How to Reset the TPMS on Geely Vehicles
Resetting the tire pressure monitoring system (TPMS) on Geely vehicles is a straightforward process, preventing underinflated tires and ensuring safe driving. This guide provides steps for resetting the TPMS on popular Geely models, including when a TPMS relearn procedure is necessary and how to perform it using an OBD scanner tool.
If the tire pressure monitoring system (TPMS) light is on in your Geely vehicle, it means the system has detected that one or more of your tires is significantly underinflated. Driving on underinflated tires is dangerous – it can cause uneven tire wear, reduced fuel efficiency, and even a tire blowout.
Luckily, resetting the TPMS on your Geely is a straightforward process in most cases. This comprehensive guide will walk you through the steps to reset the TPMS on popular Geely models and explain when a TPMS relearn procedure is necessary. We’ll also cover how to perform a TPMS relearn using an OBD scanner tool.
Geely Models Covered in this Guide
The TPMS reset and relearn procedures described here apply to the following Geely models:
- Geely Coolray
- Geely Azkarra
- Geely Okavango
- Geely Emgrand
- Geely Emgrand GL
- Geely Emgrand GS
- Geely Emgrand GT
- Geely Emgrand EV
- Geely Emgrand PHEV
- Geely Borui
- Geely Borui GE
- Geely Binyue
- Geely Binrui
- Geely Jiaji
- Geely Xingyue
- Geely Xingyue L
- Geely Preface
- Geely Icon
- Geely Haoyue
- Geely Geometry A
- Geely Geometry C
While the core steps are similar across models, always consult your owner’s manual for specific instructions for your exact year and model Geely vehicle. Safety is paramount when working on any vehicle.
How to Tell if You Need to Reset the TPMS
On most Geely models, a steady yellow TPMS warning light on the instrument panel indicates that one or more tires has low air pressure. The light looks like a cross-section of a tire with an exclamation mark inside.
If you see this light, check the pressure in all four tires with an accurate tire pressure gauge and add air as needed to reach the manufacturer-specified pressure. You can find the recommended cold tire pressures on a placard located inside the driver’s side door jamb.
Important: Do not rely on the tire pressure shown on the vehicle’s infotainment display or instrument panel as it may not update immediately. Always physically check tire pressure with a gauge after inflating.
After inflating the tires, the TPMS light should turn off within a few minutes of driving over 15 mph. If it remains on, you may need to perform a TPMS reset using the procedure below.
Performing a TPMS Reset on Geely Vehicles
Follow these steps to reset the TPMS on most Geely models:
- Park the vehicle and turn the ignition to the “ON” position without starting the engine.
- Locate the TPMS reset button. Its location varies by model:
- On the Coolray, Azkarra, and Okavango, it’s on the right side of the steering wheel.
- On the Emgrand, Borui, and Preface, it’s on the center console near the gear shifter.
- On the Binyue, Binrui, Jiaji, and Xingyue, it’s under the driver’s side dashboard to the left of the steering wheel.
- Press and hold the TPMS reset button until the tire pressure light blinks three times (typically 5-10 seconds).
- Release the button and start the engine.
- Drive the vehicle at 30 mph or more for at least 10 minutes to allow the TPMS to recalibrate.
The TPMS light should turn off once the system completes its recalibration. If the light remains on, there may be an issue with one of the tire pressure sensors or the TPMS module itself. Have the system diagnosed by a qualified Geely technician.
Note: If your Geely is not equipped with a dedicated TPMS reset button, you may need to use the vehicle settings menu in the infotainment system to access the reset function. Consult your owner’s manual for instructions specific to your model.
When is a TPMS Relearn Necessary?
While a basic TPMS reset is sufficient in most cases after adjusting tire pressures, there are certain situations that require a more in-depth TPMS relearn procedure:
- After rotating the tires
- After replacing one or more tires or wheels
- After replacing a tire pressure sensor
- When the TPMS light flashes for 60-90 seconds before staying solidly illuminated, indicating a system malfunction
During a relearn, the TPMS module re-memorizes the locations and sensor IDs of all four tire pressure sensors. This allows it to accurately determine the pressure of each individual tire and alert the driver if any tire becomes significantly underinflated.
On some older Geely models that use a passive, indirect TPMS, the relearn process involves driving at a steady speed to allow the system to recalibrate. However, most newer Geely vehicles use an active, direct TPMS with a sensor in each wheel. These require using an OBD scanner tool to initiate the relearn.
Performing a TPMS Relearn with an OBD Scanner
To perform a TPMS sensor relearn on your Geely, you’ll need an OBD-II scanner tool with TPMS relearn capabilities. A dedicated TPMS tool can also be used. Here’s a general overview of the process:
- Ensure all tires are inflated to the proper pressure based on the placard in the driver’s door jamb.
- Connect the OBD scanner to the vehicle’s diagnostic port, usually located under the dashboard to the left of the steering wheel.
- Turn the ignition on but do not start the engine.
- Using the scan tool, navigate to the TPMS relearn function. This is typically located under the “Body” or “Chassis” section.
- Select the option to relearn or program new TPMS sensor IDs.
- Starting with the left front tire, hold the scan tool against the sidewall near the valve stem to trigger the sensor.
- The scan tool will beep and display a message confirming it has read the sensor ID. Repeat this for the right front, right rear, and left rear tires in that order.
- Once all sensor IDs are registered, the scan tool will send the data to the TPMS module to complete the relearn. This may take up to 2 minutes.
- Verify the relearn was successful by checking that the TPMS light has turned off. If it remains on, retry the relearn procedure.
Important: The exact steps to perform a TPMS relearn with a scan tool may vary slightly depending on the make and model of the tool. Always refer to the tool’s user manual for specific operating instructions.
If you do not feel comfortable performing the TPMS relearn yourself, take your vehicle to a Geely dealer or qualified tire shop. Most will perform this service for a reasonable fee.
Frequently Asked TPMS Questions
Can I drive with the TPMS light on?
It is not advisable to drive with the TPMS light illuminated, as it indicates one or more of your tires may be significantly underinflated. This can cause uneven tread wear, reduced fuel economy, poor handling, and even a sudden tire failure.
If the TPMS light comes on while driving, find a safe place to pull over as soon as possible and check your tire pressures with a gauge. Add air as needed to reach the manufacturer’s recommended pressure, then perform a TPMS reset as described above. If the light remains on, have the system checked by a professional.
Why does the TPMS light come on in cold weather?
Tire pressure decreases by about 1 PSI for every 10°F drop in ambient temperature. So, if you last checked your tire pressure in warmer weather, the TPMS light may come on overnight during a cold snap as the air in the tires contracts. This is normal and does not necessarily indicate a problem with the TPMS.
Check your tire pressure frequently during the winter months and add air as needed to keep them properly inflated. As temperatures rise again in the spring, be sure to recheck the pressures and let air out if necessary to avoid over inflation.
Do I need to replace my TPMS sensors when I get new tires?
In most cases, you can reuse your existing TPMS sensors when you get new tires as long as they are still functioning properly. However, if a sensor is damaged, corroded, or has a dead battery, it will need to be replaced.
Most tire shops will automatically check the condition of your TPMS sensors when changing your tires and recommend replacement if necessary. If you do get new sensors, be sure to have them properly relearned to the vehicle as described above to ensure the TPMS functions correctly.
How long do TPMS sensors last?
TPMS sensors are designed to last at least 5-10 years depending on the make and model of your vehicle. However, exposure to harsh road conditions, extreme temperatures, and road salt can cause them to fail prematurely.
If you suspect a problem with one of your TPMS sensors, have it checked out by a qualified tire technician as soon as possible. Driving with a malfunctioning TPMS is a safety risk as it may not alert you to a dangerously low tire pressure.
Final words from Boss Erwin
Properly maintaining your Geely’s tire pressure monitoring system is essential for both safety and optimal vehicle performance. By regularly checking your tire pressures and promptly addressing any TPMS warning lights, you can extend the life of your tires, improve your fuel economy, and avoid dangerous blowouts on the road.