How to Reset and Relearn the TPMS of Volkswagen Lamando in All Generations

How to Reset and Relearn the TPMS of Volkswagen Lamando in All Generations

Learn how to reset and relearn the Tire Pressure Monitoring System (TPMS) for all generations of the Volkswagen Lamando. This guide explains what TPMS is, when to reset it, and provides step-by-step instructions for both first and second-generation models. It also covers troubleshooting tips and the importance of maintaining proper tire pressure for safety and efficiency. Keep your Lamando’s TPMS functioning well for a safer driving experience.

The Tire Pressure Monitoring System (TPMS) is a crucial safety feature in modern vehicles, including the Volkswagen Lamando. This system helps drivers maintain proper tire pressure, which is essential for optimal vehicle performance, fuel efficiency, and safety. In this comprehensive guide, we’ll explore how to reset and relearn the TPMS for all generations of the Volkswagen Lamando.

Understanding TPMS in Volkswagen Lamando

Before diving into the reset and relearn procedures, it’s important to understand what TPMS is and how it functions in the Volkswagen Lamando.

What is TPMS?

TPMS is an electronic system designed to monitor the air pressure inside pneumatic tires. It reports real-time tire pressure information to the driver, typically through a dashboard display or warning light.

Types of TPMS in Volkswagen Lamando

Volkswagen Lamando models may use one of two types of TPMS:

1. Direct TPMS: Uses physical pressure sensors in each tire to measure air pressure
2. Indirect TPMS: Uses wheel speed sensors from the anti-lock braking system (ABS) to detect underinflated tires

When to Reset or Relearn TPMS

You should reset or relearn your Volkswagen Lamando’s TPMS in the following situations:

• After rotating tires
• When replacing one or more tires
• After inflating tires to the correct pressure
• When the TPMS warning light remains on after properly inflating tires
• After replacing TPMS sensors

General TPMS Reset Procedure for Volkswagen Lamando

While specific procedures may vary slightly between generations, here’s a general method that works for many Volkswagen Lamando models:

1. Ensure all tires are inflated to the correct pressure as specified in the vehicle’s manual or driver’s side door jamb
2. Turn the ignition to the “ON” position without starting the engine
3. Locate the TPMS reset button (usually in the glove box or under the steering wheel)
4. Press and hold the TPMS reset button until the TPMS light blinks three times
5. Release the button and start the engine
6. Drive the vehicle for about 20 minutes at speeds above 16 mph (25 km/h) to complete the relearn process

TPMS Reset and Relearn Procedures by Lamando Generation

Let’s break down the specific procedures for each generation of the Volkswagen Lamando.

First Generation Lamando (2014-2018)

The first-generation Lamando typically uses an indirect TPMS system. To reset:

1. Inflate all tires to the correct pressure
2. Turn the ignition to “ON” (engine off)
3. Press the TPMS reset button located in the glove box
4. Hold the button until you hear a chime (about 3 seconds)
5. Start the engine and drive for at least 20 minutes to complete the relearn process

Second Generation Lamando (2019-Present)

The second-generation Lamando may use either direct or indirect TPMS, depending on the specific model and trim level.

For indirect TPMS:

1. Ensure all tires are properly inflated
2. Turn the ignition to “ON”
3. Navigate to the vehicle settings in the infotainment system
4. Select “Tire Pressure Monitoring”
5. Choose “Set New Tire Pressures”
6. Confirm the action
7. Drive the vehicle for about 20 minutes to complete the relearn process

For direct TPMS:

1. Inflate all tires to the correct pressure
2. Turn the ignition to “ON” (engine off)
3. Press the TPMS reset button (usually located near the steering wheel)
4. Hold until the TPMS light flashes
5. Start the engine and drive for at least 20 minutes at speeds above 16 mph (25 km/h)

Using a TPMS Tool for Relearn Procedures

For some Lamando models, especially those with direct TPMS, you may need a specialized TPMS tool to complete the relearn procedure. This is particularly true when replacing TPMS sensors.

Steps for using a TPMS tool:

1. Connect the TPMS tool to the vehicle’s OBD-II port
2. Follow the tool’s instructions to put the vehicle into relearn mode
3. Use the tool to activate each TPMS sensor in the following order: left front, right front, right rear, left rear
4. Wait for the tool to confirm that all sensors have been successfully programmed
5. Disconnect the tool and test drive the vehicle to ensure the TPMS is functioning correctly

Troubleshooting TPMS Issues in Volkswagen Lamando

If you’re experiencing persistent TPMS problems after attempting a reset or relearn, consider the following troubleshooting steps:

TPMS Light Stays On

• Double-check tire pressures, including the spare tire if applicable
• Ensure you’ve completed the entire relearn procedure, including the required drive time
• Check for damaged or corroded TPMS sensors
• Verify that all installed tires have compatible TPMS sensors

Intermittent TPMS Warnings

• Check for loose valve stem cores
• Inspect tires for slow leaks
• Verify that TPMS sensors are properly mounted
• Consider replacing sensor batteries if they’re more than 5-7 years old

Maintaining Your Lamando’s TPMS

To ensure your Volkswagen Lamando’s TPMS continues to function correctly:

• Regularly check tire pressures, at least once a month and before long trips
• Have TPMS sensors inspected during routine tire services
• Replace TPMS sensor batteries or entire sensors as recommended by Volkswagen (typically every 5-7 years)
• Be cautious when using tire sealants, as they can damage TPMS sensors
• When replacing tires, ensure new TPMS sensors are properly installed and programmed if necessary

The Importance of Proper Tire Pressure

Maintaining correct tire pressure in your Volkswagen Lamando is crucial for several reasons:

• Improved fuel efficiency
• Extended tire life
• Better handling and braking performance
• Reduced risk of tire failure
• Enhanced overall vehicle safety

The TPMS in your Lamando helps ensure these benefits by alerting you to potential pressure issues before they become serious problems.

Legal Requirements and TPMS

It’s worth noting that TPMS is not just a convenience feature; it’s a legal requirement in many countries. In the United States, for example, the TREAD Act mandates that all vehicles manufactured after September 1, 2007, must be equipped with a TPMS.

Conclusion

Resetting and relearning the TPMS in your Volkswagen Lamando is a straightforward process that can usually be completed in a few simple steps. By understanding how to perform this procedure, you can ensure your vehicle’s TPMS continues to function correctly, providing you with crucial information about your tire pressures.

Remember, while the TPMS is an excellent safety feature, it doesn’t replace the need for regular manual tire pressure checks. Make it a habit to check your tire pressures monthly and before long trips to ensure optimal performance and safety of your Volkswagen Lamando.

If you encounter persistent issues with your TPMS that you can’t resolve using these methods, it’s best to consult with a certified Volkswagen technician. They have the specialized tools and expertise to diagnose and resolve more complex TPMS problems.

By keeping your Lamando’s TPMS in good working order, you’re not just complying with legal requirements – you’re also ensuring a safer, more efficient, and more comfortable driving experience.