the first full-size Ford SUV sold with a four-door body. For its entire production life, the Ford Expedition has been derived from the corresponding generation of the Ford F-150 in production, sharing some body and mechanical components. The fourth-generation Ford Expedition began production for the 2018 model year. Similar to the configuration of the Chevrolet Tahoe and Suburban, the Ford Expedition is sold in regular and extended lengths (the Ford Expedition EL/Max); sold since 2007, the latter functionally serves as the replacement for the Ford Excursion.

Since 1997, the Lincoln division has marketed the Ford Expedition as the Lincoln Navigator, the first full-size SUV sold by a luxury auto brand in North America (the Expedition was never sold as a Mercury). The third Ford vehicle to use the Expedition nameplate, the full-size SUV follows a 1992 F-150 Eddie Bauer concept vehicle and a 1995 trim level package on the two-door Ford Explorer Sport.

Prior to 2009, the Ford Expedition was assembled at the Michigan Assembly Plant in Wayne, Michigan (previously home to the Ford Bronco)., After 2009, the Ford Expedition was moved to the Kentucky Truck Plant in Louisville, Kentucky. (source:wiki)

TPMS RESET

Note: Your need TPMS Scan tool for this car model.

Relearn Procedure for Models WITH STANDARD IGNITION.

  1. Inflate all tires to pressure listed on vehicleplacard.
  2. Turn ignition to OFF position and press and release brake pedal.
  3. Cycle ignition from the OFF to RUN position 3 times, ending in the RUN position.
  4. Press and release brake pedal.
  5. Turn ignition to OFF position.
  6. Cycle ignition from the OFF to RUN position 3 times, ending in the RUN position.
  7. Horn will sound once,and the TPMS telltale will blink once, indicating train mode is initiated. If equipped with a message center, it will display TRAIN LF TIRE.
  8. .Starting with the LF tire, use your TPMS scan tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped). The horn will sound once each sensor has been recognized.
  9. After training LR tire, the message center will display TRAINING MODE COMPLETE. If the vehicle is not equipped with the message center display, successful completion can be verified by turning the ignition to the OFF position and not hearing the horn sound. If the horn sounds, then the training procedure must be repeated.
  10. Turn ignition to the OFF position.

 

 

Relearn Procedure for Models WITH PUSH-BUTTON IGNITION.

  1. Inflate all tires to pressure listed on vehicle placard.2.With the
  2. vehicle off, press and release the brake pedal.
  3. Press,and hold,the START button until a chime sounds.
  4. Power OFF by pushing the button 1 time.
  5. Press,and hold, the S TART button until a chime sounds.
  6. Power OFF by pushing the button 1 time.
  7. Press,and hold, the START button until a chime sounds.
  8. Press and release the brake pedal.
  9. Power OFF by pushing the button 1 time.
  10. Press,and hold, theS TART button until a chime sounds.
  11. Power OFF by pushing the button 1 time.
  12. Press,and hold, the START button until a chime sounds.
  13. Power off by pushing the button 1 time.
  14. Press,and hold, the START button until a chime sounds.
  15. Horn will sound once,and the TPMS telltale will blink once, indicating train mode is initiated. If equipped with a message center, it will display TRAIN LF TIRE.
  16. Starting with the LF tire, use your TPMS scan tool to scan each sensor in the following order: LF, RF, RR, LR (and full size spare if equipped). The horn will sound once each sensor has been recognized.
  17. After training LR tire, the message center will display TRAINING MODE COMPLETE. If the vehicle is not equipped with the message center display, successful completion can be verified by turning the ignition to the OFF position and not hearing the horn sound. If the horn sounds, then the training procedure must be repeated.
  18. 18.Turn ignition to the OFF position.

 

Thank you very much!

By erwincsalarda

Hello, my name is Erwin Salarda, and I'm from the Philippines. My main interests are computers and automobiles, and I am very enthusiastic about learning new things in life. Everything on my website was created with the intention of sharing it with you.