HOW TO GUIDE: Ford C-Max RKE Keyfob Programming

Ford C-Max RKE Keyfob Programming

The step by step tutorial on how to program the RKE Keyfob on Ford C-MAX from the year 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2013, 2014, 2015, 2016, 2017 to 2018. Please follow the instruction below for your guide.

Ford C-Max 2004-2010 RKE Keyfob Programming

cmax keyfob

  1. Preparatory Steps

    CLOSE and UNLOCK all doors using the power door locks.

    BUCKLE seat belts.

  2. Enter Vehicle Programming Mode

    INSERT key into Ignition and TURN from OFF to RUN 4 times within 10 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm Programming Mode.

  3. Program Remote

    Within 20 seconds press any button on first keyless remote fob. Door locks will cycle to confirm programming.

    (Repeat immediately for any additional remotes to be programmed.)

  4. Exit Programming Mode

    Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.

  5. Test Remotes

    Test all remotes. Programming is now complete.

Important:

  • Verify the following prior to following these instructions:
    • Your vehicle is equipped with keyless entry, and
    • You have a key fob remote that is compatible with your vehicle.
  • Obtain all remote transmitters for this vehicle. This procedure will erase all previously programmed remotes. You must program all existing and new remotes that you wish to use on the vehicle at this time.
  • You may clear your keyless entry system memory by entering programming mode as shown in the steps above.

Note: If your vehicle cannot enter programming mode, then you cannot program any remote.  This indicates either no keyless entry installed on the vehicle or a defective keyless entry receiver module.

Ford C-Max 2013-2018 RKE Keyfob Programming

Ford C-MAX instruction for HIGH SECURITY REMOTE HEAD KEYS

HIGH SECURITY REMOTE HEAD KEYS c-max

  1. Confirm First Programmed Key – Step 1

    INSERT the first previously programmed transponder key into the ignition.

  2. Confirm First Programmed Key – Step 2

    TURN the ignition from OFF to ON. KEEP the ignition ON for at least 3 seconds, but no more than 10 seconds.

  3. Confirm First Programmed Key – Step 3

    TURN the ignition OFF and REMOVE the first key from the ignition.

  4. Confirm Second Programmed Key – Step 1

    After 3 seconds, but within 10 seconds of turning the ignition OFF, INSERT the second previously programmed key into the ignition.

  5. Confirm Second Programmed Key – Step 2

    TURN the ignition from OFF to ON. KEEP the ignition ON for at least 3 seconds, but no more than 10 seconds.

  6. Confirm Second Programmed Key – Step 3

    TURN the ignition OFF and REMOVE the second key from the ignition.

  7. Program New Key – Step 1

    After 3 seconds but within 10 seconds of turning the ignition OFF and removing the second key, INSERT the NEW un-programmed key into the ignition.

  8. Program New Key – Step 2

    TURN the ignition from OFF to ON. KEEP the ignition ON for at least 6 seconds.

  9. Program New Key – Step 3

    REMOVE the NEW key from the ignition.

    If the key was successfully programmed, it will operate the remote entry system and start the vehicle’s engine.

    If the key was NOT successfully programmed, it will NOT work the remote entry system or start the vehicle’s engine and the message center will display “NO KEY DETECTED”. Wait 20 seconds and REPEAT the process from Step 1.

  10. Test Remotes

    TEST all remotes. Programming is complete.

  11. Share

    If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.

Important:

  • Verify the following prior to following these instructions:
    • Your vehicle is equipped with keyless entry, and
    • You have a key fob remote that is compatible with your vehicle.
  • You must have 2 working transponder chip keys in order to program a new transponder without the assistance of a professional.
  • The key to be programming must be cut prior to beginning this programming procedure.
  • To program any additional new keys, wait 20 seconds and REPEAT this procedure.

Note: If your vehicle cannot enter programming mode, then you cannot program any remote.  This indicates either no keyless entry installed on the vehicle or a defective keyless entry receiver module.

Ford C-MAX instruction for PEPS SMART KEY FOB REMOTE

ford c-max PEPS SMART KEY FOB REMOTE

  1. Enter Programming Mode – Step 1

    Have two programmed PEPS smart keys inside the vehicle prior to beginning this procedure.

    PLACE the NEW un-programmed smart key in the pocket inside the center console utility compartment.

  2. Enter Programming Mode – Step 2

    PRESS the driver or passenger power door UNLOCK button 3 times.

  3. Enter Programming Mode – Step 3

    PRESS and RELEASE the brake pedal 1 time.

  4. Enter Programming Mode – Step 4

    PRESS the driver or passenger power door LOCK button 3 times.

  5. Enter Programming Mode – Step 5

    PRESS and RELEASE the brake pedal 1 time. The INDICATOR on the START/STOP button should begin to rapidly flash, indicating Programming Mode has been entered.

  6. Program New PEPS Smart Key Remote

    Within 1 minute, PRESS the START/STOP button on the vehicle. A message will be displayed on the message center indicating that the NEW smart key was programmed successfully.

  7. Exit Programming Mode

    REMOVE the smart key from the utility compartment pocket and PRESS the UNLOCK or LOCK button on the NEW programmed smart key to EXIT programming mode.

  8. Test Remotes

    TEST all remotes. Programming is complete.

  9. Share

    If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.

Important:

  • Verify the following prior to following these instructions:
    • Your vehicle is equipped with keyless entry, and
    • You have a key fob remote that is compatible with your vehicle.
  • You must have 2 working PEPS smart keys in order to program a new key without the assistance of a professional.

Note: If your vehicle cannot enter programming mode, then you cannot program any remote.  This indicates either no keyless entry installed on the vehicle or a defective keyless entry receiver module.

Thank you very much! This tutorial was compiled and researched with ❤️ by Erwin Salarda.