Complete list of Error Codes of BRIGHT Wheel Balancers
Good day! Do you have problems with your Bright Wheel Balancer? Is there an error code displayed on the screen of your wheel balancer? In this blog post, I compiled the complete list of the error codes or trouble codes related to the BRIGHT wheel balancer machine. The error code number, the code description, the beep codes, and the cause of trouble are included in the article below.
LIST OF ERROR AND TROUBLE CODES
ERROR CODE: 000 to 009
PROBLEM: Machine parameters
SOLUTION: Contact technical support.
ERROR CODE: 010
PROBLEM: Reverse rotation of the wheel
SOLUTION: Contact technical support.
ERROR CODE: 011
PROBLEM: Wheel speed too low Check the main voltage.
SOLUTION: If the checks do not lead to any results, contact technical support.
ERROR CODE: 012
PROBLEM: The wheel cannot be stopped at the end of the launch
CAUSE: Loose or Faulty Magnetic Contact Switch
SOLUTION: Check the mains voltage. If the checks do not lead to any results, contact technical support.
ERROR CODE:
PROBLEM: 013 Wheel speed too high
SOLUTION: Contact technical support.
ERROR CODE: 014
PROBLEM: The wheel does not spin
SOLUTION: Contact technical support.
ERROR CODE: 015
PROBLEM: Keys pressed or jammed at start-up
SOLUTION: Release all buttons, then turn off or restart the machine. If the error persists, contact technical support.
ERROR CODE: 016
PROBLEM: Distance sensor not in rest position when the machine is switched on
SOLUTION: Set the sensor to its rest position: the error should disappear. If the error persists, contact technical support.
ERROR CODE: 017
PROBLEM: Width sensor not in rest position when the machine is switched on
SOLUTION: Set the sensor to its rest position: the error should disappear. If the error persists, contact technical support.
ERROR CODE: 018 Reserved
ERROR CODE: 019
PROBLEM: Communication processor failure
SOLUTION: Turn the machine off or on. If the error persists, contact technical support. The machine can still be used but all functions related to the USB port are disabled.
ERROR CODE: 020
PROBLEM: Lack of communication with the eeprom memory
SOLUTION: Turn the machine off and then on again. If the error persists, contact technical support.
ERROR CODE: 021
PROBLEM: Lack of machine calibration data or incorrect calibration data
SOLUTION: Carry out calibration for the CAR/SUV Wheel Type and/or for the MOTO Wheel Type. If the error persists, contact technical support. See also ERR030 and ERR031.
ERROR CODE: 022
PROBLEM: Pick-up channel A too high
SOLUTION: Excessive imbalance or anomaly. Turn the machine off and then on again. If the error persists, contact technical support.
ERROR CODE: 023
PROBLEM: Pick-up channel B too high
SOLUTION: Excessive imbalance or anomaly. Turn the machine off and then on again. If the error persists, contact technical support.
ERROR CODE: 024
PROBLEM: Internal timer channel too high
SOLUTION: Excessive imbalance or anomaly. Turn the machine off and then on again. If the error persists, contact technical support.
ERROR CODE: 025
PROBLEM: Presence of weight during the Cal0 calibration phase
SOLUTION: Remove the weight and repeat the launch of the Cal0 phase. If the error persists, contact technical support.
ERROR CODE: 026
PROBLEM: A launch without weight or failure of the pick-up A signal in the Cal2 calibration phase.
SOLUTION: Apply the intended weight and repeat the launch. If the error persists, contact technical support.
ERROR CODE: 27
PROBLEM: A launch without weight or failure of the pick-up B signal in the Cal2 calibration phase.
SOLUTION: Apply the intended weight and repeat the launch. If the error persists, contact technical support.
ERROR CODE: 028
PROBLEM: A launch with weight on the internal side during the Cal3 calibration phase. In this phase, the weight must be on the external side.
SOLUTION: Remove the weight from the internal side and repeat the launch. If the error persists, contact technical support.
ERROR CODE: 029 RESERVED
ERROR CODE: 030
PROBLEM: Lack of calibration data for the CAR/ SUV (auto-vehicle and off-road) Wheel Type
SOLUTION: Carry out calibration for the CAR/SUV wheel Type.
ERROR CODE: 031
PROBLEM: Lack of calibration data for the MOTO (motorbike) Wheel Type
SOLUTION: Carry out machine calibration for the MOTO Wheel Type.
ERROR CODE: 000 to 009″
DESCRIPTION: I NT ERR
TROUBLE: Machine parameters internal error.
SOLUTION: Contact technical support.
ERROR CODE: 010
DESCRIPTION: REV SRN
TROUBLE: Reverse rotation of the wheel.
SOLUTION: Contact technical support.
ERROR CODE: 012
DESCRIPTION: NO STP
TROUBLE: The wheel cannot be stopped at the end of the spin.
SOLUTION: Check the mains voltage. If the checks do not lead to any results, contact technical support.
ERROR CODE: 014
DESCRIPTION: NO SPN
TROUBLE: The wheel does not spin.
SOLUTION: Contact technical support.
ERROR CODE: 015
DESCRIPTION: (Blocked key code)
DISPLAY ERROR: “PERMANENT UNTIL TURNED OFF”
TROUBLE: Keypad blocked at start-up.
SOLUTION: “Release all keys, then turn off or restart the machine. If the error persists, contact technical support.”
ERROR CODE: 016
DESCRIPTION: DIS OUT
DISPLAY ERROR: OPERATOR ACTION
TROUBLE:WARNING: Distance sensor is not in rest position at start-up of the machine or when [P8] Start is pressed.
SOLUTION: Set the sensor to its rest position: the error should disappear. If the error persists, contact technical support.
ERROR CODE: 018
DESCRIPTION: NO BTI
TROUBLE: Impossible to communicate with expansion board.
SOLUTION: Contact technical support.
ERROR CODE: 019
DESCRIPTION: NO CP
TROUBLE:“WARNING: Communication process failure.”
SOLUTION: Turn the machine off and then on again. If the error persists contact technical support.
ERROR CODE: 020
DESCRIPTION: NO EEP
TROUBLE: Lack of communication with the eeprom memory.
SOLUTION: Contact technical support.
ERROR CODE: 021
DESCRIPTION: EEP ERR
DISPLAY ERROR: OPERATOR CONFIRMATION
TROUBLE: No machine calibration data or incorrect calibration data.
SOLUTION: Carry out calibration for the CAR/SUV Wheel Type and/or for the TRUCK Wheel Type. If the error persists, contact technical support.
ERROR CODE: 022
DESCRIPTION: -A- OUT
DISPLAY ERROR: OPERATOR CONFIRMATION
TROUBLE:“ERROR: Pick-up channel A too high.”
SOLUTION: Excessive imbalance or anomaly. Turn the machine off and then on again. If the error persists, check for pick-up failure Replace pick-up code.
ERROR CODE: 023
DESCRIPTION: -B- OUT
DISPLAY ERROR: OPERATOR CONFIRMATION
TROUBLE:“ERROR: Pick-up channel B too high.”
SOLUTION: Excessive imbalance or anomaly. Turn the machine off and then on again. If the error persists, check for pick-up failure Replace pick-up code.
ERROR CODE: 024
DISPLAY ERROR: OPERATOR CONFIRMATION “ERROR:
TROUBLE: Internal timer channel too high.”
SOLUTION: Excessive imbalance or anomaly. Turn the machine off and then on again. If the error persists, check for pick-up failure Replace pick-up code.
ERROR CODE: 025
DESCRIPTION: SHF IMB
DISPLAY ERROR: OPERATOR CONFIRMATION
TROUBLE: Presence of weight during the Cal0 calibration phase.
SOLUTION: Remove the weight and repeat the spin of the Cal0 phase. If the error persists, contact technical support.
ERROR CODE: 026
DESCRIPTION: NO –A-
DISPLAY ERROR: OPERATOR CONFIRMATION
TROUBLE: Spin without weight or no pick- up A signal in the Cal2 calibration phase.
SOLUTION: Apply the intended weight and repeat the spin. If the error persists, contact technical support.
ERROR CODE: 027
DESCRIPTION: NO –B-
DISPLAY ERROR: OPERATOR CONFIRMATION
TROUBLE: Spin without weight or no pick- up B signal in the Cal2 calibration phase.
SOLUTION: Apply the intended weight and repeat the spin. If the error persists, contact technical support.
ERROR CODE: 028
DESCRIPTION: INN IMB
DISPLAY ERROR: OPERATOR CONFIRMATION
TROUBLE:Spin with weight on the internal side during the Cal3 calibration phase.
SOLUTION: In this phase, the weight must be on the internal side. Remove the weight from the internal side and repeat the spin. If the error persists, contact technical support.
ERROR CODE: 030
DESCRIPTION: CAR CAL
DISPLAY ERROR: OPERATOR CONFIRMATION
TROUBLE:“No calibration data for the CAR/SUV (passenger car and off- road vehicle) Wheel Type.”
SOLUTION: Carry out the calibration of the machine for the CAR/SUV Wheel Type.
ERROR CODE: 031
DESCRIPTION: TRC CAL
DISPLAY ERROR: OPERATOR CONFIRMATION
TROUBLE:“No calibration data for the TRUCK Wheel Type.”
SOLUTION: Carry out machine calibration for the TRUCK Wheel Type.”
ERROR CODE: 032
DESCRIPTION: DIA CAL
DISPLAY ERROR: OPERATOR CONFIRMATION
TROUBLE:WARNING: Diameter sensor not calibrated. “ONLY TECHNICAL PERSONNEL.
SOLUTION: Calibrate the Diameter sensor.”
ERROR CODE: 036
DESCRIPTION: NO IMB
TROUBLE:“WARNING: Absence of wheel imbalance in DYNAMIC mode. It is not possible to run the low speed SWI procedure.”
ERROR CODE: 037
DESCRIPTION: O IMB
TROUBLE:“WARNING: Absence of wheel imbalance in STATIC mode. It is not possible to run the low speed SWI procedure.”
ERROR CODE: 039
DESCRIPTION: W.GUARD
TROUBLE:“WARNING/ERROR The wheel guard is open: the requested action cannot be performed.”
SOLUTION: Check guard MICRO switch.
ERROR CODE: 044
DESCRIPTION: DIA OFF
DISPLAY ERROR: OPERATOR CONFIRMATION
TROUBLE:“WARNING: Diameter sensor disabled or missing. It is not possible to perform the action required.”
SOLUTION: “ONLY TECHNICAL PERSONNEL. make sure that the sensor is connected and enabled.”
ERROR CODE: 046
DESCRIPTION: NO DIA
DISPLAY ERROR: OPERATOR CONFIRMATION
TROUBLE:WARNING: The Diameter sensor is enabled but disconnected.
SOLUTION: NOTE: if [F+P2] is pressed the machine acquisition system is temporarily disabled and operation can be continued.
ERROR CODE: 048
DESCRIPTION: CAL FAR
DISPLAY ERROR: OPERATOR CONFIRMATION
TROUBLE:WARNING: The Diameter sensor is too far from the calibration point.
SOLUTION: “ONLY TECHNICAL PERSONNEL. e-position the Diameter sensor into the correct calibration position.”
ERROR CODE: 050
DESCRIPTION: NO MY:
DISPLAY ERROR: OPERATOR CONFIRMATION
TROUBLE:WARNING Absence of wheel external imbalance. It is not Possible to use the Hidden weight program.
ERROR CODE: 051
DESCRIPTION: -: (>3 FAR
DISPLAY ERROR: OPERATOR CONFIRMATION
TROUBLE:WARNING: Hidden Weights programmed: the selected point is too far from the external imbalance position.”
SOLUTION: The point must be included up to 120′ from the external imbalance position.
ERROR CODE: 052
DESCRIPTION: : : 07 INC
DISPLAY ERROR: OPERATOR CONFIRMATION
TROUBLE:WARNING: Hidden Weights programmed: the external imbalance position is not between the selected WI and W2 points.”
SOLUTION: Choose WI and W2 points so that they include the external imbalance position.
ERROR CODE: 054
DESCRIPTION: : AB DSC
TROUBLE: Inverter cable with connection.
SOLUTION: Connect inverter cable.
ERROR CODE: 055
DESCRIPTION: NO OPT
DISPLAY ERROR: OPERATOR CONFIRMATION
TROUBLE:WARNING: The static imbalance of the wheel is too low: the Optimization’s programmed cannot be used.
ERROR CODE: 056
DESCRIPTION: HIS TM?
TROUBLE: High temperature on inverter.
SOLUTION: Contact technical support.
ERROR CODE: 057
DESCRIPTION: OVR VOL
TROUBLE: Over voltage on inverter.
SOLUTION: Contact technical support.
ERROR CODE: 058
DESCRIPTION: : IND VOL
TROUBLE: Under voltage on inverter.
SOLUTION: Contact technical support.
ERROR CODE: 059
DESCRIPTION: SOV RA
TROUBLE: Inverter overload.
SOLUTION: Contact technical support.
The error code can be exited in the following ways:
OPERATOR CONFIRMATION The machine exits the error code display when the operator presses any key (except for [P7] ).
OPERATOR ACTION The machine exits from the error code display when the operator performs an action linked to said error code (for example, ERR 016, brings the Distance sensor back to the rest position).
ONCE The machine displays the error code and its brief description just once, then it returns to the previous status.
PERMANENT The machine permanently displays this error code until being turned off, therefore the error code cannot be exited.
BRIGHT WHEEL BALANCER BEEP CODES
BEEP CODES: Short beep
MEANING: Selecting a program or a function
BEEP CODES: Long beep
MEANING: Acquisition Acquisition of a value (e.g. acquisition of wheel dimensions).
BEEP CODES: Double beep
MEANING: Warning A particular condition has occurred that requires the operator’s attention.
BEEP CODES: Triple beep
MEANING: Function not available or Error
DESCRIPTION: The requested function is not available or that an error condition has occurred.
BEEP CODES: Short beep + long beep
MEANING: Storing one or more values in the permanent memory (eeprom) of the circuit board
DESCRIPTION: One or more values have been stored in the permanent memory of the circuit board (for example, at completion of calibration phases).
BEEP CODES: Intermittent beep
MEANING: Adjustment
DESCRIPTION: Signal used in some service programs to simplify the adjustment of sensors.
THIS ERROR CODE MAY APPLY TO THESE BRIGHT WHEEL BALANCER MODELS.
- BP 900B FALCON
- BP 63 OSPREY
- BP 66 KITE
- BP 67 HARRIER
- BP 68 HAWK
- BP 76 EAGLE
- BP 78 BUZZARD
- BP 46 VULTURE
- CB66
- CB460B
- CB910GB
- CB63
- CB953LB
- CB46
- CB67
- CB68
- CB75
- CB76
- CB78P
I hope this tutorial is helpful to you! Thank you very much for visiting my website. -Erwin Salarda