The Launch X431 has 356 Special Functions for BMW

The Launch X431 is equipped with 356  Special Functions for BMW

I had gathered all of the Launch X431’s special functions for BMW vehicles. I discovered that the Launch X431 has 356 extremely valuable special capabilities that will assist you in resolving all of your BMW car’s problems. The Launch X431 is the most powerful and dependable on-board diagnostics scanner available on the market. A number of additional functions are available, which may be useful while dealing with automotive problems. As of January 2022, the information contained herein is current; however, it is subject to change, and Launch X431 may have a range of new and unique functionalities in the future.

🇵🇭In the Philippines, we are the Launch X431 authorized dealer. We handle sales, training, and customer service. Please contact me at 0915 568 4578 if you have any questions. (We only offer after-sales support to customers who purchased the Launch X431 from our company)

Note:

The Launch X431 scanner is the best in the world. Every car upgrade of the Launch X431 scanner will be enjoyable for you. The Launch X431 scanner does not have a software lock, but all of these functions are available if your Launch X431 scanner is genuine. So, to avoid future issues, I recommend purchasing the Launch X431 from your local dealer. Even though your dealer’s pricing is significantly more than the price online, it is still far lower than the cost of dealing with the problem of buying counterfeit Launch X431 online. You can get your Launch X431 in the Philippines. Please contact me 0915 568 4578.

Watch this video to to explore the list of Special Function of Launch X431

The 356 Special Function for BMW Cars

• Function test of heater
• ACC sensor: Start-up
• Activate SDARS
• Activate recirculating pump unit
• Activating teach-in for angular offset between crankshaft and camshaft
• Activation of electric fuel pump control electronics
• Activation/deactivation, terminal 15
• Active Test
• Adaptation of the increment wheel
• Adapting the windscreen wiper
• Adjusting the electromotive throttle controller
• Adjusting the exhaust gas pressure sensor
• Adjusting the installation position of exhaust gas restriction flap
• Adjusting the wastegate linkage
• Adjustment of idle speed
• Adjustment of the driving dynamics sensors
• Adjustment, consumption calculation
• Aligning the characteristic map thermostat
• All-round vision camera: Check of the programming
• All-round vision camera: Transmit vehicle profile
• Anti-theft alarm system: Deactivate the monitoring of the diagnostic socket
• Autoaddressing ambient light BDC
• Autoaddressing of the light sources on the light effect manager
• Autoaddressing of the speaker illumination
• Automatic Hold brake: Activate/Deactivate workshop mode
• Automatic Hold brake: Start-up
• Automatic engine start-stop function: Starter exchange
• Auxiliary battery (24 V EPS): Register battery exchange
• Auxiliary battery for PCU: Register battery exchange
• Auxiliary battery: Register battery replacement
• Auxiliary heater: Initialisation of the Telestart transmitter
• Bedding-in workshop
• Bleed headlight cleaning system
• Bleeding DSC hydraulics
• Bleeding the fuel system
• Block and enable remote key
• Brake bleeding routine
• Brake fluid renewal
• Brake line mix-up test
• CBS Service Inclusive selection
• CBS functionality, engine oil impaired
• CBS reset
• CBS reset UDS
• CBS reset, engine oil
• CBS vehicle data correction
• CIC: Activate and deactivate test card
• CIM: Steering column calibration
• CO adjustment
• Calibration and teaching in for all-round vision camera
• Calibration run for flap motors
• Calibration run of the air distribution flap motors
• Change personalisation data of remote key
• Charging battery
• Charging the battery via diagnostic socket
• Charging the high-voltage battery: Read out history of last charging procedures
• Checking increment wheel adaptation
• Checking the locking status of the engine control unit
• Clean or replace exhaust-gas recirculation cooler
• Clear wear data
• Coasting: System check
• Coding
• Compare equipment specification
• Composition of the high-voltage battery unit: Read out serial numbers
• Compressor / first start-up
• Correction of undervoltage limits of the auxiliary heater
• DKG: Teach-in clutch slipping point
• DKG: flushing function
• DKG: oil adjustment
• DME – CAS adjustment
• DME – CAS interface
• DME – CAS interface 2
• DME: Delete adaptation variable camshaft timing control
• DME: Delete adaptations
• DSC control unit adjustment
• DSC: Adjustment of the driving dynamics sensors
• DSC: Auto. encoding
• DSC: Brake bleeding routine
• DSC: Brake line mix-up test:
• DSC: Start-up of DSC unit
• DWA: triggering
• Deactivation, engine oil
• Delete the personal profile
• Delete the secured mode
• Deleting engine adaptation values
• Determining the injectors
• Diesel particulate filter: Regeneration
• Diesel particulate filter: register replacement
• Disconnect high-voltage system from power: Read out reasons for prevention
• Driver’s side rear seat standardisation
• EDC: Function check, vertical acceleration sensors, damper satellites
• EDC: Initial operation
• EGS: Adapting clutch actuator hydraulic pumps
• EGS: Adapting the shift drums
• EGS: Learn parking
• EGS: Mechatronic calibration
• EGS: Renewal of the dual clutch
• EGS: Replace control unit
• EGS: Reset adaptation values
• EGS: Reset of the wear values of the transmission oil
• EGS: Teach in neutral position
• EGS: Transmission adaptation
• EGS: transmission fluid adjustment
• EGS: transmission flushing function
• EHC: Compressor cycle
• EHC: Delete data logger
• EHC: Pressure sensor
• EHC: Ride height sensors
• ELV: Partial standardisation
• ELV: Standardisation
• EME: Bleeding in low-temperature coolant circuit
• EME: Check 2-speed manual gearbox wear
• EME: Learning mechanical end stops of 2-gear manual gearbox
• EME: Motor position sensor adjustment
• EME: Read out the adjustment value of the rotor position sensor
• EME: Reset vacuum pump operating time
• EME: Rotor position sensor adjustment
• EME: Teach in drive position actuator
• EMF: Start-up, Automatic Hold brake
• EMF: Workshop mode, Automatic Hold brake
• EPS: Steering start-up
• ETH: Store configuration
• Electrical steering column adjustment standardisation
• Electronic ride height control (EHC): – Ride height sensor check
• Electronic ride height control (EHC): Air spring
• Electronic ride height control (EHC): Air supply system check
• Electronic ride height control (EHC): Bellows valve check
• Electronic ride height control (EHC): Check pressure accumulator sensor
• Electronic ride height control (EHC): Check, compressor relay
• Electronic ride height control (EHC): Compressor cycle
• Electronic ride height control (EHC): Pressure accumulator
• Electronic ride height control (EHC): Pressure sensor
• Electronic ride height control (EHC): Ride height adjustment
• Electronic ride height control (EHC): Status values
• Electronic ride height control (EHC): Transport mode
• Electronic ride height control (EHC): Valve, pressure accumulator
• Electronic ride height control (EHC): Vehicle level
• Electronic ride height control (EHC): Vent pressure accumulator
• Electronic tyre pressure specification data
• Enable airbag activation after programming operation
• Engine control unit: CCM history memory
• Engine measured variables
• Engine oil quantity
• Ethernet port configuration
• Evaluate closed-circuit current monitoring
• Evaluate the battery state of charge
• Expert mode
• Fault elimination CBS reset engine control unit
• Freeze Frame
• Front passenger seat occupancy detection, US version
• Front passenger seat, seat standardisation
• Fuel consumption display adjustment
• Fuel consumption display correction
• Fuel grade recognition
• Fuel quality recognition
• Fuel tank pressure sensor adjustment
• GHAS repair function
• Gearshift speed control
• HSR: Wheel alignment / functional check (articulation)
• HUD: – Setting picture geometry
• Head unit reset
• Heating and air conditioning functions: Address flap motors
• Heating and air conditioning functions: Calibrate selector wheels
• Heating and air conditioning functions: Calibration run for flap motors
• Heating and air conditioning functions: Drain / fill the refrigerant circuit
• Heating and air conditioning functions: Installation position of flap motors
• Heating and air conditioning functions: Run-in protection for A/C compressor
• Heating and air conditioning functions: Unlock electric auxiliary heater
• Heating and air conditioning functions: Unlocking auxiliary heater
• Heating and air conditioning system: Potentiometer
• High temperature cooling system bleeding
• High-voltage battery unit: Documenting the serial numbers of the cell modules
• High-voltage safety: Status
• ICM sensor system: Start-up
• Increase idle speed temporarily
• Initialisation of CBS after changing the engine control unit
• Initialisation of SCR tank system
• Initialisation of rain-light-solar-condensation sensor
• Initialisation of the component protection in the head unit
• Initialise audio operation at rear
• Initialise new headlight driver module and teach in turn indicator
• Initialise power window regulators
• Initialise rain sensor
• Initialise slide/tilt sunroof
• Initialise the top glove box
• Initialise trailer tow hitch
• Initialising Automatic Soft Closing
• Initialising the CID cover
• Initialising the curtain sunblind
• Initialising the curtains
• Initialising the radiator emblem
• Injection quantity compensation
• Installation mode
• Integration level
• Interior light autoaddressing
• Internal engine pressure
• JNAV: Change default software setting
• KAFAS: Calibration
• KAFAS: Reset calibration
• LDM: Pump motor calibration
• LDM: Ventilation
• Lane change warning: Start-up
• Learn Valvetronic limit positions
• Learning Valvetronic limit positions
• Learning glow elements
• Light adjustment for antiglare high-beam headlight and GZA
• Live Data
• Load starter battery and system battery.
• Long-distance range front radar sensor: Function test of heater
• Long-distance range front radar sensor: Start-up
• Lower front axle by 35 mm for camber adjustment
• MOST: Store configuration
• MOST: Storing the desired configuration
• MSA: Deactivate installation mode
• MSA: System check
• MSA: Teach in zero-gear sensor
• Microphone calibration audio amplifier
• Module Information
• NVE: Calibration
• Newly address the air distribution flap motors
• Normalise slide/tilt sunroof
• OBD Readiness Codes
• Oil-level adjustment
• On-board Diagnosis Readiness Codes
• Open and close radiator blind
• Open global VTC limit position adaptation
• Parking brake: Bedding-in procedure
• Parking brake: Initial operation
• Parking brake: Workshop mode
• Perform LIN autoaddressing
• Personalization
• Petrol particulate filter: – Request regeneration
• Petrol particulate filter: Initial operation
• Petrol particulate filter: register replacement
• Positioning-travel check
• Power Down command
• Power tailgate initialisation
• Power-down command
• Pressure coding service function, RDC integrated
• Program
• RDC: Initialisation
• RSE: Activate Kleer radio module
• RSE: Teach in radio remote control
• Radiator emblem installation position
• Rain sensor initialisation
• Read the Check Control history memory
• Reading out the readiness codes
• Rear driver’s side seat standardisation
• Rear passenger’s side seat standardisation
• Register battery exchange
• Register battery replacement
• Register teach acceleration sensor
• Registering lithium ion battery exchange
• Release electric auxiliary heater
• Remote door lock activations
• Remote key: Change personalisation data
• Remote key: Personalisation number
• Renew the control unit of the limited slip differential
• Replace combiner
• Reset SCR control unit installation mode
• Reset ZBM / SEC workshop mode
• Reset adaptation values
• Reset adaptations
• Reset correction values of injectors
• Reset running-in check
• Reset starter lock
• Reset the production mode for the fuel pump control module
• Reset: SCR switch-off scenario
• Resetting BMW Assist
• Retrofit
• Ride height sensors: Start-up
• SCR adjustments and adaptations
• SCR catalytic converter: register replacement
• SCR control unit: Reset assembly mode
• SCR system: resetting adaptations and adjustments
• SCR tank system: Start-up
• SCR tank system: System test
• SCR: Display of fuel tank level
• SZL: Steering angle sensor adjustment
• Safety system coding data
• Seat standardisation, driver’s seat
• Seat standardisation, front passenger seat
• Seat-occupancy detection, front passenger
• Service function display of measured data wheel electronics
• Service function display of the measured data of wheel electronics
• Service function measured data wheel electronics
• Service function pressure encoding for tyre pressure control integrated
• Service function, display and reset adaptation values
• Service function, pressure encoding
• Set installation position of the EGR valve
• Set transport mode
• Setting the transport mode
• Shock absorber adjustment
• Short range radar sensors: Reset correction angle
• Showroom Mode
• Sliding/tilt sunroof: move to service position
• Smooth running control
• Special Functions
• Start safety system (airbag):system time
• Start-up Valvetronic
• Start-up following walnut blasting
• Start-up for brake pedal travel sensor
• Start-up of fuel pump control electronics
• Start-up, Automatic Hold brake
• Starting up the high-voltage battery unit
• Steering angle sensor adjustment
• TCU subsequent evaluation
• TLC: Calibrate vibration motor
• Teach Touch Command snap-in adapter
• Teach in front light electronic turn signal
• Teach-in gear sensor
• Teach-in the exhaust flap or move it into the installation position
• Transfer box (VTG): Calibration
• Transfer box (VTG): Oil change
• Transfer box (VTG): Replace control unit
• Transmission control unit: Data adjustment, mechatronics
• Transmission control unit: Display and reset adaptation values
• Transmission control unit: Format fault memory
• Transmission control unit: Oil change
• Transmission control unit: Oil-level adjustment
• Transmission control unit: Reset learning function
• Transmission control unit: Reset torque characteristic curve
• Transmission control unit: Resetting adaption functions
• Transmission control unit: Standstill adaption
• Transmission control unit: Teach in valve characteristic curves PV1, PV2
• Transportability of a cell module: Electrical analysis
• Trouble Code
• Twin-clutch gearbox: , parking lock hook test
• Twin-clutch gearbox: Functional check, parking lock
• Twin-clutch gearbox: Gearbox adaptation
• ULF-SBX and ULF-SBX-H: – Log on mobile phone
• Update online services
• VDM: Self-diagnosis, troubleshooting
• VDM: Start self-diagnosis
• VDM: Start start-up
• VDM: Start-up, troubleshooting
• VDM: Study the adjustment value
• VDP: Air spring
• VDP: Compressor cycle
• VDP: Data memory
• VDP: Pressure accumulator
• VDP: Pressure sensor
• VDP: Ride height sensors
• VDP: Status values
• VDP: Transport mode
• VDP: Vehicle level
• VDP: Vertical-acceleration sensors
• Valvetronic lift adaptation
• Valvetronic mechanism/function
• Ventilation, cooling system
• Wastegate valve controller: Teach-in end stops/adjust wastegate linkage
• Wheel electronics: Warning and calibration data
• Workshop mode, Automatic Hold brake
• ZGM: FlexRay initialization
• cooling system: Ventilation
• initialize CID cover
• initialize radiator emblem

Compiled and Research by Erwin Salarda