Ford Maverick RKE Keyfob Programming
The key fob programming tutorial guide for Ford Maverick from the years 2001, 2002, 2003, 2004, 2005, 2006, and 2007 to 2008. Please follow the tutorial below for your reference.
Ford Maverick 2001-2008 3 and 4 button Keyfob Programming
On this type of remote there are 2 possible instruction on how to program the keyfob on Ford Maverick.
PROGRAMMING INSTRUCTION 1
Note: Obtain all remote transmitters for this vehicle.
Note: Do not depress the brake pedal during procedure.
- Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (Off is the position where you can remove your key, RUN is the position just shy of starting your car.)
- Within 20 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 4.
- Within 20 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 3. For all other remotes.
- Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
PROGRAMMING INSTRUCTION 2
Note: Obtain all remote transmitters for this vehicle.
- Fasten seat belts and close all doors.
- Turn ignition from OFF to RUN 4 times within 6 seconds, with the 4th time ending in RUN. (Off is the position where you can remove your key, RUN is the position just shy of starting your car.)
- Turn ignition to OFF. Acoustic signal will sound and system warning lamp will illuminate to confirm programming mode.
- Within 10 seconds, press and hold any button on the first keyless remote. Wait for acoustic sound and warning lamp to flash (confirming programming) then release button on remote. Wait 2 seconds but within 10 seconds repeat step 4. For all other remotes. If you only have one remote then continue to step 5.
- Turn ignition to Crank or wait 10 seconds to end programming mode.
Ford Maverick 2001-2008 Keyless Remote Head Key Fob Programming
NOTE: You Must have Two Working Transponder Keys (keys that start your car) to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith. Your new key will need to be cut prior to programming.
- Insert an existing (working) key into the ignition cylinder.
- Turn the ignition cylinder ON (Position 3) and back to OFF (Position 1). Ignition should stay in ON position for at least three seconds but no more than ten seconds.
- Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition should stay in ON position for at least three seconds but no more than ten seconds.
- Remove the second key, insert the New (un-programmed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least six seconds and turn back to OFF.
- If the new key has been successfully programmed it will start the vehicle and operate the remote keyless entry system. The theft indicator light will light up for three seconds to indicate the key was successfully programmed.
If the new key was not successfully programmed, repeat steps 1-4. If the remote portion of the remote did not program but the key will start the vehicle, then please perform the procedure below to program the remote portion of your remote head key
Remote Portion of Key Fob (Only if the above procedure didn’t program the remote)
Obtain all remote transmitters for this vehicle. It’s not necessary to re-program your working remote head keys as those will continue to work. If you are programming additional non-remote head key remotes for your vehicle then they must all be programmed during this procedure. You are able to program up to four remotes in addition to your remote head keys.
Do not depress the brake pedal during procedure.
1.Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (Off is the position where you can remove your key, RUN is the position just shy of starting your car.)
2.Within 20 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 4.
3.Within 20 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 3. for all other remotes.
4.Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
I hope this instruction has been helpful in programming the car remote key. The Ford Maverick key fob programming instructional guide from 2001, 2002, 2003, 2004, 2005, 2006, and 2007 to 2008. Please see the instruction above for reference.