AUDI OBD 1 AND OBD 2 CODE LIST
EOBD code | Failure type | |
00 | No failure type information | |
01 | General electrical failure | |
02 | General signal failure | |
03 | Frequency modulated (FM)/pulse width modulated (PWM) signal failure | |
04 | System internal failure | |
05 | System programming failure | |
06 | Algorithm based failure | |
07 | Mechanical failure | |
08 | Data bus signal/message failure | |
09 | Component failure | |
11 | Short circuit to earth | |
12 | Short circuit to positive | |
13 | Circuit open | |
14 | Open circuit/short to earth | |
15 | Open circuit/short to positive | |
16 | Circuit voltage below threshold | |
17 | Circuit voltage above threshold | |
18 | Circuit current below threshold | |
19 | Circuit current above threshold | |
1A | Circuit resistance below threshold | |
1B | Circuit resistance above threshold | |
1C | Circuit voltage out of range | |
1D | Circuit current out of range | |
1E | Circuit resistance out of range | |
1F | Circuit intermittent | |
21 | Signal amplitude below minimum | |
22 | Signal amplitude above maximum | |
23 | Signal stuck low | |
24 | Signal stuck high | |
25 | Signal shape/waveform failure | |
26 | Signal rate of change below threshold | |
27 | Signal rate of change above threshold | |
28 | Signal bias level out of range/zero adjustment failure | |
29 | Signal invalid | |
2A | Signal stuck in range | |
2B | Signal cross-coupled | |
2F | Signal erratic | |
31 | No signal | |
32 | Signal low time below minimum | |
33 | Signal low time above maximum | |
34 | Signal high time below minimum | |
35 | Signal high time above maximum | |
36 | Signal frequency too low | |
37 | Signal frequency too high | |
38 | Signal frequency incorrect | |
39 | Signal has too few pulses | |
3A | Signal has too many pulses | |
41 | General checksum failure | |
42 | General memory failure | |
43 | Special memory failure | |
44 | Data memory failure | |
45 | Program memory failure | |
46 | Calibration/parameter memory failure | |
47 | Watchdog/safety micro-controller failure | |
48 | Supervision software failure | |
49 | Internal electronic failure | |
4A | Incorrect component installed | |
4B | Over-temperature condition | |
51 | Component not programmed | |
52 | Component program not activated | |
53 | Component program disabled | |
54 | Missing calibration | |
55 | System not configured | |
56 | Invalid/incompatible configuration | |
57 | Invalid/incompatible software component | |
61 | Signal calculation failure | |
62 | Signal comparison failure | |
63 | Circuit/component protection time-out | |
64 | Signal plausibility failure | |
65 | Signal has too few transitions/events | |
66 | Signal has too many transitions/events | |
67 | Signal incorrect after event | |
68 | Event information | |
71 | Actuator stuck | |
72 | Actuator stuck open | |
73 | Actuator stuck closed | |
74 | Actuator slipping | |
75 | Emergency position not reachable | |
76 | Incorrect mounting position | |
77 | Commanded position not reachable | |
78 | Alignment or adjustment incorrect | |
79 | Mechanical linkage failure | |
7A | Fluid leak or seal failure | |
7B | Low fluid level | |
81 | Invalid serial data received | |
82 | Alive/sequence counter incorrect/not updated | |
83 | Value of signal protection calculation incorrect | |
84 | Signal below allowable range | |
85 | Signal above allowable range | |
86 | Signal invalid | |
87 | Missing message | |
88 | Data bus off | |
8F | Signal erratic | |
91 | Component parameter out of range | |
92 | Performance problem/malfunction | |
93 | No operation | |
94 | Unexpected component operation | |
95 | Incorrect assembly | |
96 | Component internal failure | |
97 | Component or system operation obstructed or blocked | |
98 | Component or system over-temperature condition | |
9A | Component or system operating conditions | |
EOBD code | Fault location | |
U3000 | Control module | |
U3001 | Control module – improper shut down | |
U3002 | Vehicle identification number (VIN) | |
U3003 | Battery voltage | |
U3004 | Accessory power relay | |
U3005 | Retained accessory power | |
U3006 | Control module – supply voltage input A | |
U3007 | Control module – supply voltage input B | |
U3008 | Control module – earth connection A | |
U3009 | Control module – earth connection B | |
U300A | Ignition switch | |
U300B | Ignition input signal, accessory/ON/start position – malfunction | |
U300C | Ignition input signal, OFF/ON/start position – malfunction | |
U300D | Ignition input signal, ON/start position – malfunction | |
U300E | Ignition input signal, ON position – malfunction | |
U300F | Ignition input signal, accessory position – malfunction | |
U3010 | Ignition input signal, start position – malfunction | |
U3011 | Ignition input signal, OFF position – malfunction | |
EOBD code | Fault location | |
U0001 | Controller area network (CAN) data bus, high speed bus | |
U0002 | Controller area network (CAN) data bus, high speed bus – performance problem | |
U0003 | Controller area network (CAN) data bus, high speed bus (+) – open circuit | |
U0004 | Controller area network (CAN) data bus, high speed bus (+) – voltage low | |
U0005 | Controller area network (CAN) data bus, high speed bus (+) – voltage high | |
U0006 | Controller area network (CAN) data bus, high speed bus (-) – open circuit | |
U0007 | Controller area network (CAN) data bus, high speed bus (-) – voltage low | |
U0008 | Controller area network (CAN) data bus, high speed bus (-) – voltage high | |
U0009 | Controller area network (CAN) data bus, high speed bus (-) – shorted to data bus (+) | |
U0010 | Controller area network (CAN) data bus, medium speed bus | |
U0011 | Controller area network (CAN) data bus, medium speed bus – performance problem | |
U0012 | Controller area network (CAN) data bus, medium speed bus (+) – open circuit | |
U0013 | Controller area network (CAN) data bus, medium speed bus (+) – voltage low | |
U0014 | Controller area network (CAN) data bus, medium speed bus (+) – voltage high | |
U0015 | Controller area network (CAN) data bus, medium speed bus (-) – open circuit | |
U0016 | Controller area network (CAN) data bus, medium speed bus (-) – voltage low | |
U0017 | Controller area network (CAN) data bus, medium speed bus (-) – voltage high | |
U0018 | Controller area network (CAN) data bus, medium speed bus (-) – shorted to data bus (+) | |
U0019 | Controller area network (CAN) data bus, low speed bus | |
U0020 | Controller area network (CAN) data bus, low speed bus – performance problem | |
U0021 | Controller area network (CAN) data bus, low speed bus (+) – open circuit | |
U0022 | Controller area network (CAN) data bus, low speed bus (+) – voltage low | |
U0023 | Controller area network (CAN) data bus, low speed bus (+) – voltage high | |
U0024 | Controller area network (CAN) data bus, low speed bus (-) – open circuit | |
U0025 | Controller area network (CAN) data bus, low speed bus (-) – voltage low | |
U0026 | Controller area network (CAN) data bus, low speed bus (-) – voltage high | |
U0027 | Controller area network (CAN) data bus, low speed bus (-) – shorted to data bus (+) | |
U0028 | Vehicle area network (VAN) data bus A | |
U0029 | Vehicle area network (VAN) data bus A – performance problem | |
U0030 | Vehicle area network (VAN) data bus A (+) – open circuit | |
U0031 | Vehicle area network (VAN) data bus A (+) – voltage low | |
U0032 | Vehicle area network (VAN) data bus A (+) – voltage high | |
U0033 | Vehicle area network (VAN) data bus A (-) – open circuit | |
U0034 | Vehicle area network (VAN) data bus A (-) – voltage low | |
U0035 | Vehicle area network (VAN) data bus A (-) – voltage high | |
U0036 | Vehicle area network (VAN) data bus A (-) – shorted to data bus A (+) | |
U0037 | Vehicle area network (VAN) data bus B | |
U0038 | Vehicle area network (VAN) data bus B – performance problem | |
U0039 | Vehicle area network (VAN) data bus B (+) – open circuit | |
U0040 | Vehicle area network (VAN) data bus B (+) – voltage low | |
U0041 | Vehicle area network (VAN) data bus B (+) – voltage high | |
U0042 | Vehicle area network (VAN) data bus B (-) – open circuit | |
U0043 | Vehicle area network (VAN) data bus B (-) – voltage low | |
U0044 | Vehicle area network (VAN) data bus B (-) – voltage high | |
U0045 | Vehicle area network (VAN) data bus B (-) – shorted to data bus B (+) | |
U0046 | Vehicle area network (VAN) data bus C | |
U0047 | Vehicle area network (VAN) data bus C – performance problem | |
U0048 | Vehicle area network (VAN) data bus C (+) – open circuit | |
U0049 | Vehicle area network (VAN) data bus C (+) – voltage low | |
U0050 | Vehicle area network (VAN) data bus C (+) – voltage high | |
U0051 | Vehicle area network (VAN) data bus C (-) – open circuit | |
U0052 | Vehicle area network (VAN) data bus C (-) – voltage low | |
U0053 | Vehicle area network (VAN) data bus C (-) – voltage high | |
U0054 | Vehicle area network (VAN) data bus C (-) – shorted to data bus C (+) | |
U0055 | Vehicle area network (VAN) data bus D | |
U0056 | Vehicle area network (VAN) data bus D – performance problem | |
U0057 | Vehicle area network (VAN) data bus D (+) – open circuit | |
U0058 | Vehicle area network (VAN) data bus D (+) – voltage low | |
U0059 | Vehicle area network (VAN) data bus D (+) – voltage high | |
U0060 | Vehicle area network (VAN) data bus D (-) – open circuit | |
U0061 | Vehicle area network (VAN) data bus D (-) – voltage low | |
U0062 | Vehicle area network (VAN) data bus D (-) – voltage high | |
U0063 | Vehicle area network (VAN) data bus D (-) – shorted to data bus D (+) | |
U0064 | Vehicle area network (VAN) data bus E | |
U0065 | Vehicle area network (VAN) data bus E – performance problem | |
U0066 | Vehicle area network (VAN) data bus E (+) – open circuit | |
U0067 | Vehicle area network (VAN) data bus E (+) – voltage low | |
U0068 | Vehicle area network (VAN) data bus E (+) – voltage high | |
U0069 | Vehicle area network (VAN) data bus E (-) – open circuit | |
U0070 | Vehicle area network (VAN) data bus E (-) – voltage low | |
U0071 | Vehicle area network (VAN) data bus E (-) – voltage high | |
U0072 | Vehicle area network (VAN) data bus E (-) – shorted to data bus E (+) | |
U0073 | Control module – data bus Off | |
U0074 | Control module communication bus B – data bus OFF | |
U0080 | Vehicle area network (VAN) data bus F | |
U0081 | Vehicle area network (VAN) data bus F – performance problem | |
U0082 | Vehicle area network (VAN) data bus F (+) – open circuit | |
U0083 | Vehicle area network (VAN) data bus F (+) – voltage low | |
U0084 | Vehicle area network (VAN) data bus F (+) – voltage high | |
U0085 | Vehicle area network (VAN) data bus F (-) – open circuit | |
U0086 | Vehicle area network (VAN) data bus F (-) – voltage low | |
U0087 | Vehicle area network (VAN) data bus F (-) – voltage high | |
U0088 | Vehicle area network (VAN) data bus F (-) – shorted to data bus F (+) | |
U0100 | Data bus, engine control module (ECM) A – no communication | |
U0101 | Data bus, transmission control module (TCM) – no communication | |
U0102 | Data bus, transfer box control module – no communication | |
U0103 | Data bus, gear shift module – no communication | |
U0104 | Data bus, cruise control module – no communication | |
U0105 | Data bus, injector control module – no communication | |
U0106 | Data bus, glow plug control module – no communication | |
U0107 | Data bus, throttle actuator control (TAC) module – no communication | |
U0108 | Data bus, alternative fuel control module – no communication | |
U0109 | Data bus, fuel pump (FP) control module – no communication | |
U010A | Exhaust gas recirculation (EGR) control module A – communication signal lost | |
U010B | Lost communication with exhaust gas recirculation (EGR) control module B | |
U010C | Turbocharger (TC)/supercharger (SC) control module A – communication signal lost | |
U010D | Turbocharger (TC)/supercharger (SC) control module B – communication signal lost | |
U010E | Reductant control module – communication signal lost | |
U010F | AC control module – communication signal lost | |
U0110 | Data bus, drive motor control module – no communication | |
U0111 | Data bus, battery energy control module A – no communication | |
U0112 | Data bus, battery energy control module B – no communication | |
U0113 | Data bus, emissions critical control information – no communication | |
U0114 | Data bus, four wheel drive clutch control module – no communication | |
U0115 | Data bus, engine control module (ECM) B – no communication | |
U0116 | Lost communication with coolant temperature control module | |
U0117 | Lost communication with power take-off (PTO) control module | |
U0118 | Lost communication with fuel additive control module | |
U0119 | Lost communication with fuel cell control module | |
U011A | Exhaust gas sensor control module – communication signal lost | |
U011B | Rocker arm control module A – communication signal lost | |
U011C | Rocker arm control module B – communication signal lost | |
U011D | Lost communication with four wheel drive control module | |
U011E | Lost communication with electronic throttle system (ETS) control module B | |
U0120 | Lost communication with starter/generator control module | |
U0121 | Data bus, anti-lock brake system (ABS) control module – no communication | |
U0122 | Data bus, vehicle dynamics control module – no communication | |
U0123 | Data bus, yaw rate sensor module – no communication | |
U0124 | Data bus, lateral acceleration sensor module – no communication | |
U0125 | Data bus, multi-axis acceleration sensor module – no communication | |
U0126 | Data bus, steering position sensor control module – no communication | |
U0127 | Data bus, tyre pressure monitor module – no communication | |
U0128 | Data bus, parking brake control module – no communication | |
U0129 | Data bus, brake system control module – no communication | |
U012A | Lost communication with chassis control module A | |
U012B | Lost communication with chassis control module B | |
U012C | Lost communication with active vibration control module | |
U0130 | Data bus, steering effort control module – no communication | |
U0131 | Data bus, power steering control module – no communication | |
U0132 | Data bus, suspension ride height control module – no communication | |
U0133 | Lost communication with active roll control module | |
U0134 | Lost communication with power steering control module, rear | |
U0135 | Lost communication with differential control module, front | |
U0136 | Lost communication with differential control module, rear | |
U0137 | Lost communication with trailer brake control module | |
U0138 | Lost communication with all-terrain control module | |
U0139 | Lost communication with suspension control module B | |
U0140 | Data bus, body control module (BCM) – no communication | |
U0141 | Data bus, body control module (BCM) A – no communication | |
U0142 | Data bus, body control module (BCM) B – no communication | |
U0143 | Data bus, body control module (BCM) C – no communication | |
U0144 | Data bus, body control module (BCM) D – no communication | |
U0145 | Data bus, body control module (BCM) E – no communication | |
U0146 | Data bus, gateway A – no communication | |
U0147 | Data bus, gateway B – no communication | |
U0148 | Data bus, gateway C – no communication | |
U0149 | Data bus, gateway D – no communication | |
U0150 | Data bus, gateway E – no communication | |
U0151 | Data bus, supplementary restraint system (SRS) control module – no communication | |
U0152 | Data bus, supplementary restraint system (SRS) control module, left – no communication | |
U0153 | Data bus, supplementary restraint system (SRS) control module, right – no communication | |
U0154 | Data bus, supplementary restraint system (SRS) occupant sensing control module – no communication | |
U0155 | Data bus, instrumentation control module – no communication | |
U0156 | Data bus, information centre A – no communication | |
U0157 | Data bus, information centre B – no communication | |
U0158 | Data bus, head up display – no communication | |
U0159 | Data bus, parking aid control module A – no communication | |
U0160 | Data bus, audible alert control module – no communication | |
U0161 | Data bus, compass module – no communication | |
U0162 | Data bus, navigation display module – no communication | |
U0163 | Data bus, navigation control module – no communication | |
U0164 | Data bus, AC control module – no communication | |
U0165 | Data bus, AC control module, rear | |
U0166 | Data bus, auxiliary heater control module – no communication | |
U0167 | Data bus, immobilizer control module – no communication | |
U0168 | Data bus, alarm system control module – no communication | |
U0169 | Data bus, sunroof control module – no communication | |
U016A | Lost communication with navigation control module | |
U016B | Lost communication with electric AC compressor control module | |
U016C | Lost communication with fuel pump control module B | |
U0170 | Data bus, supplementary restraint system (SRS) sensor A – no communication | |
U0171 | Data bus, supplementary restraint system (SRS) sensor B – no communication | |
U0172 | Data bus, supplementary restraint system (SRS) sensor C – no communication | |
U0173 | Data bus, supplementary restraint system (SRS) sensor D – no communication | |
U0174 | Data bus, supplementary restraint system (SRS) sensor E – no communication | |
U0175 | Data bus, supplementary restraint system (SRS) sensor F – no communication | |
U0176 | Data bus, supplementary restraint system (SRS) sensor G – no communication | |
U0177 | Data bus, supplementary restraint system (SRS) sensor H – no communication | |
U0178 | Data bus, supplementary restraint system (SRS) sensor I – no communication | |
U0179 | Data bus, supplementary restraint system (SRS) sensor J – no communication | |
U017A | Supplementary restraint system (SRS) system sensor K – communication signal lost | |
U017B | Supplementary restraint system (SRS) system sensor L – communication signal lost | |
U017C | Supplementary restraint system (SRS) system sensor M – communication signal lost | |
U017D | Supplementary restraint system (SRS) system sensor N – communication signal lost | |
U017E | Lost communication with seat belt pretensioner control module A | |
U017F | Lost communication with seat belt pretensioner control module B | |
U0180 | Data bus, automatic lighting control module – no communication | |
U0181 | Data bus, headlamp level control module – no communication | |
U0182 | Data bus, lamps control module, front – no communication | |
U0183 | Data bus, lamps control module, rear – no communication | |
U0184 | Data bus, radio – no communication | |
U0185 | Data bus, aerial module – no communication | |
U0186 | Data bus, audio unit output amplifier – no communication | |
U0187 | Data bus, digital disc player/changer module A – no communication | |
U0188 | Data bus, digital disc player/changer module B – no communication | |
U0189 | Data bus, digital disc player/changer module C – no communication | |
U0190 | Data bus, digital disc player/changer module D – no communication | |
U0191 | Data bus, television – no communication | |
U0192 | Data bus, personal computer – no communication | |
U0193 | Data bus, digital audio control module A – no communication | |
U0194 | Data bus, digital audio control module B – no communication | |
U0195 | Data bus, subscription entertainment receiver module – no communication | |
U0196 | Data bus, entertainment control module, rear – no communication | |
U0197 | Data bus, telephone control module – no communication | |
U0198 | Data bus, telematics control module – no communication | |
U0199 | Data bus, door function control module A – no communication | |
U0200 | Data bus, door function control module B – no communication | |
U0201 | Data bus, door function control module C – no communication | |
U0202 | Data bus, door function control module D – no communication | |
U0203 | Data bus, door function control module E – no communication | |
U0204 | Data bus, door function control module F – no communication | |
U0205 | Data bus, door function control module G – no communication | |
U0206 | Data bus, convertible top control module – no communication | |
U0207 | Data bus, moveable roof control module – no communication | |
U0208 | Data bus, seat adjustment control module A – no communication | |
U0209 | Data bus, seat adjustment control module B – no communication | |
U0210 | Data bus, seat adjustment control module C – no communication | |
U0211 | Data bus, seat adjustment control module D – no communication | |
U0212 | Data bus, steering column control module – no communication | |
U0213 | Data bus, mirror control module A – no communication | |
U0214 | Data bus, remote function actuation – no communication | |
U0215 | Data bus, door contact switch A – no communication | |
U0216 | Data bus, door contact switch B – no communication | |
U0217 | Data bus, door contact switch C – no communication | |
U0218 | Data bus, door contact switch D – no communication | |
U0219 | Data bus, door contact switch E – no communication | |
U0220 | Data bus, door contact switch F – no communication | |
U0221 | Data bus, door contact switch G – no communication | |
U0222 | Data bus, electric window motor A – no communication | |
U0223 | Data bus, electric window motor B – no communication | |
U0224 | Data bus, electric window motor C – no communication | |
U0225 | Data bus, electric window motor D – no communication | |
U0226 | Data bus, electric window motor E – no communication | |
U0227 | Data bus, electric window motor F – no communication | |
U0228 | Data bus, electric window motor G – no communication | |
U0229 | Data bus, heated steering wheel module – no communication | |
U0230 | Data bus, tailgate control module – no communication | |
U0231 | Data bus, rain sensor control module – no communication | |
U0232 | Data bus, side obstacle detection control module, left – no communication | |
U0233 | Data bus, side obstacle detection control module, right – no communication | |
U0234 | Data bus, convenience recall module – no communication | |
U0235 | Data bus, cruise control front distance range sensor – no communication | |
U0236 | Lost communication with steering column lock control module | |
U0237 | Lost communication with digital audio broadcast (DAB) control module C | |
U0238 | Lost communication with digital audio broadcast (DAB) control module D | |
U0239 | Lost communication with entrapment control module A | |
U023A | Image processing module A – communication signal lost | |
U023B | Image processing module B – communication signal lost | |
U023C | Image processing module C – communication signal lost | |
U023D | Lost communication with cruise control distance range sensor, front left | |
U023E | Lost communication with cruise control distance range sensor, front right | |
U0240 | Lost communication with entrapment control module B | |
U0241 | Lost communication with headlamp control module A | |
U0242 | Lost communication with headlamp control module B | |
U0243 | Lost communication with parking aid control module B | |
U0244 | Lost communication with running board control module A | |
U0245 | Lost communication with entertainment control module, front | |
U0246 | Lost communication with seat control module E | |
U0247 | Lost communication with seat control module F | |
U0248 | Lost communication with remote accessory module | |
U0249 | Lost communication with entertainment control module, rear B | |
U024A | Lost communication with interior lighting control module | |
U024B | Lost communication with seat control module G | |
U024C | Lost communication with seat control module H | |
U0250 | Lost communication with impact classification system module | |
U0251 | Lost communication with running board control module B | |
U0252 | Lost communication with rear lamps control module B | |
U0253 | Lost communication with accessory protocol interface module | |
U0254 | Lost communication with remote start module | |
U0255 | Lost communication with front display interface module | |
U0256 | Lost communication with front controls interface module A | |
U0257 | Lost communication with front controls/display interface module | |
U0258 | Lost communication with radio transceiver | |
U0259 | Lost communication with special purpose vehicle control module A | |
U025A | Special purpose vehicle control module B – communication signal lost | |
U025B | Special purpose vehicle control module C – communication signal lost | |
U025C | Special purpose vehicle control module D – communication signal lost | |
U025D | Lost communication with front controls interface module B | |
U0260 | Lost communication with seat adjustment control module A | |
U0261 | Lost communication with seat adjustment control module B | |
U0262 | Lost communication with audio unit output amplifier B | |
U0263 | Lost communication with voice activation control module | |
U0264 | Lost communication with camera module | |
U0286 | Lost communication with radiator anti-tamper device | |
U0287 | Lost communication with transmission fluid pump module | |
U0288 | Lost communication with DC to AC converter control module A | |
U0289 | Lost communication with DC to AC converter control module B | |
U0291 | Lost communication with gear shift module B | |
U0292 | Lost communication with drive motor control module B | |
U0293 | Lost communication with hybrid powertrain control module | |
U0294 | Lost communication with powertrain control monitor module | |
U0295 | Lost communication with AC to AC converter control module | |
U0296 | Lost communication with AC to DC converter control module A | |
U0297 | Lost communication with AC to DC converter control module B | |
U0298 | Lost communication with DC to DC converter control module A | |
U0299 | Lost communication with DC to DC converter control module B | |
U029A | Lost communication with hybrid battery pack sensor module | |
U029B | Lost communication with drive motor control module C | |
U029C | Lost communication with drive motor control module D | |
U029D | Lost communication with nitrogen oxides (NOx) sensor A | |
U029E | Lost communication with nitrogen oxides (NOx) sensor B | |
U029F | Lost communication with evaporative emission (EVAP) leak detection system control module | |
U0300 | Control module – internal software incompatibility | |
U0301 | Software incompatibility – engine control module (ECM) | |
U0302 | Software incompatibility – transmission control module (TCM) | |
U0303 | Software incompatibility – transfer box control module | |
U0304 | Software incompatibility – gear shift module | |
U0305 | Software incompatibility – cruise control module | |
U0306 | Software incompatibility – injector control module | |
U0307 | Software incompatibility – glow plug control module | |
U0308 | Software incompatibility – throttle actuator control (TAC) module | |
U0309 | Software incompatibility – alternative fuel control module | |
U030A | Software incompatibility with evaporative emission (EVAP) leak detection system control module | |
U0310 | Software incompatibility – fuel pump (FP) control module | |
U0311 | Software incompatibility – drive motor control module | |
U0312 | Software incompatibility – battery energy control module A | |
U0313 | Software incompatibility – battery energy control module B | |
U0314 | Software incompatibility – four wheel drive clutch control module | |
U0315 | Software incompatibility – anti-lock brake system (ABS) control module | |
U0316 | Software incompatibility – vehicle dynamics control module | |
U0317 | Software incompatibility – parking brake control module | |
U0318 | Software incompatibility – brake system control module | |
U0319 | Software incompatibility – steering effort control module | |
U0320 | Software incompatibility – power steering control module | |
U0321 | Software incompatibility – suspension ride height control module | |
U0322 | Software incompatibility – body control module | |
U0323 | Software incompatibility – instrumentation control module | |
U0324 | Software incompatibility – AC control module | |
U0325 | Software incompatibility – auxiliary heater control module | |
U0326 | Software incompatibility – immobilizer control module | |
U0327 | Software incompatibility – alarm system control module | |
U0328 | Software incompatibility – steering position sensor control module | |
U0329 | Software incompatibility – steering column control module | |
U0330 | Software incompatibility – tyre pressure monitor module | |
U0331 | Software incompatibility – body control module A | |
U0332 | Software incompatibility – multi-axis acceleration sensor module | |
U0333 | Software incompatibility with gear shift control module B | |
U0334 | Software incompatibility with audio system | |
U0335 | Software incompatibility with hybrid battery pack sensor module | |
U0336 | Software incompatibility with supplementary restraint system (SRS) control module | |
U0400 | Invalid data received | |
U0401 | Invalid data received – engine control module (ECM) | |
U0402 | Invalid data received – transmission control module (TCM) | |
U0403 | Invalid data received – transfer box control module | |
U0404 | Invalid data received – gear shift module | |
U0405 | Invalid data received – cruise control module | |
U0406 | Invalid data received – injector control module | |
U0407 | Invalid data received – glow plug control module | |
U0408 | Invalid data received – throttle actuator control (TAC) module | |
U0409 | Invalid data received – alternative fuel control module | |
U040A | Invalid data received from AC control module | |
U040B | Invalid data received from exhaust gas recirculation (EGR) control module A | |
U040C | Invalid data received from exhaust gas recirculation (EGR) control module B | |
U040D | Invalid data received from turbocharger (TC)/supercharger (SC) control module A | |
U040E | Invalid data received from turbocharger (TC)/supercharger (SC) control module B | |
U040F | Invalid data received from reductant control module | |
U0410 | Invalid data received – fuel pump (FP) control module | |
U0411 | Invalid data received – drive motor control module | |
U0412 | Invalid data received – battery energy control module A | |
U0413 | Invalid data received – battery energy control module B | |
U0414 | Invalid data received – four wheel drive clutch control module | |
U0415 | Invalid data received – anti-lock brake system (ABS) control module | |
U0416 | Invalid data received – vehicle dynamics control module | |
U0417 | Invalid data received – parking brake control module | |
U0418 | Invalid data received – brake system control module | |
U0419 | Invalid data received – steering effort control module | |
U041B | Invalid data received from exhaust gas sensor control module | |
U041C | Invalid data received from rocker arm control module A | |
U041D | Invalid data received from rocker arm control module B | |
U041E | Invalid data received from four wheel drive control module | |
U041F | Invalid data received from electronic throttle system (ETS) control module B | |
U0420 | Invalid data received – power steering control module | |
U0421 | Invalid data received – suspension ride height control module | |
U0422 | Invalid data received – body control module | |
U0423 | Invalid data received – instrumentation control module | |
U0424 | Invalid data received – AC control module | |
U0425 | Invalid data received – auxiliary heater control module | |
U0426 | Invalid data received – immobilizer control module | |
U0427 | Invalid data received – alarm system control module | |
U0428 | Invalid data received – steering position sensor control module | |
U0429 | Invalid data received – steering column control module | |
U042B | Invalid data received from chassis control module A | |
U042C | Invalid data received from chassis control module B | |
U042D | Invalid data received from active vibration control module | |
U0430 | Invalid data received – tyre pressure monitor module | |
U0431 | Invalid data received – body control module A | |
U0432 | Invalid data received from multi-axis acceleration sensor module | |
U0433 | Invalid data received from cruise control distance range sensor, front | |
U0434 | Invalid data received from active roll control module | |
U0435 | Invalid data received from power steering control module, rear | |
U0436 | Invalid data received from differential control module, front | |
U0437 | Invalid data received from differential control module, rear | |
U0438 | Invalid data received from trailer brake control module | |
U0439 | Invalid data received from all-terrain control module | |
U043A | Invalid data received from suspension control module B | |
U043B | Invalid data received from cruise control distance range sensor, front left | |
U043C | Invalid data received from cruise control distance range sensor, front right | |
U0441 | Invalid data received from emissions critical control information | |
U0442 | Invalid data received from ECM/PCM B | |
U0443 | Invalid data received from body control module (BCM) B | |
U0444 | Invalid data received from body control module (BCM) C | |
U0445 | Invalid data received from body control module (BCM) D | |
U0446 | Invalid data received from body control module (BCM) E | |
U0447 | Invalid data received from gateway A | |
U0448 | Invalid data received from gateway B | |
U0449 | Invalid data received from gateway C | |
U044A | Invalid data received from gateway D | |
U0450 | Invalid data received from gateway D | |
U0451 | Invalid data received from gateway E | |
U0452 | Invalid data received from supplementary restraint system (SRS) control module | |
U0453 | Invalid data received from side supplementary restraint system (SRS) control module, left | |
U0454 | Invalid data received from side supplementary restraint system (SRS) control module, right | |
U0455 | Invalid data received from restraints occupant classification system module | |
U0456 | Invalid data received from coolant temperature control module | |
U0457 | Invalid data received from information centre A | |
U0458 | Invalid data received from information centre B | |
U0459 | Invalid data received from head up display | |
U045A | Invalid data received from parking aid control module A | |
U0461 | Invalid data received from audible alert control module | |
U0462 | Invalid data received from compass module | |
U0463 | Invalid data received from navigation display module | |
U0464 | Invalid data received from navigation control module | |
U0465 | Invalid data received from power take-off (PTO) control module | |
U0466 | Invalid data received from AC control module, rear | |
U0467 | Invalid data received from fuel additive control module | |
U0468 | Invalid data received from fuel cell control module | |
U0469 | Invalid data received from starter/generator control module | |
U046A | Invalid data received from sunroof control module | |
U046B | Invalid data received from navigation control module | |
U046C | Invalid data received from electric AC compressor control module | |
U046D | Invalid data received from fuel pump control module B | |
U0471 | Invalid data received from supplementary restraint system (SRS) sensor A | |
U0472 | Invalid data received from supplementary restraint system (SRS) sensor B | |
U0473 | Invalid data received from supplementary restraint system (SRS) sensor C | |
U0474 | Invalid data received from supplementary restraint system (SRS) sensor D | |
U0475 | Invalid data received from supplementary restraint system (SRS) sensor E | |
U0476 | Invalid data received from supplementary restraint system (SRS) sensor F | |
U0477 | Invalid data received from supplementary restraint system (SRS) sensor G | |
U0478 | Invalid data received from supplementary restraint system (SRS) sensor H | |
U0479 | Invalid data received from supplementary restraint system (SRS) sensor I | |
U047A | Invalid data received from supplementary restraint system (SRS) system sensor J | |
U047B | Invalid data received from supplementary restraint system (SRS) system sensor K | |
U047C | Invalid data received from supplementary restraint system (SRS) system sensor L | |
U047D | Invalid data received from supplementary restraint system (SRS) system sensor M | |
U047E | Invalid data received from supplementary restraint system (SRS) system sensor N | |
U047F | Invalid data received from seat belt pretensioner control module A | |
U0480 | Invalid data received from seat belt pretensioner control module B | |
U0481 | Invalid data received from automatic lighting control module | |
U0482 | Invalid data received from headlamp level control module | |
U0483 | Invalid data received from lighting control module, front | |
U0484 | Invalid data received from lighting control module, rear A | |
U0485 | Invalid data received from audio system | |
U0486 | Invalid data received from aerial module | |
U0487 | Invalid data received from audio unit output amplifier A | |
U0488 | Invalid data received from digital disc player/changer module A | |
U0489 | Invalid data received from digital disc player/changer module B | |
U048A | Invalid data received from digital disc player/digital disc changer C | |
U0491 | Invalid data received from digital disc player/changer module D | |
U0492 | Invalid data received from television | |
U0493 | Invalid data received from personal computer | |
U0494 | Invalid data received from digital audio control module A | |
U0495 | Invalid data received from digital audio control module B | |
U0496 | Invalid data received from subscription entertainment receiver module | |
U0497 | Invalid data received from entertainment control module, rear A | |
U0498 | Invalid data received from telephone control module | |
U0499 | Invalid data received from telematics control module | |
U049A | Invalid data received from door function control module A | |
U0501 | Invalid data received from door function control module B | |
U0502 | Invalid data received from door function control module C | |
U0503 | Invalid data received from door function control module D | |
U0504 | Invalid data received from door function control module E | |
U0505 | Invalid data received from door function control module F | |
U0506 | Invalid data received from door function control module G | |
U0507 | Invalid data received from convertible top control module | |
U0508 | Invalid data received from moveable roof control module | |
U0509 | Invalid data received from seat control module A | |
U050A | Invalid data received from seat adjustment control module B | |
U0511 | Invalid data received from seat control module C | |
U0512 | Invalid data received from seat control module D | |
U0513 | Invalid data received from yaw rate sensor | |
U0514 | Invalid data received from mirror control module A | |
U0515 | Invalid data received from remote function actuation | |
U0516 | Invalid data received from door switch A | |
U0517 | Invalid data received from door switch B | |
U0518 | Invalid data received from door switch C | |
U0519 | Invalid data received from door switch D | |
U051A | Invalid data received from door switch E | |
U0521 | Invalid data received from door switch F | |
U0522 | Invalid data received from door switch G | |
U0523 | Invalid data received from door window motor A | |
U0524 | Invalid data received from door window motor B | |
U0525 | Invalid data received from door window motor C | |
U0526 | Invalid data received from door window motor D | |
U0527 | Invalid data received from door window motor E | |
U0528 | Invalid data received from door window motor F | |
U0529 | Invalid data received from door window motor G | |
U052A | Invalid data received from heated steering wheel function control module | |
U0531 | Invalid data received from rear gate module | |
U0532 | Invalid data received from rain sensing module | |
U0533 | Invalid data received from side obstacle detection control module, left | |
U0534 | Invalid data received from side obstacle detection control module, right | |
U0535 | Invalid data received from convenience recall module | |
U0536 | Invalid data received from lateral acceleration sensor module | |
U0537 | Invalid data received from steering column lock control module | |
U0538 | Invalid data received from digital audio control module C | |
U0539 | Invalid data received from digital audio control module D | |
U053A | Invalid data received from entrapment control module A | |
U053B | Invalid data received from image processing module A | |
U053C | Invalid data received from image processing module B | |
U053D | Invalid data received from image processing module C | |
U0541 | Invalid data received from entrapment control module B | |
U0542 | Invalid data received from headlamp control module A | |
U0543 | Invalid data received from headlamp control module B | |
U0544 | Invalid data received from parking aid control module B | |
U0545 | Invalid data received from running board control module | |
U0546 | Invalid data received from entertainment control module, front | |
U0547 | Invalid data received from seat control module E | |
U0548 | Invalid data received from seat control module F | |
U0549 | Invalid data received from remote accessory module | |
U054A | Invalid data received from rear entertainment control module B | |
U054B | Invalid data received from interior lighting control module | |
U054C | Invalid data received from seat control module G | |
U054D | Invalid data received from seat control module H | |
U0551 | Invalid data received from impact classification system module | |
U0552 | Invalid data received from running board control module B | |
U0553 | Invalid data received from lighting control module, rear B | |
U0554 | Invalid data received from accessory protocol interface module | |
U0555 | Invalid data received from remote start module | |
U0556 | Invalid data received from front display interface module | |
U0557 | Invalid data received from front controls interface module | |
U0558 | Invalid data received from front controls/display interface module | |
U0559 | Invalid data received from radio transceiver | |
U055A | Invalid data received from special purpose vehicle control module A | |
U055B | Invalid data received from special purpose vehicle control module B | |
U055C | Invalid data received from special purpose vehicle control module C | |
U055D | Invalid data received from special purpose vehicle control module D | |
U055E | Invalid data received from front controls interface module B | |
U0561 | Invalid data received from seat control switch module A | |
U0562 | Invalid data received from seat control switch module B | |
U0563 | Invalid data received from audio amplifier B | |
U0564 | Invalid data received from speech recognition module | |
U0565 | Invalid data received from camera module, rear | |
U0587 | Invalid data received from radiator anti-tamper device | |
U0588 | Invalid data received from transmission fluid pump module | |
U0589 | Invalid data received from DC to AC converter control module A | |
U058A | Invalid data received from DC/AC converter control module B | |
U0592 | Invalid data received from gear shift module B | |
U0593 | Invalid data received from drive motor control module B | |
U0594 | Invalid data received from hybrid powertrain control module | |
U0595 | Invalid data received from powertrain control monitor module | |
U0596 | Invalid data received from AC to AC converter control module | |
U0597 | Invalid data received from AC to DC converter control module A | |
U0598 | Invalid data received from AC to DC converter control module B | |
U0599 | Invalid data received from DC to DC converter control module A | |
U059A | Invalid data received from DC to DC converter control module B | |
U059B | Invalid data received from hybrid battery pack sensor control module | |
U059C | Invalid data received from drive motor control module C | |
U059D | Invalid data received from drive motor control module D | |
U059E | Invalid data received from nitrogen oxides (NOx) sensor A | |
U059F | Invalid data received from nitrogen oxides (NOx) sensor B | |
U05A0 | Invalid data received from evaporative emission (EVAP) leak detection system control module | |
EOBD code | Fault location | Probable cause |
P3400 | Cylinder deactivation system, bank 1 | – |
P3401 | Deactivation/intake valve control, cylinder 1 – open circuit | – |
P3402 | Deactivation/intake valve control, cylinder 1 – circuit performance | – |
P3403 | Deactivation/intake valve control, cylinder 1 – circuit low | – |
P3404 | Deactivation/intake valve control, cylinder 1 – circuit high | – |
P3405 | Exhaust valve control, cylinder 1 – open circuit | – |
P3406 | Exhaust valve control, cylinder 1 – circuit performance | – |
P3407 | Exhaust valve control, cylinder 1 – circuit low | – |
P3408 | Exhaust valve control, cylinder 1 – circuit high | – |
P3409 | Deactivation/intake valve control, cylinder 2 – open circuit | – |
P340A | Deactivation/intake valve control, bank 1 – circuit malfunction | – |
P340B | Deactivation/intake valve control, bank 2 – circuit malfunction | – |
P340C | Deactivation/exhaust valve control, bank 1 – circuit malfunction | – |
P340D | Deactivation/exhaust valve control, bank 2 – circuit malfunction | – |
P3410 | Deactivation/intake valve control, cylinder 2 – circuit performance | – |
P3411 | Deactivation/intake valve control, cylinder 2 – circuit low | – |
P3412 | Deactivation/intake valve control, cylinder 2 – circuit high | – |
P3413 | Exhaust valve control, cylinder 2 – open circuit | – |
P3414 | Exhaust valve control, cylinder 2 – circuit performance | – |
P3415 | Exhaust valve control, cylinder 2 – circuit low | – |
P3416 | Exhaust valve control, cylinder 2 – circuit high | – |
P3417 | Deactivation/intake valve control, cylinder 3 – open circuit | – |
P3418 | Deactivation/intake valve control, cylinder 3 – circuit performance | – |
P3419 | Deactivation/intake valve control, cylinder 3 – circuit low | – |
P341A | Deactivation/intake valve control, bank 1 – circuit performance problem | – |
P341B | Deactivation/intake valve control, bank 2 – circuit performance problem | – |
P341C | Deactivation/exhaust valve control, bank 1 – circuit performance problem | – |
P341D | Deactivation/exhaust valve control, bank 2 – circuit performance problem | – |
P3420 | Deactivation/intake valve control, cylinder 3 – circuit high | – |
P3421 | Exhaust valve control, cylinder 3 – open circuit | – |
P3422 | Exhaust valve control, cylinder 3 – circuit performance | – |
P3423 | Exhaust valve control, cylinder 3 – circuit low | – |
P3424 | Exhaust valve control, cylinder 3 – circuit high | – |
P3425 | Deactivation/intake valve control, cylinder 4 – open circuit | – |
P3426 | Deactivation/intake valve control, cylinder 4 – circuit performance | – |
P3427 | Deactivation/intake valve control, cylinder 4 – circuit low | – |
P3428 | Deactivation/intake valve control, cylinder 4 – circuit high | – |
P3429 | Exhaust valve control, cylinder 4 – open circuit | – |
P3430 | Exhaust valve control, cylinder 4 – circuit performance | – |
P3431 | Exhaust valve control, cylinder 4 – circuit low | – |
P3432 | Exhaust valve control, cylinder 4 – circuit high | – |
P3433 | Deactivation/intake valve control, cylinder 5 – open circuit | – |
P3434 | Deactivation/intake valve control, cylinder 5 – circuit performance | – |
P3435 | Deactivation/intake valve control, cylinder 5 – circuit low | – |
P3436 | Deactivation/intake valve control, cylinder 5 – circuit high | – |
P3437 | Exhaust valve control, cylinder 5 – open circuit | – |
P3438 | Exhaust valve control, cylinder 5 – circuit performance | – |
P3439 | Exhaust valve control, cylinder 5 – circuit low | – |
P3440 | Exhaust valve control, cylinder 5 – circuit high | – |
P3441 | Deactivation/intake valve control, – open circuit | – |
P3442 | Deactivation/intake valve control, cylinder 6 – circuit performance | – |
P3443 | Deactivation/intake valve control, cylinder 6 – circuit low | – |
P3444 | Deactivation/intake valve control, cylinder 6 – circuit high | – |
P3445 | Exhaust valve control, cylinder 6 – open circuit | – |
P3446 | Exhaust valve control, cylinder 6 – circuit performance | – |
P3447 | Exhaust valve control, cylinder 6 – circuit low | – |
P3448 | Exhaust valve control, cylinder 6 – circuit high | – |
P3449 | Deactivation/intake valve control, cylinder 7 – open circuit | – |
P3450 | Deactivation/intake valve control, cylinder 7 – circuit performance | – |
P3451 | Deactivation/intake valve control, cylinder 7 – circuit low | – |
P3452 | Deactivation/intake valve control, cylinder 7 – circuit high | – |
P3453 | Exhaust valve control, cylinder 7 – open circuit | – |
P3454 | Exhaust valve control, cylinder 7 – circuit performance | – |
P3455 | Exhaust valve control, cylinder 7 – circuit low | – |
P3456 | Exhaust valve control, cylinder 7 – circuit high | – |
P3457 | Deactivation/intake valve control, cylinder 8 – open circuit | – |
P3458 | Deactivation/intake valve control, cylinder 8 – circuit performance | – |
P3459 | Deactivation/intake valve control, cylinder 8 – circuit low | – |
P3460 | Deactivation/intake valve control, cylinder 8 – circuit high | – |
P3461 | Exhaust valve control, cylinder 8 – open circuit | – |
P3462 | Exhaust valve control, cylinder 8 – circuit performance | – |
P3463 | Exhaust valve control, cylinder 8 – circuit low | – |
P3464 | Exhaust valve control, cylinder 8 – circuit high | – |
P3465 | Deactivation/intake valve control, cylinder 9 – open circuit | – |
P3466 | Deactivation/intake valve control, cylinder 9 – circuit performance | – |
P3467 | Deactivation/intake valve control, cylinder 9 – circuit low | – |
P3468 | Deactivation/intake valve control, cylinder 9 – circuit high | – |
P3469 | Exhaust valve control, cylinder 9 – open circuit | – |
P3470 | Exhaust valve control, cylinder 9 – circuit performance | – |
P3471 | Exhaust valve control, cylinder 9 – circuit low | – |
P3472 | Exhaust valve control, cylinder 9 – circuit high | – |
P3473 | Deactivation/intake valve control, cylinder 10 – open circuit | – |
P3474 | Deactivation/intake valve control, cylinder 10 – circuit performance | – |
P3475 | Deactivation/intake valve control, cylinder 10 – circuit low | – |
P3476 | Deactivation/intake valve control, cylinder 10 – circuit high | – |
P3477 | Exhaust valve control, cylinder 10 – open circuit | – |
P3478 | Exhaust valve control, cylinder 10 – circuit performance | – |
P3479 | Exhaust valve control, cylinder 10 – circuit low | – |
P3480 | Exhaust valve control, cylinder 10 – circuit high | – |
P3481 | Deactivation/intake valve control, cylinder 11 – open circuit | – |
P3482 | Deactivation/intake valve control, cylinder 11 – circuit performance | – |
P3483 | Deactivation/intake valve control, cylinder 11 – circuit low | – |
P3484 | Deactivation/intake valve control, cylinder 11 – circuit high | – |
P3485 | Exhaust valve control, cylinder 11 – open circuit | – |
P3486 | Exhaust valve control, cylinder 11 – circuit performance | – |
P3487 | Exhaust valve control, cylinder 11 – circuit low | – |
P3488 | Exhaust valve control, cylinder 11 – circuit high | – |
P3489 | Deactivation/intake valve control, cylinder 12 – open circuit | – |
P3490 | Deactivation/intake valve control, cylinder 12 – circuit performance | – |
P3491 | Deactivation/intake valve control, cylinder 12 – circuit low | – |
P3492 | Deactivation/intake valve control, cylinder 12 – circuit high | – |
P3493 | Exhaust valve control, cylinder 12 – open circuit | – |
P3494 | Exhaust valve control, cylinder 12 – circuit performance | – |
P3495 | Exhaust valve control, cylinder 12 – circuit low | – |
P3496 | Exhaust valve control, cylinder 12 – circuit high | – |
P3497 | Cylinder deactivation system, bank 2 | – |
EOBD | ||
Fault location | ||
code | ||
P2000 | Nitrogen oxides (NOx) trap, bank 1 – efficiency below threshold | NOx trap |
P2001 | Nitrogen oxides (NOx) trap, bank 2 – efficiency below threshold | NOx trap |
P2002 | Particulate trap, bank 1 – efficiency below threshold | Particulate trap |
P2003 | Particulate trap, bank 2 – efficiency below threshold | Particulate trap |
Intake manifold air control actuator, bank 1 – actuator stuck | Wiring, intake manifold air control actuator, mechanical | |
P2004 | ||
open | fault | |
Intake manifold air control solenoid, bank 1 – solenoid stuck | Wiring, intake manifold air control solenoid, mechanical | |
P2004 | ||
open | fault | |
Intake manifold air control actuator, bank 2 – actuator stuck | Wiring, intake manifold air control actuator, mechanical | |
P2005 | ||
open | fault | |
Intake manifold air control solenoid, bank 2 – solenoid stuck | Wiring, intake manifold air control solenoid, mechanical | |
P2005 | ||
open | fault | |
Intake manifold air control actuator, bank 1 – actuator stuck | Wiring, intake manifold air control actuator, mechanical | |
P2006 | ||
closed | fault | |
Intake manifold air control solenoid, bank 1 – solenoid stuck | Wiring, intake manifold air control solenoid, mechanical | |
P2006 | ||
closed | fault | |
Intake manifold air control actuator, bank 2 – actuator stuck | Wiring, intake manifold air control actuator, mechanical | |
P2007 | ||
closed | fault | |
Intake manifold air control solenoid, bank 2 – solenoid stuck | Wiring, intake manifold air control solenoid, mechanical | |
P2007 | ||
closed | fault | |
P2008 | Intake manifold air control actuator, bank 1 – open circuit | Wiring open circuit, intake manifold air control actuator |
P2008 | Intake manifold air control solenoid, bank 1 – open circuit | Wiring open circuit, intake manifold air control solenoid |
Wiring short to earth, intake manifold air control | ||
P2009 | Intake manifold air control actuator, bank 1 – circuit low | |
actuator | ||
Wiring short to earth, intake manifold air control | ||
P2009 | Intake manifold air control solenoid, bank 1 – circuit low | |
solenoid | ||
Intake manifold air control actuator, bank 1 – performance | ||
P200A | Wiring, intake manifold air control actuator, ECM | |
problem | ||
Intake manifold air control actuator, bank 2 – performance | ||
P200B | Wiring, intake manifold air control actuator, ECM | |
problem | ||
Diesel particulate filter (DPF), bank 1 – over-temperature | ||
P200C | – | |
condition | ||
Diesel particulate filter (DPF), bank 2 – over-temperature | ||
P200D | – | |
condition | ||
P200E | Catalytic converter, bank 1 – over-temperature condition | – |
P200F | Catalytic converter, bank 2 – over-temperature condition | – |
Wiring short to positive, intake manifold air control | ||
P2010 | Intake manifold air control actuator, bank 1 – circuit high | |
actuator | ||
Wiring short to positive, intake manifold air control | ||
P2010 | Intake manifold air control solenoid, bank 1 – circuit high | |
solenoid | ||
P2011 | Intake manifold air control actuator, bank 2 – open circuit | Wiring open circuit, intake manifold air control actuator |
P2011 | Intake manifold air control solenoid, bank 2 – open circuit | Wiring open circuit, intake manifold air control solenoid |
Wiring short to earth, intake manifold air control | ||
P2012 | Intake manifold air control actuator, bank 2 – circuit low | |
actuator | ||
Wiring short to earth, intake manifold air control | ||
P2012 | Intake manifold air control solenoid, bank 2 – circuit low | |
solenoid | ||
Wiring short to positive, intake manifold air control | ||
P2013 | Intake manifold air control actuator, bank 2 – circuit high | |
actuator | ||
Wiring short to positive, intake manifold air control | ||
P2013 | Intake manifold air control solenoid, bank 2 – circuit high | |
solenoid | ||
Intake manifold air control actuator position sensor/switch, | Wiring, intake manifold air control actuator position | |
P2014 | ||
bank 1 – circuit malfunction | sensor/switch | |
Intake manifold air control actuator position sensor/switch, | Wiring, mechanical fault, intake manifold air control | |
P2015 | ||
bank 1 – range/performance problem | actuator position sensor/switch | |
Intake manifold air control actuator position sensor/switch, | Wiring short to earth, intake manifold air control | |
P2016 | ||
bank 1 – circuit low | actuator position sensor/switch | |
Intake manifold air control actuator position sensor/switch, | Wiring short to positive, intake manifold air control | |
P2017 | ||
bank 1 – circuit high | actuator position sensor/switch | |
Intake manifold air control actuator position sensor/switch, | Wiring, poor connection, intake manifold air control | |
P2018 | ||
bank 1 – circuit intermittent | actuator position sensor/switch | |
Intake manifold air control actuator position sensor/switch, | Wiring, intake manifold air control actuator position | |
P2019 | ||
bank 2 – circuit malfunction | sensor/switch | |
P201A | Reductant injector, unit 1, bank 2 – circuit range/performance | – |
Intake manifold air control actuator, bank 1 – supply voltage | ||
P201B | Wiring, intake manifold air control actuator, ECM | |
low | ||
Intake manifold air control actuator, bank 2 – supply voltage | ||
P201C | Wiring, intake manifold air control actuator, ECM | |
low | ||
Intake manifold air control actuator, bank 1 – internal | ||
P201D | Wiring, intake manifold air control actuator | |
malfunction | ||
Intake manifold air control actuator, bank 2 – internal | ||
P201E | Wiring, intake manifold air control actuator | |
malfunction | ||
Intake manifold air control actuator position sensor/switch, | Wiring, mechanical fault, intake manifold air control | |
P2020 | ||
bank 2 – range/performance problem | actuator position sensor/switch | |
Intake manifold air control actuator position sensor/switch, | Wiring short to earth, intake manifold air control | |
P2021 | ||
bank 2 – circuit low | actuator position sensor/switch | |
Intake manifold air control actuator position sensor/switch, | Wiring short to positive, intake manifold air control | |
P2022 | ||
bank 2 – circuit high | actuator position sensor/switch | |
Intake manifold air control actuator position sensor/switch, | Wiring, poor connection, intake manifold air control | |
P2023 | ||
bank 2 – circuit intermittent | actuator position sensor/switch | |
Evaporative emission (EVAP) fuel vapour temperature sensor – | ||
P2024 | Wiring, EVAP fuel vapour temperature sensor | |
circuit malfunction | ||
Evaporative emission (EVAP) fuel vapour temperature sensor – | ||
P2025 | Wiring, EVAP fuel vapour temperature sensor | |
range/performance problem | ||
Evaporative emission (EVAP) fuel vapour temperature sensor – | Wiring short to earth, EVAP fuel vapour temperature | |
P2026 | ||
low voltage | sensor | |
Evaporative emission (EVAP) fuel vapour temperature sensor – | Wiring short to positive, EVAP fuel vapour temperature | |
P2027 | ||
high voltage | sensor | |
Evaporative emission (EVAP) fuel vapour temperature sensor – | Wiring, poor connection, EVAP fuel vapour temperature | |
P2028 | ||
circuit intermittent | sensor | |
P2029 | Auxiliary heater (fuel fired) – system disabled | Auxiliary heater system |
P202A | Reductant tank heater control – open circuit | Wiring, reductant tank heater, ECM |
P202B | Reductant tank heater control – circuit low | Wiring, reductant tank heater, ECM |
P202C | Reductant tank heater control – circuit high | Wiring, reductant tank heater, ECM |
P202D | Reductant leakage | – |
P202E | Reductant injector – circuit range/performance | Wiring, reductant injector, ECM |
P202F | Reductant supply control – circuit range/performance | – |
P2030 | Auxiliary heater (fuel fired) – performance problem | Auxiliary heater system |
Exhaust gas temperature (EGT) sensor 2, bank 1 – circuit | ||
P2031 | Wiring, EGT sensor | |
malfunction | ||
P2032 | Exhaust gas temperature (EGT) sensor 2, bank 1 – circuit low | Wiring short to earth, EGT sensor |
P2033 | Exhaust gas temperature (EGT) sensor 2, bank 1 – circuit high | Wiring short to positive, EGT sensor |
Exhaust gas temperature (EGT) sensor 2, bank 2 – circuit | ||
P2034 | Wiring, EGT sensor | |
malfunction | ||
P2035 | Exhaust gas temperature (EGT) sensor 2, bank 2 – circuit low | Wiring short to earth, EGT sensor |
P2036 | Exhaust gas temperature (EGT) sensor 2, bank 2 – circuit high | Wiring short to positive, EGT sensor |
P2037 | Reductant injection air pressure sensor – circuit malfunction | Wiring, reductant injection air pressure sensor |
Reductant injection air pressure sensor – range/performance | ||
P2038 | Wiring, reductant injection air pressure sensor | |
problem | ||
Wiring short to earth, reductant injection air pressure | ||
P2039 | Reductant injection air pressure sensor – low input | |
sensor | ||
P203A | Reductant level sensor – circuit malfunction | Wiring, reductant level sensor, ECM |
P203B | Reductant level sensor – circuit range/performance | Wiring, reductant level sensor, ECM |
P203C | Reductant level sensor – circuit low | Wiring, reductant level sensor, ECM |
P203D | Reductant level sensor – circuit high | Wiring, reductant level sensor, ECM |
P203E | Reductant level sensor – circuit intermittent/erratic | Wiring, reductant level sensor, ECM |
P203F | Reductant level – low | – |
Wiring short to positive, reductant injection air pressure | ||
P2040 | Reductant injection air pressure sensor – high input | |
sensor | ||
P2041 | Reductant injection air pressure sensor – circuit intermittent | Wiring, reductant injection air pressure sensor |
P2042 | Reductant temperature sensor – circuit malfunction | Wiring, reductant temperature sensor |
P2043 | Reductant temperature sensor – range/performance problem | Wiring, reductant temperature sensor |
P2044 | Reductant temperature sensor – low input | Wiring, reductant temperature sensor |
P2045 | Reductant temperature sensor – high input | Wiring, reductant temperature sensor |
P2046 | Reductant temperature sensor – circuit intermittent | Wiring, reductant temperature sensor |
P2047 | Reductant injector 1, bank 1 – open circuit | Wiring, reductant injector |
P2048 | Reductant injector 1, bank 1 – circuit low | Wiring short to earth, reductant injector |
P2049 | Reductant injector 1, bank 1 – circuit high | Wiring short to positive, reductant injector |
P204A | Reductant pressure sensor – circuit malfunction | Wiring, reductant pressure sensor, ECM |
P204B | Reductant pressure sensor – circuit range/performance | Wiring, reductant pressure sensor, ECM |
P204C | Reductant pressure sensor – circuit low | Wiring, reductant pressure sensor, ECM |
P204D | Reductant pressure sensor – circuit high | Wiring, reductant pressure sensor, ECM |
P204E | Reductant pressure sensor – circuit intermittent/erratic | Wiring, reductant pressure sensor, ECM |
P204F | Reductant system, bank 1 – performance problem | – |
P2050 | Reductant injector 1, bank 2 – open circuit | Wiring, reductant injector |
P2051 | Reductant injector 1, bank 2 – circuit low | Wiring short to earth, reductant injector |
P2052 | Reductant injector 1, bank 2 – circuit high | Wiring short to positive, reductant injector |
P2053 | Reductant injector 2, bank 1 – open circuit | Wiring, reductant injector |
P2054 | Reductant injector 2, bank 1 – circuit low | Wiring short to earth, reductant injector |
P2055 | Reductant injector 2, bank 1 – circuit high | Wiring short to positive, reductant injector |
P2056 | Reductant injector 2, bank 2 – open circuit | Wiring, reductant injector |
P2057 | Reductant injector 2, bank 2 – circuit low | Wiring short to earth, reductant injector |
P2058 | Reductant injector 2, bank 2 – circuit high | Wiring short to positive, reductant injector |
P2059 | Reductant injection air pump – open circuit | Wiring, reductant injection air pump |
P205A | Reductant temperature sensor – circuit malfunction | Wiring, reductant tank temperature sensor, ECM |
P205B | Reductant temperature sensor – circuit range/performance | Wiring, reductant tank temperature sensor, ECM |
P205C | Reductant temperature sensor – circuit low | Wiring, reductant tank temperature sensor, ECM |
P205D | Reductant temperature sensor – circuit high | Wiring, reductant tank temperature sensor, ECM |
P205E | Reductant temperature sensor – circuit intermittent/erratic | Wiring, reductant tank temperature sensor, ECM |
P205F | Reductant system, bank 2 – performance problem | – |
P2060 | Reductant injection air pump – circuit low | Wiring short to earth, reductant injection air pump |
P2061 | Reductant injection air pump – circuit high | Wiring short to positive, reductant injection air pump |
P2062 | Reductant supply control – open circuit | Wiring |
P2063 | Reductant supply control – circuit low | Wiring |
P2064 | Reductant supply control – circuit high | Wiring |
P2065 | Fuel gauge tank sensor B – circuit malfunction | Wiring, fuel gauge tank sensor |
P2066 | Fuel gauge tank sensor B – performance problem | Wiring, fuel gauge tank sensor |
P2067 | Fuel gauge tank sensor B – circuit low | Wiring short to earth, fuel gauge tank sensor |
P2068 | Fuel gauge tank sensor B – circuit high | Wiring short to positive, fuel gauge tank sensor |
P2069 | Fuel gauge tank sensor B – circuit intermittent | Wiring, poor connection, fuel gauge tank sensor |
P206A | Reductant quality sensor – malfunction | Wiring, reductant quality sensor, ECM |
P206B | Reductant quality sensor – range/performance problem | Wiring, reductant quality sensor, ECM |
P206C | Reductant quality sensor – circuit low | Wiring, reductant quality sensor, ECM |
P206D | Reductant quality sensor – circuit high | Wiring, reductant quality sensor, ECM |
Intake manifold air control actuator, bank 2 – actuator stuck | ||
P206E | Wiring, intake manifold air control actuator, ECM | |
open | ||
Intake manifold air control actuator, bank 2 – actuator stuck | ||
P206F | Wiring, intake manifold air control actuator, ECM | |
closed | ||
Wiring, intake manifold air control actuator, mechanical | ||
P2070 | Intake manifold air control actuator – actuator stuck open | |
fault | ||
Wiring, intake manifold air control solenoid, mechanical | ||
P2070 | Intake manifold air control solenoid – solenoid stuck open | |
fault | ||
Wiring, intake manifold air control actuator, mechanical | ||
P2071 | Intake manifold air control actuator – actuator stuck closed | |
fault | ||
Wiring, intake manifold air control solenoid, mechanical | ||
P2071 | Intake manifold air control solenoid – solenoid stuck closed | |
fault | ||
P2072 | Throttle actuator control (TAC) system – actuator frozen | – |
Manifold absolute pressure (MAP) sensor/mass air flow (MAF) | ||
P2073 | Wiring, MAP sensor, MAF sensor | |
sensor – throttle position | ||
Manifold absolute pressure (MAP) sensor/mass air flow (MAF) | ||
P2074 | Wiring, MAP sensor, MAF sensor | |
sensor – throttle position | ||
Intake manifold air control actuator position sensor/switch – | Wiring, intake manifold air control actuator position | |
P2075 | ||
circuit malfunction | sensor/switch | |
Intake manifold air control actuator position sensor/switch – | Wiring, intake manifold air control actuator position | |
P2076 | ||
range/performance problem | sensor/switch | |
Intake manifold air control actuator position sensor/switch – | Wiring short to earth, intake manifold air control | |
P2077 | ||
circuit low | actuator position sensor/switch | |
Intake manifold air control actuator position sensor/switch – | Wiring short to positive, intake manifold air control | |
P2078 | ||
circuit high | actuator position sensor/switch | |
Intake manifold air control actuator position sensor/switch – | Wiring, poor connection, intake manifold air control | |
P2079 | ||
circuit intermittent | actuator position sensor/switch | |
Intake manifold air control actuator position sensor/switch, | Wiring, intake manifold air control actuator position | |
P207A | ||
bank 2 – circuit malfunction | sensor, ECM | |
Intake manifold air control actuator position sensor/switch, | Wiring, intake manifold air control actuator position | |
P207B | ||
bank 2 – circuit range/performance | sensor, ECM | |
Intake manifold air control actuator position sensor/switch, | Wiring, intake manifold air control actuator position | |
P207C | ||
bank 2 – circuit low | sensor, ECM | |
Intake manifold air control actuator position sensor/switch, | Wiring, intake manifold air control actuator position | |
P207D | ||
bank 2 – circuit high | sensor, ECM | |
Intake manifold air control actuator position sensor/switch, | Wiring, intake manifold air control actuator position | |
P207E | ||
bank 2 – circuit intermittent | sensor, ECM | |
P207F | Reductant quality – performance problem | – |
Exhaust gas temperature (EGT) sensor 1, bank 1 – | ||
P2080 | Wiring, EGT sensor | |
range/performance problem | ||
Exhaust gas temperature (EGT) sensor 1, bank 1 – circuit | ||
P2081 | Wiring, poor connection, EGT sensor | |
intermittent | ||
Exhaust gas temperature (EGT) sensor 1, bank 2 – | ||
P2082 | Wiring, EGT sensor | |
range/performance problem | ||
Exhaust gas temperature (EGT) sensor 1, bank 2 – circuit | ||
P2083 | Wiring, poor connection, EGT sensor | |
intermittent | ||
Exhaust gas temperature (EGT) sensor 2, bank 1 – | ||
P2084 | Wiring, EGT sensor | |
range/performance problem | ||
Exhaust gas temperature (EGT) sensor 2, bank 1 – circuit | ||
P2085 | Wiring, poor connection, EGT sensor | |
intermittent | ||
Exhaust gas temperature (EGT) sensor 2, bank 2 – | ||
P2086 | Wiring, EGT sensor | |
range/performance problem | ||
Exhaust gas temperature (EGT) sensor 2, bank 2 – circuit | ||
P2087 | Wiring, poor connection, EGT sensor | |
intermittent | ||
P2088 | Camshaft position (CMP) actuator A, bank 1 – circuit low | Wiring short to earth, CMP actuator |
P2089 | Camshaft position (CMP) actuator A, bank 1 – circuit high | Wiring short to positive, CMP actuator |
P208A | Reductant pump control – open circuit | Wiring, reductant pump, ECM |
P208B | Reductant pump control – range/performance problem | Wiring, reductant pump, ECM |
P208C | Reductant pump control – circuit low | Wiring, reductant pump, ECM |
P208D | Reductant pump control – circuit high | Wiring, reductant pump, ECM |
P208E | Reductant injector 1, bank 1 – injector stuck closed | Reductant injector |
P208F | Reductant injector 1, bank 2 – injector stuck closed | Wiring, reductant injector, ECM |
P2090 | Camshaft position (CMP) actuator B, bank 1 – circuit low | Wiring short to earth, CMP actuator |
P2091 | Camshaft position (CMP) actuator B, bank 1 – circuit high | Wiring short to positive, CMP actuator |
P2092 | Camshaft position (CMP) actuator A, bank 2 – circuit low | Wiring short to earth, CMP actuator |
P2093 | Camshaft position (CMP) actuator A, bank 2 – circuit high | Wiring short to positive, CMP actuator |
P2094 | Camshaft position (CMP) actuator B, bank 2 – circuit low | Wiring short to earth, CMP actuator |
P2095 | Camshaft position (CMP) actuator B, bank 2 – circuit high | Wiring short to positive, CMP actuator |
P2096 | Post catalytic converter fuel trim (FT), bank 1 – too lean | Catalytic converter, exhaust leak |
P2097 | Post catalytic converter fuel trim (FT), bank 1 – too rich | Catalytic converter |
P2098 | Post catalytic converter fuel trim (FT), bank 2 – too lean | Catalytic converter, exhaust leak |
P2099 | Post catalytic converter fuel trim (FT), bank 2 – too rich | Catalytic converter |
P209A | Reductant injection air pressure sensor B – circuit malfunction | Wiring, reductant injection air pressure sensor, ECM |
Reductant injection air pressure sensor B – circuit | ||
P209B | Wiring, reductant injection air pressure sensor, ECM | |
range/performance | ||
P209C | Reductant injection air pressure sensor B – circuit low | Wiring, reductant injection air pressure sensor, ECM |
P209D | Reductant injection air pressure sensor B – circuit high | Wiring, reductant injection air pressure sensor, ECM |
P209E | Reductant injection air pressure sensor A/B – correlation | Wiring, reductant injection air pressure sensor, ECM |
P209F | Reductant tank heater control – performance problem | Wiring, reductant tank heater, ECM |
P20A0 | Reductant purge control valve – open circuit | Wiring, reductant purge control valve, ECM |
P20A1 | Reductant purge control valve – performance problem | Wiring, reductant purge control valve, ECM |
P20A2 | Reductant purge control valve – circuit low | Wiring, reductant purge control valve, ECM |
P20A3 | Reductant purge control valve – circuit high | Wiring, reductant purge control valve, ECM |
P20A4 | Reductant purge control valve – valve stuck open | Wiring, reductant purge control valve, ECM |
P20A5 | Reductant purge control valve – valve stuck closed | Wiring, reductant purge control valve, ECM |
Wiring, reductant injection air pressure control valve, | ||
P20A6 | Reductant injection air pressure control valve – open circuit | |
ECM | ||
Reductant injection air pressure control valve – performance | Wiring, reductant injection air pressure control valve, | |
P20A7 | ||
problem | ECM | |
Wiring, reductant injection air pressure control valve, | ||
P20A8 | Reductant injection air pressure control valve – circuit low | |
ECM | ||
Wiring, reductant injection air pressure control valve, | ||
P20A9 | Reductant injection air pressure control valve – circuit high | |
ECM | ||
Reductant injection air pressure control valve – valve stuck | Wiring, reductant injection air pressure control valve, | |
P20AA | ||
open | ECM | |
Reductant injection air pressure control valve – valve stuck | Wiring, reductant injection air pressure control valve, | |
P20AB | ||
closed | ECM | |
Reductant metering unit temperature sensor – circuit | Wiring, reductant metering unit temperature sensor, | |
P20AC | ||
malfunction | ECM | |
Reductant metering unit temperature sensor – circuit | Wiring, reductant metering unit temperature sensor, | |
P20AD | ||
range/performance | ECM | |
Wiring, reductant metering unit temperature sensor, | ||
P20AE | Reductant metering unit temperature sensor – circuit low | |
ECM | ||
Wiring, reductant metering unit temperature sensor, | ||
P20AF | Reductant metering unit temperature sensor – circuit high | |
ECM | ||
Reductant metering unit temperature sensor – circuit | Wiring, reductant metering unit temperature sensor, | |
P20B0 | ||
intermittent/erratic | ECM | |
P20B1 | Reductant heater coolant control valve – open circuit | Wiring, reductant heater coolant control valve, ECM |
P20B2 | Reductant heater coolant control valve – performance problem | Wiring, reductant heater coolant control valve, ECM |
P20B3 | Reductant heater coolant control valve – circuit low | Wiring, reductant heater coolant control valve, ECM |
P20B4 | Reductant heater coolant control valve – circuit high | Wiring, reductant heater coolant control valve, ECM |
P20B5 | Reductant metering unit heater control – open circuit | Wiring, reductant heater, ECM |
P20B6 | Reductant metering unit heater – control performance problem | Wiring, reductant metering unit heater, ECM |
P20B7 | Reductant metering unit heater – control circuit low | Wiring, reductant metering unit heater, ECM |
P20B8 | Reductant metering unit heater control – circuit high | Wiring, reductant metering unit heater, ECM |
P20B9 | Reductant heater control A – open circuit | Wiring, reductant heater, ECM |
P20BA | Reductant heater control A – circuit performance problem | Wiring, reductant heater, ECM |
P20BB | Reductant heater control A – circuit low | Wiring, reductant heater, ECM |
P20BC | Reductant heater control A – circuit high | Wiring, reductant heater, ECM |
P20BD | Reductant heater control B – circuit open | Wiring, reductant heater, ECM |
P20BE | Reductant heater control B – performance problem | Wiring, reductant heater, ECM |
P20BF | Reductant heater control B – circuit low | Wiring, reductant heater, ECM |
P20C0 | Reductant heater control B – circuit high | Wiring, reductant heater, ECM |
P20C1 | Reductant heater control C – open circuit | Wiring, reductant heater, ECM |
P20C2 | Reductant heater control C – performance problem | Wiring, reductant heater, ECM |
P20C3 | Reductant heater control C – circuit low | Wiring, reductant heater, ECM |
P20C4 | Reductant heater control C – circuit high | Wiring, reductant heater, ECM |
P20C5 | Reductant heater control D – open circuit | Wiring, reductant heater, ECM |
P20C6 | Reductant heater control D – performance problem | Wiring, reductant heater, ECM |
P20C7 | Reductant heater control D – circuit low | Wiring, reductant heater, ECM |
P20C8 | Reductant heater control D – circuit high | Wiring, reductant heater, ECM |
P20C9 | Reductant control module – MIL activation requested | – |
P20CA | Reductant injection air pressure – leak | – |
P20CB | Exhaust after treatment fuel injector A – control circuit open | Wiring, exhaust after treatment fuel injector, ECM |
P20CC | Exhaust after treatment fuel injector A – performance problem | Wiring, exhaust after treatment fuel injector, ECM |
P20CD | Exhaust after treatment fuel injector A – control circuit low | Wiring, fuel injector, ECM |
P20CE | Exhaust after treatment fuel injector A – control circuit high | Wiring, fuel injector, ECM |
P20CF | Exhaust after treatment fuel injector A – injector stuck open | Wiring, exhaust after treatment fuel injector, ECM |
P20D0 | Exhaust after treatment fuel injector A – injector stuck closed | Wiring, exhaust after treatment fuel injector, ECM |
P20D1 | Exhaust after treatment fuel injector B – control circuit open | Wiring, exhaust after treatment fuel injector, ECM |
P20D2 | Exhaust after treatment fuel injector B – performance problem | Wiring, exhaust after treatment fuel injector, ECM |
P20D3 | Exhaust after treatment fuel injector B – control circuit low | Wiring, exhaust after treatment fuel injector, ECM |
P20D4 | Exhaust after treatment fuel injector B – control circuit high | Wiring, exhaust after treatment fuel injector, ECM |
P20D5 | Exhaust after treatment fuel injector B – injector stuck open | Wiring, exhaust after treatment fuel injector, ECM |
P20D6 | Exhaust after treatment fuel injector B – injector stuck closed | Wiring, exhaust after treatment fuel injector, ECM |
P20D7 | Exhaust after treatment fuel supply control – open circuit | – |
Exhaust after treatment fuel supply control – performance | ||
P20D8 | – | |
problem | ||
P20D9 | Exhaust after treatment fuel supply – control circuit low | – |
P20DA | Exhaust after treatment fuel supply – control circuit high | – |
P20DB | Exhaust after treatment fuel supply – control stuck open | – |
P20DC | Exhaust after treatment fuel supply control – valve stuck closed | – |
Exhaust after treatment fuel pressure sensor – circuit | Wiring, exhaust after treatment fuel pressure sensor, | |
P20DD | ||
malfunction | ECM | |
Exhaust after treatment fuel pressure sensor – circuit | Wiring, exhaust after treatment fuel pressure sensor, | |
P20DE | ||
range/performance | ECM | |
Wiring, exhaust after treatment fuel pressure sensor, | ||
P20DF | Exhaust after treatment fuel pressure sensor – circuit low | |
ECM | ||
Wiring, exhaust after treatment fuel pressure sensor, | ||
P20E0 | Exhaust after treatment fuel pressure sensor – circuit high | |
ECM | ||
Exhaust after treatment fuel pressure sensor – circuit | Wiring, exhaust after treatment fuel pressure sensor, | |
P20E1 | ||
intermittent/erratic | ECM | |
P20E2 | Exhaust gas temperature sensor 1/2, bank 1 – correlation | Wiring, exhaust gas temperature sensor, ECM |
P20E3 | Exhaust gas temperature sensor 1/3, bank 1 – correlation | Wiring, exhaust gas temperature sensor, ECM |
P20E4 | Exhaust gas temperature sensor 2/3, bank 1 – correlation | Wiring, exhaust gas temperature sensor, ECM |
P20E5 | Exhaust gas temperature sensor 1/2, bank 2 – correlation | Wiring, exhaust gas temperature sensor, ECM |
P20E6 | Reductant injection air pressure – pressure too low | – |
P20E7 | Reductant injection air pressure – pressure too high | – |
P20E8 | Reductant pressure – pressure too low | – |
P20E9 | Reductant pressure – pressure too high | – |
Reductant control module power relay – performance | ||
P20EA | – | |
malfunction | ||
Reductant control module power relay – performance | ||
P20EB | – | |
malfunction | ||
Nitrogen oxide (NOx) sensor, catalyst, bank 1 – over- | ||
P20EC | Wiring, NOx sensor, ECM | |
temperature condition | ||
Nitrogen oxide (NOx) sensor, pre-catalyst, bank 1 – over- | ||
P20ED | Wiring, NOx sensor, ECM | |
temperature condition | ||
Nitrogen oxide (NOx) sensor, catalyst, bank 1 – efficiency | ||
P20EE | Wiring, NOx sensor, ECM | |
below threshold | ||
Nitrogen oxide (NOx) sensor, pre-catalyst, bank 1 – efficiency | ||
P20EF | Wiring, NOx sensor, ECM | |
below threshold | ||
Nitrogen oxide (NOx) sensor, catalyst, bank 2 – over- | ||
P20F0 | Wiring, NOx sensor, ECM | |
temperature condition | ||
Nitrogen oxide (NOx) sensor, pre-catalyst, bank 2 – over- | ||
P20F1 | Wiring, NOx sensor, ECM | |
temperature condition | ||
Nitrogen oxide (NOx) sensor, catalyst, bank 2 – efficiency | ||
P20F2 | Wiring, NOx sensor, ECM | |
below threshold | ||
Nitrogen oxide (NOx) sensor, pre-catalyst, bank 2 – efficiency | ||
P20F3 | Wiring, NOx sensor, ECM | |
below threshold | ||
P20F4 | Reductant consumption – consumption low | – |
P20F5 | Reductant consumption – consumption high | – |
P20F6 | Reductant injector, unit 1, bank 1 – valve stuck open | – |
P20F7 | Reductant injector, unit 1, bank 2 – valve stuck open | – |
Intake manifold air control actuator, bank 1 – circuit | ||
P20F8 | Wiring, intake manifold air control actuator, ECM | |
performance | ||
Intake manifold air control actuator, bank 2 – circuit | ||
P20F9 | Wiring, intake manifold air control actuator, ECM | |
performance | ||
P20FA | Reductant pump B – open circuit | Wiring, reductant pump, ECM |
P20FB | Reductant pump B – range/performance problem | Wiring, reductant pump, ECM |
P20FC | Reductant pump B – control circuit low | Wiring, reductant pump, ECM |
P20FD | Reductant pump B – control circuit high | Wiring, reductant pump, ECM |
P2100 | Throttle actuator control (TAC) motor – open circuit | Wiring, TAC motor |
Throttle actuator control (TAC) motor – range/performance | ||
P2101 | Wiring, TAC motor | |
problem | ||
P2102 | Throttle actuator control (TAC) motor – circuit low | Wiring short to earth, TAC motor |
P2103 | Throttle actuator control (TAC) motor – circuit high | Wiring short to positive, TAC motor |
P2104 | Throttle actuator control (TAC) system – forced idle mode | Wiring, TAC motor, APP sensor, ECM |
Throttle actuator control (TAC) system – forced engine shut | ||
P2105 | Wiring, TAC motor, APP sensor, ECM | |
down mode | ||
Throttle actuator control (TAC) system – forced limited power | ||
P2106 | Wiring, TAC motor, APP sensor, ECM | |
mode | ||
P2107 | Throttle actuator control (TAC) control module – processor fault | TAC control module |
Throttle actuator control (TAC) control module – performance | ||
P2108 | TAC control module | |
problem | ||
Accelerator pedal position (APP) sensor A – minimum stop | ||
P2109 | APP sensor | |
performance | ||
P2109 | Throttle position (TP) sensor A – minimum stop performance | TP sensor, throttle valve tight/sticking |
P210A | Throttle control unit B, control motor – open circuit | Wiring, throttle control unit, ECM |
Throttle control unit B, control motor – circuit | ||
P210B | Wiring, throttle control unit, ECM | |
range/performance | ||
P210C | Throttle control unit B, control motor – circuit low | Wiring, throttle control unit, ECM |
P210D | Throttle control unit B, control motor – circuit high | Wiring, throttle control unit, ECM |
Throttle position sensor (TPS)/accelerator pedal position (APP) | ||
P210E | Wiring, TPS, APP sensor/switch, ECM | |
sensor/switch, C/F voltage – correlation | ||
P210F | Electronic throttle system (ETS) – forced limited rpm mode | Wiring, throttle motor, APP sensor, ECM |
Throttle actuator control (TAC) system – forced limited rpm | ||
P2110 | Wiring, TAC motor, APP sensor, ECM | |
mode | ||
P2111 | Throttle actuator control (TAC) system – actuator stuck open | Throttle body, throttle valve tight/sticking |
P2112 | Throttle actuator control (TAC) system – actuator stuck closed | Throttle body, throttle valve tight/sticking |
Accelerator pedal position (APP) sensor B – minimum stop | ||
P2113 | APP sensor | |
performance | ||
P2113 | Throttle position (TP) sensor B – minimum stop performance | TP sensor, throttle valve tight/sticking |
Accelerator pedal position (APP) sensor C – minimum stop | ||
P2114 | APP sensor | |
performance | ||
P2114 | Throttle position (TP) sensor C – minimum stop performance | TP sensor, throttle valve tight/sticking |
Accelerator pedal position (APP) sensor D – minimum stop | ||
P2115 | APP sensor | |
performance | ||
P2115 | Throttle position (TP) sensor D – minimum stop performance | TP sensor, throttle valve tight/sticking |
Accelerator pedal position (APP) sensor E – minimum stop | ||
P2116 | Wiring, APP sensor | |
performance | ||
P2116 | Throttle position (TP) sensor E – minimum stop performance | Wiring, TP sensor |
Accelerator pedal position (APP) sensor F – minimum stop | ||
P2117 | Wiring, APP sensor | |
performance | ||
P2117 | Throttle position (TP) sensor F – minimum stop performance | Wiring, TP sensor |
Throttle actuator control (TAC), throttle motor current – | ||
P2118 | Wiring, throttle motor | |
range/performance problem | ||
Throttle actuator control (TAC), throttle valve – | ||
P2119 | Throttle valve tight/sticking, throttle motor | |
range/performance problem | ||
P211A | Electronic throttle system (ETS) B – actuator stuck open | Throttle body, throttle valve tight/sticking |
P211B | Electronic throttle system (ETS) B – actuator stuck closed | Throttle body, throttle valve tight/sticking |
Electronic throttle system (ETS) B, throttle motor current – | ||
P211C | Wiring, throttle motor | |
range/performance problem | ||
Electronic throttle system (ETS) B, throttle body – | ||
P211D | Throttle valve tight/sticking, throttle motor | |
range/performance problem | ||
P211E | Electronic throttle system (ETS) B – processor fault | Wiring, throttle control unit, ECM |
P211F | Electronic throttle system (ETS) B – performance problem | Wiring, throttle control unit, ECM |
Accelerator pedal position (APP) sensor/switch D – circuit | ||
P2120 | Wiring, APP sensor/switch | |
malfunction | ||
P2120 | Throttle position (TP) sensor/switch D – circuit malfunction | Wiring, TP sensor/switch |
Accelerator pedal position (APP) sensor/switch D – | ||
P2121 | Wiring, APP sensor/switch | |
range/performance problem | ||
Throttle position (TP) sensor/switch D – range/performance | ||
P2121 | Wiring, TP sensor/switch | |
problem | ||
P2122 | Accelerator pedal position (APP) sensor/switch D – low input | Wiring short to earth, APP sensor/switch |
P2122 | Throttle position (TP) sensor/switch D – low input | Wiring short to earth, TP sensor/switch |
P2123 | Accelerator pedal position (APP) sensor/switch D – high input | Wiring short to positive, APP sensor/switch |
P2123 | Throttle position (TP) sensor/switch D – high input | Wiring short to positive, TP sensor/switch |
Accelerator pedal position (APP) sensor/switch D – circuit | ||
P2124 | Wiring, poor connection, APP sensor/switch | |
intermittent | ||
P2124 | Throttle position (TP) sensor/switch D – circuit intermittent | Wiring, poor connection, TP sensor/switch |
Accelerator pedal position (APP) sensor/switch E – circuit | ||
P2125 | Wiring, APP sensor/switch | |
malfunction | ||
P2125 | Throttle position (TP) sensor/switch E – circuit malfunction | Wiring, TP sensor/switch |
Accelerator pedal position (APP) sensor/switch E – | ||
P2126 | Wiring, APP sensor/switch | |
range/performance problem | ||
Throttle position (TP) sensor/switch E – range/performance | ||
P2126 | Wiring, TP sensor/switch | |
problem | ||
P2127 | Accelerator pedal position (APP) sensor/switch E – low input | Wiring short to earth, APP sensor/switch |
P2127 | Throttle position (TP) sensor/switch E – low input | Wiring short to earth, TP sensor/switch |
P2128 | Accelerator pedal position (APP) sensor/switch E – high input | Wiring short to positive, APP sensor/switch |
P2128 | Throttle position (TP) sensor/switch E – high input | Wiring short to positive, TP sensor/switch |
Accelerator pedal position (APP) sensor/switch E – circuit | ||
P2129 | Wiring, poor connection, APP sensor/switch | |
intermittent | ||
P2129 | Throttle position (TP) sensor/switch E – circuit intermittent | Wiring, poor connection, TP sensor/switch |
P212A | Throttle position (TP) sensor/switch G – circuit malfunction | Wiring, TP sensor/switch |
Throttle position (TP) sensor/switch G – range/performance | ||
P212B | Wiring, TP sensor/switch | |
problem | ||
P212C | Throttle position (TP) sensor/switch G – low input | Wiring, TP sensor/switch |
P212D | Throttle position (TP) sensor/switch G – high input | Wiring, TP sensor/switch |
P212E | Throttle position (TP) sensor/switch G – circuit intermittent | Wiring, TP sensor/switch |
P212F | Throttle position (TP) sensor/switch F/G – voltage correlation | Wiring, TP sensor/switch |
Accelerator pedal position (APP) sensor/switch F – circuit | ||
P2130 | Wiring, APP sensor/switch | |
malfunction | ||
P2130 | Throttle position (TP) sensor/switch F – circuit malfunction | Wiring, TP sensor/switch |
Accelerator pedal position (APP) sensor/switch F – circuit | ||
P2131 | Wiring, APP sensor/switch | |
range/performance | ||
Throttle position (TP) sensor/switch F – circuit | ||
P2131 | Wiring, TP sensor/switch | |
range/performance | ||
P2132 | Accelerator pedal position (APP) sensor/switch F – low input | Wiring short to earth, APP sensor/switch |
P2132 | Throttle position (TP) sensor/switch F – low input | Wiring short to earth, TP sensor/switch |
P2133 | Accelerator pedal position (APP) sensor/switch F – high input | Wiring short to positive, APP sensor/switch |
P2133 | Throttle position (TP) sensor/switch F – high input | Wiring short to positive, TP sensor/switch |
Accelerator pedal position (APP) sensor/switch F – circuit | ||
P2134 | Wiring, poor connection, APP sensor/switch | |
intermittent | ||
P2134 | Throttle position (TP) sensor/switch F – circuit intermittent | Wiring, poor connection, TP sensor/switch |
Accelerator pedal position (APP) sensor/switch A/B – voltage | ||
P2135 | Wiring, APP sensor/switch | |
correlation | ||
P2135 | Throttle position (TP) sensor/switch A/B – voltage correlation | Wiring, TP sensor/switch |
Accelerator pedal position (APP) sensor/switch A/C – voltage | ||
P2136 | Wiring, APP sensor/switch | |
correlation | ||
P2136 | Throttle position (TP) sensor/switch A/C – voltage correlation | Wiring, TP sensor/switch |
Accelerator pedal position (APP) sensor/switch B/C – voltage | ||
P2137 | Wiring, APP sensor/switch | |
correlation | ||
P2137 | Throttle position (TP) sensor/switch B/C – voltage correlation | Wiring, TP sensor/switch |
Accelerator pedal position (APP) sensor/switch D/E – voltage | ||
P2138 | Wiring, APP sensor/switch | |
correlation | ||
P2138 | Throttle position (TP) sensor/switch D/E – voltage correlation | Wiring, TP sensor/switch |
Accelerator pedal position (APP) sensor/switch D/F – voltage | ||
P2139 | Wiring, APP sensor/switch | |
correlation | ||
P2139 | Throttle position (TP) sensor/switch D/F – voltage correlation | Wiring, TP sensor/switch |
P213A | Exhaust gas recirculation (EGR) throttle B – open circuit | Wiring, EGR throttle, ECM |
Exhaust gas recirculation (EGR) throttle B – control circuit | ||
P213B | Wiring, EGR throttle, ECM | |
range/performance | ||
P213C | Exhaust gas recirculation (EGR) throttle B – control circuit low | Wiring, EGR throttle, ECM |
P213D | Exhaust gas recirculation (EGR) throttle B – control circuit high | Wiring, EGR throttle, ECM |
P213E | Fuel injection system fault – forced engine shut-down mode | – |
P213F | Fuel pump (FP) system fault – forced engine shut-down mode | Wiring, FP, FP relay, ECM |
Accelerator pedal position (APP) sensor/switch E/F – voltage | ||
P2140 | Wiring, APP sensor/switch | |
correlation | ||
P2140 | Throttle position (TP) sensor/switch E/F – voltage correlation | Wiring, TP sensor/switch |
Exhaust gas recirculation (EGR) throttle control valve – circuit | ||
P2141 | Wiring short to earth, EGR throttle control valve | |
low | ||
Exhaust gas recirculation (EGR) throttle control valve – circuit | ||
P2142 | Wiring short to positive, EGR throttle control valve | |
high | ||
P2143 | Exhaust gas recirculation (EGR) vent control – open circuit | Wiring, EGR vent control |
P2144 | Exhaust gas recirculation (EGR) vent control – circuit low | Wiring short to earth, EGR vent control |
P2145 | Exhaust gas recirculation (EGR) vent control – circuit high | Wiring short to positive, EGR vent control |
P2146 | Injector – group A, supply voltage – open circuit | Wiring, engine control (EC) relay, injector |
P2147 | Injector – group A, supply voltage – circuit low | Wiring short to earth, engine control (EC) relay, injector |
Wiring short to positive, engine control (EC) relay, | ||
P2148 | Injector – group A, supply voltage – circuit high | |
injector | ||
P2149 | Injector – group B, supply voltage – open circuit | Wiring, engine control (EC) relay, injector |
P2150 | Injector – group B, supply voltage – circuit low | Wiring short to earth, engine control (EC) relay, injector |
Wiring short to positive, engine control (EC) relay, | ||
P2151 | Injector – group B, supply voltage – circuit high | |
injector | ||
P2152 | Injector – group C, supply voltage – open circuit | Wiring, engine control (EC) relay, injector |
P2153 | Injector – group C, supply voltage – circuit low | Wiring short to earth, engine control (EC) relay, injector |
Wiring short to positive, engine control (EC) relay, | ||
P2154 | Injector – group C, supply voltage – circuit high | |
injector | ||
P2155 | Injector – group D, supply voltage – open circuit | Wiring, engine control (EC) relay, injector |
P2156 | Injector – group D, supply voltage – circuit low | Wiring short to earth, engine control (EC) relay, injector |
Wiring short to positive, engine control (EC) relay, | ||
P2157 | Injector – group D, supply voltage – circuit high | |
injector | ||
P2158 | Vehicle speed sensor (VSS) B – circuit malfunction | Wiring, VSS |
P2159 | Vehicle speed sensor (VSS) B – range/performance problem | Wiring, VSS |
Wiring, VSS, wheel speed sensor, incorrect tyre size, | ||
P215A | Vehicle speed sensor (VSS)/wheel speed – correlation | |
ECM | ||
Vehicle speed sensor (VSS)/transmission output shaft speed | Wiring, VSS, OSS sensor, transmission mechanical | |
P215B | ||
(OSS) sensor – correlation | fault, incorrect tyre size, ECM | |
Vehicle speed sensor (VSS)/output shaft speed (OSS) sensor | Wiring, VSS, OSS sensor, transmission mechanical | |
P215C | ||
– correlation | fault, incorrect tyre size, ECM | |
P2160 | Vehicle speed sensor (VSS) B – circuit low | Wiring short to earth, VSS |
P2161 | Vehicle speed sensor (VSS) B – circuit intermittent/erratic | Wiring, poor connection, VSS |
P2162 | Vehicle speed sensor (VSS) A/B – correlation | Wiring, VSS, incorrect tyre size |
Accelerator pedal position (APP) sensor A – maximum stop | ||
P2163 | Wiring, APP sensor | |
performance | ||
P2163 | Throttle position (TP) sensor A – maximum stop performance | Wiring, TP sensor |
Accelerator pedal position (APP) sensor B – maximum stop | ||
P2164 | Wiring, APP sensor | |
performance | ||
P2164 | Throttle position (TP) sensor B – maximum stop performance | Wiring, TP sensor |
Accelerator pedal position (APP) sensor C – maximum stop | ||
P2165 | Wiring, APP sensor | |
performance | ||
P2165 | Throttle position (TP) sensor C – maximum stop performance | Wiring, TP sensor |
Accelerator pedal position (APP) sensor D – maximum stop | ||
P2166 | Wiring, APP sensor | |
performance | ||
P2166 | Throttle position (TP) sensor D – maximum stop performance | Wiring, TP sensor |
Accelerator pedal position (APP) sensor E – maximum stop | ||
P2167 | Wiring, APP sensor | |
performance | ||
P2167 | Throttle position (TP) sensor E – maximum stop performance | Wiring, TP sensor |
Accelerator pedal position (APP) sensor F – maximum stop | ||
P2168 | Wiring, APP sensor | |
performance | ||
P2168 | Throttle position (TP) sensor F – maximum stop performance | Wiring, TP sensor |
P2169 | Exhaust gas pressure regulator vent solenoid – circuit open | Wiring, exhaust gas pressure regulator vent solenoid |
P216A | Fuel injector group E, supply voltage – open circuit | Wiring, engine control (EC) relay, injectors, ECM |
P216B | Fuel injector group E, supply voltage – circuit low | Wiring, engine control (EC) relay, injectors, ECM |
P216C | Fuel injector group E, supply voltage – circuit high | Wiring, engine control (EC) relay, injectors, ECM |
P216D | Fuel injector group F, supply voltage – open circuit | Wiring, engine control (EC) relay, injectors, ECM |
P216E | Fuel injector group F, supply voltage – circuit low | Wiring, engine control (EC) relay, injectors, ECM |
P216F | Fuel injector group F, supply voltage – circuit high | Wiring, engine control (EC) relay, injectors, ECM |
Wiring short to earth, exhaust gas pressure regulator | ||
P2170 | Exhaust gas pressure regulator vent solenoid – circuit low | |
vent solenoid | ||
Wiring short to positive, exhaust gas pressure regulator | ||
P2171 | Exhaust gas pressure regulator vent solenoid – circuit high | |
vent solenoid | ||
Throttle actuator control (TAC) system – sudden high airflow | ||
P2172 | Intake system, throttle body | |
detected | ||
P2173 | Throttle actuator control (TAC) system – high airflow detected | Intake system, throttle body |
Throttle actuator control (TAC) system – sudden low airflow | ||
P2174 | Intake system, throttle body | |
detected | ||
P2175 | Throttle actuator control (TAC) system – low airflow detected | Intake system, throttle body |
Throttle actuator control (TAC) system – idle position not | ||
P2176 | Basic setting not carried out | |
learned | ||
P2177 | System too lean off idle, bank 1 | Fuel pressure, injectors, intake leak |
P2178 | System too rich off idle, bank 1 | Fuel pressure, injectors, air intake restricted |
P2179 | System too lean off idle, bank 2 | Fuel pressure, injectors, intake leak |
P217A | Fuel injector group G, supply voltage – open circuit | Wiring, engine control (EC) relay, injectors, ECM |
P217B | Fuel injector group G, supply voltage – circuit low | Wiring, engine control (EC) relay, injectors, ECM |
P217C | Fuel injector group G, supply voltage – circuit high | Wiring, engine control (EC) relay, injectors, ECM |
P217D | Fuel injector group H, supply voltage – open circuit | Wiring, engine control (EC) relay, injectors, ECM |
P217E | Fuel injector group H, supply voltage – circuit low | Wiring, engine control (EC) relay, injectors, ECM |
P217F | Fuel injector group H, supply voltage – circuit high | Wiring, engine control (EC) relay, injectors, ECM |
P2180 | System too rich off idle, bank 2 | Fuel pressure, injectors, air intake restricted |
Radiator, coolant thermostat, engine coolant blower | ||
P2181 | Cooling system performance | |
motor | ||
Engine coolant temperature (ECT) sensor 2 – circuit | ||
P2182 | Wiring, ECT sensor | |
malfunction | ||
Engine coolant temperature (ECT) sensor 2 – | ||
P2183 | Wiring, ECT sensor | |
range/performance problem | ||
P2184 | Engine coolant temperature (ECT) sensor 2 – circuit low | Wiring short to earth, ECT sensor |
P2185 | Engine coolant temperature (ECT) sensor 2 – circuit high | Wiring short to positive, ECT sensor |
Engine coolant temperature (ECT) sensor 2 – circuit | ||
P2186 | Wiring, poor connection, ECT sensor | |
intermittent/erratic | ||
P2187 | System too lean at idle, bank 1 | Fuel pressure, injectors, intake leak |
P2188 | System too rich at idle, bank 1 | Fuel pressure, injectors, air intake restricted |
P2189 | System too lean at idle, bank 2 | Fuel pressure, injectors, intake leak |
P218A | Electronic throttle system (ETS) B – idle position not learned | Basic setting not carried out |
P218B | Throttle/fuel inhibit B – circuit malfunction | Wiring |
P218C | Throttle/fuel inhibit B – circuit range/performance | Wiring |
P218D | Throttle/fuel inhibit B – circuit low | Wiring |
P218E | Throttle/fuel inhibit B – circuit high | Wiring |
P2190 | System too rich at idle, bank 2 | Fuel pressure, injectors, air intake restricted |
P2191 | System too lean at higher load, bank 1 | Fuel pressure, injectors, intake leak |
P2192 | System too rich at higher load, bank 1 | Fuel pressure, injectors, air intake restricted |
P2193 | System too lean at higher load, bank 2 | Fuel pressure, injectors, intake leak |
P2194 | System too rich at higher load, bank 2 | Fuel pressure, injectors, air intake restricted |
P2195 | Heated oxygen sensor (HO2S) 1, bank 1 – signal stuck lean | HO2S, fuel pressure, injectors, intake leak |
P2195 | Oxygen sensor (O2S) 1, bank 1 – signal stuck lean | O2S, fuel pressure, injectors, intake leak |
P2196 | Heated oxygen sensor (HO2S) 1, bank 1 – signal stuck rich | HO2S, fuel pressure, injectors, air intake restricted |
P2196 | Oxygen sensor (O2S) 1, bank 1 – signal stuck rich | O2S, fuel pressure, injectors, air intake restricted |
P2197 | Heated oxygen sensor (HO2S) 1, bank 2 – signal stuck lean | HO2S, fuel pressure, injectors, intake leak |
P2197 | Oxygen sensor (O2S) 1, bank 2 – signal stuck lean | O2S, fuel pressure, injectors, intake leak |
P2198 | Heated oxygen sensor (HO2S) 1, bank 2 – signal stuck rich | HO2S, fuel pressure, injectors, air intake restricted |
P2198 | Oxygen sensor (O2S) 1, bank 2 – signal stuck rich | O2S, fuel pressure, injectors, air intake restricted |
P2199 | Intake air temperature (IAT) sensor 1/2 – correlation | Wiring, IAT sensor |
P219A | Mixture control, bank 1 – value out of range | – |
P219B | Mixture control, bank 2 – value out of range | – |
P219C | Mixture control, cylinder 1 – value out of range | – |
P219D | Mixture control, cylinder 2 – value out of range | – |
P219E | Mixture control, cylinder 3 – value out of range | – |
P219F | Mixture control, cylinder 4 – value out of range | – |
P21A0 | Mixture control, cylinder 5 – value out of range | – |
P21A1 | Mixture control, cylinder 6 – value out of range | – |
P21A2 | Mixture control, cylinder 7 – value out of range | – |
P21A3 | Mixture control, cylinder 8 – value out of range | – |
P21A4 | Mixture control, cylinder 9 – value out of range | – |
P21A5 | Mixture control, cylinder 10 – value out of range | – |
P21A6 | Mixture control, cylinder 11 – value out of range | – |
P21A7 | Mixture control, cylinder 12 – value out of range | – |
P2200 | Nitrogen oxides (NOx) sensor, bank 1 – circuit malfunction | Wiring, NOx sensor |
Nitrogen oxides (NOx) sensor, bank 1 – range/performance | ||
P2201 | Wiring, NOx sensor | |
problem | ||
P2202 | Nitrogen oxides (NOx) sensor, bank 1 – low input | Wiring short to earth, NOx sensor |
P2203 | Nitrogen oxides (NOx) sensor, bank 1 – high input | Wiring short to positive, NOx sensor |
P2204 | Nitrogen oxides (NOx) sensor, bank 1 – intermittent input | Wiring, poor connection, NOx sensor |
Nitrogen oxides (NOx) sensor, bank 1, heater control – open | ||
P2205 | Wiring, NOx sensor | |
circuit | ||
Nitrogen oxides (NOx) sensor, bank 1, heater control – circuit | ||
P2206 | Wiring short to earth, NOx sensor | |
low | ||
Nitrogen oxides (NOx) sensor, bank 1, heater control – circuit | ||
P2207 | Wiring short to positive, NOx sensor | |
high | ||
Nitrogen oxides (NOx) sensor, bank 1, heater sense circuit – | ||
P2208 | Wiring, NOx sensor | |
malfunction | ||
Nitrogen oxides (NOx) sensor, bank 1, heater sense circuit – | ||
P2209 | Wiring, NOx sensor | |
range/performance problem | ||
Nitrogen oxides (NOx) sensor 1, bank 1 – supply voltage circuit | ||
P220A | Wiring, NOx sensor | |
malfunction | ||
Nitrogen oxides (NOx) sensor 2, bank 1 – supply voltage circuit | ||
P220B | Wiring, NOx sensor | |
malfunction | ||
Nitrogen oxides (NOx) sensor 1, bank 2 – supply voltage circuit | ||
P220C | Wiring, NOx sensor | |
malfunction | ||
Nitrogen oxides (NOx) sensor 2, bank 2 – supply voltage circuit | ||
P220D | Wiring, NOx sensor | |
malfunction | ||
Nitrogen oxides (NOx) sensor, bank 1, heater sense circuit – | ||
P2210 | Wiring short to earth, NOx sensor | |
low input | ||
Nitrogen oxides (NOx) sensor, bank 1, heater sense circuit – | ||
P2211 | Wiring short to positive, NOx sensor | |
high input | ||
Nitrogen oxides (NOx) sensor, bank 1, heater sense circuit – | ||
P2212 | Wiring, poor connection, NOx sensor | |
circuit intermittent | ||
P2213 | Nitrogen oxides (NOx) sensor, bank 2 – circuit malfunction | Wiring, NOx sensor |
Nitrogen oxides (NOx) sensor, bank 2 – range/performance | ||
P2214 | Wiring, NOx sensor | |
problem | ||
P2215 | Nitrogen oxides (NOx) sensor, bank 2 – low input | Wiring short to earth, NOx sensor |
P2216 | Nitrogen oxides (NOx) sensor, bank 2 – high input | Wiring short to positive, NOx sensor |
P2217 | Nitrogen oxides (NOx) sensor, bank 2 – intermittent input | Wiring, poor connection, NOx sensor |
Nitrogen oxides (NOx) sensor, bank 2, heater control – open | ||
P2218 | Wiring, NOx sensor | |
circuit | ||
Nitrogen oxides (NOx) sensor, bank 2, heater control – circuit | ||
P2219 | Wiring short to earth, NOx sensor | |
low | ||
Nitrogen oxides (NOx) sensor, bank 2, heater control – circuit | ||
P2220 | Wiring short to positive, NOx sensor | |
high | ||
Nitrogen oxides (NOx) sensor, bank 2, heater sense circuit – | ||
P2221 | Wiring, NOx sensor | |
circuit malfunction | ||
Nitrogen oxides (NOx) sensor, bank 2, heater sense circuit – | ||
P2222 | Wiring, NOx sensor | |
range/performance problem | ||
Nitrogen oxides (NOx) sensor, bank 2, heater sense circuit – | ||
P2223 | Wiring short to earth, NOx sensor | |
circuit low | ||
Nitrogen oxides (NOx) sensor, bank 2, heater sense circuit – | ||
P2224 | Wiring short to positive, NOx sensor | |
circuit high | ||
Nitrogen oxides (NOx) sensor, bank 2, heater sense circuit – | ||
P2225 | Wiring, poor connection, NOx sensor | |
circuit intermittent | ||
P2226 | Barometric pressure (BARO) sensor – circuit malfunction | Wiring, BARO sensor |
Barometric pressure (BARO) sensor – range/performance | ||
P2227 | Wiring, BARO sensor | |
problem | ||
P2228 | Barometric pressure (BARO) sensor – circuit low | Wiring short to earth, BARO sensor |
P2229 | Barometric pressure (BARO) sensor – circuit high | Wiring short to positive, BARO sensor |
P222A | Barometric pressure (BARO) sensor B – circuit malfunction | Wiring, BARO sensor |
Barometric pressure (BARO) sensor B – circuit | ||
P222B | Wiring, BARO sensor | |
range/performance | ||
P222C | Barometric pressure (BARO) sensor B – circuit low | Wiring, BARO sensor |
P222D | Barometric pressure (BARO) sensor B – circuit high | Wiring, BARO sensor |
P222E | Barometric pressure (BARO) sensor B – circuit intermittent | Wiring, BARO sensor |
P222F | Barometric pressure (BARO) sensor A/B – correlation | Wiring, BARO sensor |
P2230 | Barometric pressure (BARO) sensor – circuit intermittent | Wiring, poor connection, BARO sensor |
Heated oxygen sensor (HO2S) 1, bank 1 – signal circuit | ||
P2231 | Wiring, HO2S | |
shorted to heater circuit | ||
Heated oxygen sensor (HO2S) 2, bank 1 – signal circuit | ||
P2232 | Wiring, HO2S | |
shorted to heater circuit | ||
Heated oxygen sensor (HO2S) 3, bank 1 – signal circuit | ||
P2233 | Wiring, HO2S | |
shorted to heater circuit | ||
Heated oxygen sensor (HO2S) 1, bank 2 – signal circuit | ||
P2234 | Wiring, HO2S | |
shorted to heater circuit | ||
Heated oxygen sensor (HO2S) 2, bank 2 – signal circuit | ||
P2235 | Wiring, HO2S | |
shorted to heater circuit | ||
Heated oxygen sensor (HO2S) 3, bank 2 – signal circuit | ||
P2236 | Wiring, HO2S | |
shorted to heater circuit | ||
Heated oxygen sensor (HO2S) 1, bank 1, positive current | ||
P2237 | Wiring, HO2S | |
control – open circuit | ||
Oxygen sensor (O2S) 1, bank 1, positive current control – open | ||
P2237 | Wiring, O2S | |
circuit | ||
Heated oxygen sensor (HO2S) 1, bank 1, positive current | ||
P2238 | Wiring short to earth, HO2S | |
control – circuit low | ||
Oxygen sensor (O2S) 1, bank 1, positive current control – | ||
P2238 | Wiring short to earth, O2S | |
circuit low | ||
Heated oxygen sensor (HO2S) 1, bank 1, positive current | ||
P2239 | Wiring short to positive, HO2S | |
control – circuit high | ||
Oxygen sensor (O2S) 1, bank 1, positive current control – | ||
P2239 | Wiring short to positive, O2S | |
circuit high | ||
Heated oxygen sensor (HO2S) 1, bank 2, positive current | ||
P2240 | Wiring, HO2S | |
control – open circuit | ||
Oxygen sensor (O2S) 1, bank 2, positive current control – open | ||
P2240 | Wiring, O2S | |
circuit | ||
Heated oxygen sensor (HO2S) 1, bank 2, positive current | ||
P2241 | Wiring short to earth, HO2S | |
control – circuit low | ||
Oxygen sensor (O2S) 1, bank 2, positive current control – | ||
P2241 | Wiring short to earth, O2S | |
circuit low | ||
Heated oxygen sensor (HO2S) 1, bank 2, positive current | ||
P2242 | Wiring short to positive, HO2S | |
control – circuit high | ||
Oxygen sensor (O2S) 1, bank 2, positive current control – | ||
P2242 | Wiring short to positive, O2S | |
circuit high | ||
Heated oxygen sensor (HO2S) 1, bank 1, reference voltage – | ||
P2243 | Wiring, HO2S | |
open circuit | ||
Oxygen sensor (O2S) 1, bank 1, reference voltage – open | ||
P2243 | Wiring, O2S | |
circuit | ||
Heated oxygen sensor (HO2S) 1, bank 1, reference voltage – | ||
P2244 | Wiring, HO2S | |
performance problem | ||
Oxygen sensor (O2S) 1, bank 1, reference voltage – | ||
P2244 | Wiring, O2S | |
performance problem | ||
Heated oxygen sensor (HO2S) 1, bank 1, reference voltage – | ||
P2245 | Wiring short to earth, HO2S | |
circuit low | ||
P2245 | Oxygen sensor (O2S) 1, bank 1, reference voltage – circuit low | Wiring short to earth, O2S |
Heated oxygen sensor (HO2S) 1, bank 1, reference voltage – | ||
P2246 | Wiring short to positive, HO2S | |
circuit high | ||
Oxygen sensor (O2S) 1, bank 1, reference voltage – circuit | ||
P2246 | Wiring short to positive, O2S | |
high | ||
Heated oxygen sensor (HO2S) 1, bank 2, reference voltage – | ||
P2247 | Wiring, HO2S | |
open circuit | ||
Oxygen sensor (O2S) 1, bank 2, reference voltage – open | ||
P2247 | Wiring, O2S | |
circuit | ||
Heated oxygen sensor (HO2S) 1, bank 2, reference voltage – | ||
P2248 | Wiring, HO2S | |
performance problem | ||
Oxygen sensor (O2S) 1, bank 2, reference voltage – | ||
P2248 | Wiring, O2S | |
performance problem | ||
Heated oxygen sensor (HO2S) 1, bank 2, reference voltage – | ||
P2249 | Wiring short to earth, HO2S | |
circuit low | ||
P2249 | Oxygen sensor (O2S) 1, bank 2, reference voltage – circuit low | Wiring short to earth, O2S |
Heated oxygen sensor (HO2S) 1, bank 2, reference voltage – | ||
P2250 | Wiring short to positive, HO2S | |
circuit high | ||
Oxygen sensor (O2S) 1, bank 2, reference voltage – circuit | ||
P2250 | Wiring short to positive, O2S | |
high | ||
Heated oxygen sensor (HO2S) 1, bank 1, negative current | ||
P2251 | Wiring, HO2S | |
control – open circuit | ||
Oxygen sensor (O2S) 1, bank 1, negative current control – | ||
P2251 | Wiring, O2S | |
open circuit | ||
Heated oxygen sensor (HO2S) 1, bank 1, negative current | ||
P2252 | Wiring short to earth, HO2S | |
control – circuit low | ||
Oxygen sensor (O2S) 1, bank 1, negative current control – | ||
P2252 | Wiring short to earth, O2S | |
circuit low | ||
Heated oxygen sensor (HO2S) 1, bank 1, negative current | ||
P2253 | Wiring short to positive, HO2S | |
control – circuit high | ||
Oxygen sensor (O2S) 1, bank 1, negative current control – | ||
P2253 | Wiring short to positive, O2S | |
circuit high | ||
Heated oxygen sensor (HO2S) 1, bank 2, negative current | ||
P2254 | Wiring, HO2S | |
control – open circuit | ||
Oxygen sensor (O2S) 1, bank 2, negative current control – | ||
P2254 | Wiring, O2S | |
open circuit | ||
Heated oxygen sensor (HO2S) 1, bank 2, negative current | ||
P2255 | Wiring short to earth, HO2S | |
control – circuit low | ||
Oxygen sensor (O2S) 1, bank 2, negative current control – | ||
P2255 | Wiring short to earth, O2S | |
circuit low | ||
Heated oxygen sensor (HO2S) 1, bank 2, negative current | ||
P2256 | Wiring short to positive, HO2S | |
control – circuit high | ||
Oxygen sensor (O2S) 1, bank 2, negative current control – | ||
P2256 | Wiring short to positive, O2S | |
circuit high | ||
Wiring short to earth, AIR pump relay, AIR pump, AIR | ||
P2257 | Secondary air injection (AIR) system, control A – circuit low | |
solenoid | ||
Wiring short to positive, AIR pump relay, AIR pump, | ||
P2258 | Secondary air injection (AIR) system, control A – circuit high | |
AIR solenoid | ||
Wiring short to earth, AIR pump relay, AIR pump, AIR | ||
P2259 | Secondary air injection (AIR) system, control B – circuit low | |
solenoid | ||
Wiring short to positive, AIR pump relay, AIR pump, | ||
P2260 | Secondary air injection (AIR) system, control B – circuit high | |
AIR solenoid | ||
Turbocharger (TC) bypass valve/supercharger (SC) bypass | ||
P2261 | Mechanical fault | |
valve | ||
P2262 | Turbocharger (TC) boost pressure not detected | Mechanical fault |
Turbocharger (TC) boost pressure/supercharger (SC) boost | ||
P2263 | Mechanical fault | |
pressure – performance problem | ||
P2264 | Fuel/water separator sensor – circuit malfunction | Wiring, fuel/water separator sensor |
P2265 | Fuel/water separator sensor – range/performance problem | Wiring, fuel/water separator sensor |
P2266 | Fuel/water separator sensor – circuit low | Wiring short to earth, fuel/water separator sensor |
P2267 | Fuel/water separator sensor – circuit high | Wiring short to positive, fuel/water separator sensor |
P2268 | Fuel/water separator sensor – circuit intermittent | Wiring, poor connection, fuel/water separator sensor |
P2269 | Water in fuel | Water in fuel |
P226A | Water-in-fuel warning lamp – circuit malfunction | Wiring, warning lamp, ECM |
Turbocharger (TC)/supercharger (SC) boost pressure – | ||
P226B | Mechanical | |
pressure too high | ||
P226C | Turbocharger (TC) boost pressure control A – slow response | – |
P226F | Turbocharger (TC) boost pressure control B – slow response | – |
P2270 | Heated oxygen sensor (HO2S) 2, bank 1 – signal stuck lean | Wiring, HO2S, fuel pressure, injectors, intake leak |
P2270 | Oxygen sensor (O2S) 2, bank 1 – signal stuck lean | Wiring, O2S, fuel pressure, injectors, intake leak |
Wiring, HO2S, fuel pressure, injectors, air intake | ||
P2271 | Heated oxygen sensor (HO2S) 2, bank 1 – signal stuck rich | |
restricted | ||
Wiring, O2S, fuel pressure, injectors, air intake | ||
P2271 | Oxygen sensor (O2S) 2, bank 1 – signal stuck rich | |
restricted | ||
P2272 | Heated oxygen sensor (HO2S) 2, bank 2 – signal stuck lean | Wiring, HO2S, fuel pressure, injectors, intake leak |
P2272 | Oxygen sensor (O2S) 2, bank 2 – signal stuck lean | Wiring, O2S, fuel pressure, injectors, intake leak |
Wiring, HO2S, fuel pressure, injectors, air intake | ||
P2273 | Heated oxygen sensor (HO2S) 2, bank 2 – signal stuck rich | |
restricted | ||
Wiring, O2S, fuel pressure, injectors, air intake | ||
P2273 | Oxygen sensor (O2S) 2, bank 2 – signal stuck rich | |
restricted | ||
P2274 | Heated oxygen sensor (HO2S) 3, bank 1 – signal stuck lean | Wiring, HO2S, fuel pressure, injectors, intake leak |
P2274 | Oxygen sensor (O2S) 3, bank 1 – signal stuck lean | Wiring, O2S, fuel pressure, injectors, intake leak |
Wiring, HO2S, fuel pressure, injectors, air intake | ||
P2275 | Heated oxygen sensor (HO2S) 3, bank 1 – signal stuck rich | |
restricted | ||
Wiring, O2S, fuel pressure, injectors, air intake | ||
P2275 | Oxygen sensor (O2S) 3, bank 1 – signal stuck rich | |
restricted | ||
P2276 | Heated oxygen sensor (HO2S) 3, bank 2 – signal stuck lean | Wiring, HO2S, fuel pressure, injectors, intake leak |
P2276 | Oxygen sensor (O2S) 3, bank 2 – signal stuck lean | Wiring, O2S, fuel pressure, injectors, intake leak |
Wiring, HO2S, fuel pressure, injectors, air intake | ||
P2277 | Heated oxygen sensor (HO2S) 3, bank 2 – signal stuck rich | |
restricted | ||
Wiring, O2S, fuel pressure, injectors, air intake | ||
P2277 | Oxygen sensor (O2S) 3, bank 2 – signal stuck rich | |
restricted | ||
Heated oxygen sensor (HO2S) 3, bank 1/heated oxygen | ||
P2278 | Wiring | |
sensor (HO2S) 3, bank 2 – signals transposed | ||
Oxygen sensor (O2S) 3, bank 1/oxygen sensor (O2S) 3, bank | ||
P2278 | Wiring | |
2 – signals transposed | ||
P2279 | Intake air leak | Mechanical fault |
P2280 | Air leak/blockage between air filter and MAF sensor | Mechanical fault |
P2281 | Air leak between MAF sensor and throttle body | Mechanical fault |
P2282 | Air leak between throttle body and intake valves | Mechanical fault |
P2283 | Injector control pressure sensor – circuit malfunction | Wiring, injector control pressure sensor |
P2284 | Injector control pressure sensor – range/performance problem | Wiring, injector control pressure sensor |
P2285 | Injector control pressure sensor – circuit low | Wiring short to earth, injector control pressure sensor |
P2286 | Injector control pressure sensor – circuit high | Wiring short to positive, injector control pressure sensor |
Wiring, poor connection, injector control pressure | ||
P2287 | Injector control pressure sensor – circuit intermittent | |
sensor | ||
Fuel pressure regulator, injector control pressure | ||
P2288 | Injector control pressure – pressure too high | |
sensor | ||
P2289 | Injector control pressure, engine off – pressure too high | Fuel pressure regulator |
P228A | Fuel pressure regulator 1 – limp-home mode activated | – |
P228B | Fuel pressure regulator 2 – limp-home mode activated | – |
Fuel pressure regulator 1, control limit exceeded – fuel | ||
P228C | Fuel pressure regulator, ECM | |
pressure low | ||
Fuel pressure regulator 1, control limit exceeded – fuel | ||
P228D | Fuel pressure regulator, ECM | |
pressure high | ||
Fuel pressure regulator 1, learning limit exceeded – signal too | ||
P228E | Wiring, fuel pressure regulator | |
low | ||
Fuel pressure regulator 1, learning limit exceeded – signal too | ||
P228F | Wiring, fuel pressure regulator | |
high | ||
Fuel pressure regulator, injector control pressure | ||
P2290 | Injector control pressure – pressure too low | |
sensor | ||
Fuel pressure regulator, injector control pressure | ||
P2291 | Injector control pressure, engine cranking – pressure too low | |
sensor | ||
Fuel pressure regulator, injector control pressure | ||
P2292 | Injector control pressure – erratic | |
sensor | ||
P2293 | Fuel pressure regulator 2 – performance problem | Wiring, fuel pressure regulator |
P2294 | Fuel pressure regulator 2 – circuit malfunction | Wiring, fuel pressure regulator |
P2295 | Fuel pressure regulator 2 – circuit low | Wiring short to earth, fuel pressure regulator |
P2296 | Fuel pressure regulator 2 – circuit high | Wiring short to positive, fuel pressure regulator |
Heated oxygen sensor (HO2S) 1, bank 1 – signal out of range | ||
P2297 | HO2S, intake leak, exhaust leak, injectors | |
during deceleration | ||
Oxygen sensor (O2S) 1, bank 1 – signal out of range during | ||
P2297 | O2S, intake leak, exhaust leak, injectors | |
deceleration | ||
Heated oxygen sensor (HO2S) 1, bank 2 – signal out of range | ||
P2298 | HO2S, intake leak, exhaust leak, injectors | |
during deceleration | ||
Oxygen sensor (O2S) 1, bank 2 – signal out of range during | ||
P2298 | O2S, intake leak, exhaust leak, injectors | |
deceleration | ||
Brake pedal position (BPP) switch/accelerator pedal position | ||
P2299 | Wiring, BPP switch, APP sensor | |
(APP) sensor – signals incompatible | ||
Fuel pressure regulator 2, control limit exceeded – fuel | ||
P229A | Fuel pressure regulator, ECM | |
pressure low | ||
Fuel pressure regulator 2, control limit exceeded – fuel | ||
P229B | Fuel pressure regulator, ECM | |
pressure high | ||
Fuel pressure regulator 2, learning limit exceeded – signal too | ||
P229C | Wiring, fuel pressure regulator | |
low | ||
Fuel pressure regulator 2, learning limit exceeded – signal too | ||
P229D | Wiring, fuel pressure regulator | |
high | ||
P229E | Nitrogen oxides (NOx) sensor 2, bank 1 – circuit malfunction | Wiring, NOx sensor |
Nitrogen oxides (NOx) sensor 2, bank 1 – circuit | ||
P229F | Wiring, NOx sensor | |
range/performance | ||
P22A0 | Nitrogen oxides (NOx) sensor 2, bank 1 – circuit low | Wiring, NOx sensor |
P22A1 | Nitrogen oxides (NOx) sensor 2, bank 1 – circuit high | Wiring, NOx sensor |
Nitrogen oxides (NOx) sensor 2, bank 1 – circuit | ||
P22A2 | Wiring, NOx sensor | |
intermittent/erratic | ||
Nitrogen oxides (NOx) sensor 2, bank 1 – circuit | ||
P22A2 | Wiring, NOx sensor | |
intermittent/erratic | ||
Nitrogen oxides (NOx) sensor 2, bank 1, heater control – open | ||
P22A3 | Wiring, NOx sensor | |
circuit | ||
Nitrogen oxides (NOx) sensor 2, bank 1, heater control – circuit | ||
P22A4 | Wiring, NOx sensor | |
low | ||
Nitrogen oxides (NOx) sensor 2, bank 1, heater control – circuit | ||
P22A5 | Wiring, NOx sensor | |
high | ||
Nitrogen oxides (NOx) sensor 2, bank 1, heater sense circuit – | ||
P22A6 | Wiring, NOx sensor | |
malfunction | ||
Nitrogen oxides (NOx) sensor 2, bank 1, heater sense circuit – | ||
P22A7 | Wiring, NOx sensor | |
range/performance problem | ||
Nitrogen oxides (NOx) sensor 2, bank 1, heater sense circuit – | ||
P22A8 | Wiring, NOx sensor | |
circuit low | ||
Nitrogen oxides (NOx) sensor 2, bank 1, heater sense circuit – | ||
P22A9 | Wiring, NOx sensor | |
circuit high | ||
Nitrogen oxides (NOx) sensor 2, bank 1, heater sense circuit – | ||
P22AA | Wiring, NOx sensor | |
circuit intermittent | ||
Heated oxygen sensor (HO2S) 2, bank 1, positive current | ||
P22AB | Wiring, HO2S | |
control – open circuit | ||
Heated oxygen sensor (HO2S) 2, bank 1, positive current | ||
P22AC | Wiring, HO2S | |
control – circuit low | ||
Heated oxygen sensor (HO2S) 2, bank 1, positive current | ||
P22AD | Wiring, HO2S | |
control – circuit high | ||
Heated oxygen sensor (HO2S) 2, bank 1, reference voltage – | ||
P22AE | Wiring, HO2S | |
open circuit | ||
Heated oxygen sensor (HO2S) 2, bank 1, reference voltage – | ||
P22AF | Wiring, HO2S | |
performance problem | ||
Heated oxygen sensor (HO2S) 2, bank 1, reference voltage – | ||
P22B0 | Wiring, HO2S | |
circuit low | ||
Heated oxygen sensor (HO2S) 2, bank 1, reference voltage – | ||
P22B1 | Wiring, HO2S | |
circuit high | ||
Heated oxygen sensor (HO2S) 2, bank 1, negative current | ||
P22B2 | Wiring, HO2S | |
control – open circuit | ||
Heated oxygen sensor (HO2S) 2, bank 1, negative current | ||
P22B3 | Wiring, HO2S | |
control – circuit low | ||
Heated oxygen sensor (HO2S) 2, bank 1, negative current | ||
P22B4 | Wiring, HO2S | |
control – circuit high | ||
Heated oxygen sensor (HO2S) 2, bank 1, pumping current trim | ||
P22B5 | Wiring, HO2S | |
– open circuit | ||
Heated oxygen sensor (HO2S) 2, bank 1, pumping current trim | ||
P22B6 | Wiring, HO2S | |
– circuit low | ||
Heated oxygen sensor (HO2S) 2, bank 1, pumping current trim | ||
P22B7 | Wiring, HO2S | |
– circuit high | ||
Heated oxygen sensor (HO2S) 2, bank 2, positive current | ||
P22B8 | Wiring, HO2S | |
control – open circuit | ||
Heated oxygen sensor (HO2S) 2, bank 2, positive current | ||
P22B9 | Wiring, HO2S | |
control – circuit low | ||
Heated oxygen sensor (HO2S) 2, bank 2, positive current | ||
P22BA | Wiring, HO2S | |
control – circuit high | ||
Heated oxygen sensor (HO2S) 2, bank 2, reference voltage – | ||
P22BB | Wiring, HO2S | |
open circuit | ||
Heated oxygen sensor (HO2S) 2, bank 2, reference voltage – | ||
P22BC | Wiring, HO2S | |
performance problem | ||
Heated oxygen sensor (HO2S) 2, bank 2, reference voltage – | ||
P22BD | Wiring, HO2S | |
circuit low | ||
Heated oxygen sensor (HO2S) 2, bank 2, reference voltage – | ||
P22BE | Wiring, HO2S | |
circuit high | ||
Heated oxygen sensor (HO2S) 2, bank 2, negative current | ||
P22BF | Wiring, HO2S | |
control – open circuit | ||
Heated oxygen sensor (HO2S) 2, bank 2, negative current | ||
P22C0 | Wiring, HO2S | |
control – circuit low | ||
Heated oxygen sensor (HO2S) 2, bank 2, negative current | ||
P22C1 | Wiring, HO2S | |
control – circuit high | ||
Heated oxygen sensor (HO2S) 2, bank 2, pumping current trim | ||
P22C2 | Wiring, HO2S | |
– open circuit | ||
Heated oxygen sensor (HO2S) 2, bank 2, pumping current trim | ||
P22C3 | Wiring, HO2S | |
– circuit low | ||
Heated oxygen sensor (HO2S) 2, bank 2, pumping current trim | ||
P22C4 | Wiring, HO2S | |
– circuit high | ||
P22C5 | Turbocharger (TC) outlet valve – control circuit open | Wiring, TC outlet valve |
P22C6 | Turbocharger (TC) outlet valve – control circuit low | Wiring, TC outlet valve |
P22C7 | Turbocharger (TC) outlet valve – control circuit high | Wiring, TC outlet valve |
P22C8 | Turbocharger (TC) outlet valve – valve stuck open | Wiring, TC outlet valve |
P22C9 | Turbocharger (TC) outlet valve – valve stuck closed | Wiring, TC outlet valve |
P22CA | Turbocharger (TC) outlet switching valve – control circuit open | Wiring, TC outlet switching valve |
P22CB | Turbocharger (TC) outlet switching valve – control circuit low | Wiring, TC outlet switching valve |
P22CC | Turbocharger (TC) outlet switching valve – control circuit high | Wiring, TC outlet switching valve |
P22CD | Turbocharger (TC) outlet switching valve – valve stuck open | Wiring, TC outlet switching valve |
P22CE | Turbocharger (TC) outlet switching valve – valve stuck closed | Wiring, TC outlet switching valve |
P22CF | Turbocharger (TC) inlet valve – control circuit open | Wiring, TC inlet valve |
P22D0 | Turbocharger (TC) inlet valve – control circuit low | Wiring, TC inlet valve |
P22D1 | Turbocharger (TC) inlet valve – control circuit high | Wiring, TC inlet valve |
P22D2 | Turbocharger (TC) inlet valve – valve stuck open | Wiring, TC inlet valve |
P22D3 | Turbocharger (TC) inlet valve – valve stuck closed | Wiring, TC inlet valve |
Turbocharger (TC) inlet valve position sensor – circuit | ||
P22D4 | Wiring, TC inlet valve position sensor | |
malfunction | ||
Turbocharger (TC) inlet valve position sensor – circuit | ||
P22D5 | Wiring, TC inlet valve position sensor | |
range/performance | ||
P22D6 | Turbocharger (TC) inlet valve position sensor – circuit low | Wiring, TC inlet valve position sensor |
P22D7 | Turbocharger (TC) inlet valve position sensor – circuit high | Wiring, TC inlet valve position sensor |
Turbocharger (TC) inlet valve position sensor – circuit | ||
P22D8 | Wiring, TC inlet valve position sensor | |
intermittent/erratic | ||
P2300 | Ignition coil A, primary circuit – circuit low | Wiring short to earth, ignition coil |
P2301 | Ignition coil A, primary circuit – circuit high | Wiring short to positive, ignition coil |
P2302 | Ignition coil A, secondary circuit – malfunction | Wiring, ignition coil |
P2303 | Ignition coil B, primary circuit – circuit low | Wiring short to earth, ignition coil |
P2304 | Ignition coil B, primary circuit – circuit high | Wiring short to positive, ignition coil |
P2305 | Ignition coil B, secondary circuit – malfunction | Wiring, ignition coil |
P2306 | Ignition coil C, primary circuit – circuit low | Wiring short to earth, ignition coil |
P2307 | Ignition coil C, primary circuit – circuit high | Wiring short to positive, ignition coil |
P2308 | Ignition coil C, secondary circuit – malfunction | Wiring, ignition coil |
P2309 | Ignition coil D, primary circuit – circuit low | Wiring short to earth, ignition coil |
P2310 | Ignition coil D, primary circuit – circuit high | Wiring short to positive, ignition coil |
P2311 | Ignition coil D, secondary circuit – malfunction | Wiring, ignition coil |
P2312 | Ignition coil E, primary circuit – circuit low | Wiring short to earth, ignition coil |
P2313 | Ignition coil E, primary circuit – circuit high | Wiring short to positive, ignition coil |
P2314 | Ignition coil E, secondary circuit – malfunction | Wiring, ignition coil |
P2315 | Ignition coil F, primary circuit – circuit low | Wiring short to earth, ignition coil |
P2316 | Ignition coil F, primary circuit – circuit high | Wiring short to positive, ignition coil |
P2317 | Ignition coil F, secondary circuit – malfunction | Wiring, ignition coil |
P2318 | Ignition coil G, primary circuit – circuit low | Wiring short to earth, ignition coil |
P2319 | Ignition coil G, primary circuit – circuit high | Wiring short to positive, ignition coil |
P2320 | Ignition coil G, secondary circuit – malfunction | Wiring, ignition coil |
P2321 | Ignition coil H, primary circuit – circuit low | Wiring short to earth, ignition coil |
P2322 | Ignition coil H, primary circuit – circuit high | Wiring short to positive, ignition coil |
P2323 | Ignition coil H, secondary circuit – malfunction | Wiring, ignition coil |
P2324 | Ignition coil I, primary circuit – circuit low | Wiring short to earth, ignition coil |
P2325 | Ignition coil I, primary circuit – circuit high | Wiring short to positive, ignition coil |
P2326 | Ignition coil I, secondary circuit – malfunction | Wiring, ignition coil |
P2327 | Ignition coil J, primary circuit – circuit low | Wiring short to earth, ignition coil |
P2328 | Ignition coil J, primary circuit – circuit high | Wiring short to positive, ignition coil |
P2329 | Ignition coil J, secondary circuit – malfunction | Wiring, ignition coil |
P2330 | Ignition coil K, primary circuit – circuit low | Wiring short to earth, ignition coil |
P2331 | Ignition coil K, primary circuit – circuit high | Wiring short to positive, ignition coil |
P2332 | Ignition coil K, secondary circuit – malfunction | Wiring, ignition coil |
P2333 | Ignition coil L, primary circuit – circuit low | Wiring short to earth, ignition coil |
P2334 | Ignition coil L, primary circuit – circuit high | Wiring short to positive, ignition coil |
P2335 | Ignition coil L, secondary circuit – malfunction | Wiring, ignition coil |
Ignition timing, knock sensor (KS), fuel quality, | ||
P2336 | Cylinder 1 – above knock threshold | |
mechanical fault | ||
Ignition timing, knock sensor (KS), fuel quality, | ||
P2337 | Cylinder 2 – above knock threshold | |
mechanical fault | ||
Ignition timing, knock sensor (KS), fuel quality, | ||
P2338 | Cylinder 3 – above knock threshold | |
mechanical fault | ||
Ignition timing, knock sensor (KS), fuel quality, | ||
P2339 | Cylinder 4 – above knock threshold | |
mechanical fault | ||
Ignition timing, knock sensor (KS), fuel quality, | ||
P2340 | Cylinder 5 – above knock threshold | |
mechanical fault | ||
Ignition timing, knock sensor (KS), fuel quality, | ||
P2341 | Cylinder 6 – above knock threshold | |
mechanical fault | ||
Ignition timing, knock sensor (KS), fuel quality, | ||
P2342 | Cylinder 7 – above knock threshold | |
mechanical fault | ||
Ignition timing, knock sensor (KS), fuel quality, | ||
P2343 | Cylinder 8 – above knock threshold | |
mechanical fault | ||
Ignition timing, knock sensor (KS), fuel quality, | ||
P2344 | Cylinder 9 – above knock threshold | |
mechanical fault | ||
Ignition timing, knock sensor (KS), fuel quality, | ||
P2345 | Cylinder 10 – above knock threshold | |
mechanical fault | ||
Ignition timing, knock sensor (KS), fuel quality, | ||
P2346 | Cylinder 11 – above knock threshold | |
mechanical fault | ||
Ignition timing, knock sensor (KS), fuel quality, | ||
P2347 | Cylinder 12 – above knock threshold | |
mechanical fault | ||
P2348 | Cylinder pressure sensor, cylinder 9 – circuit malfunction | Wiring, cylinder pressure sensor, ECM |
Cylinder pressure sensor, cylinder 9 – circuit | ||
P2349 | Wiring, cylinder pressure sensor, ECM | |
range/performance | ||
P234A | Cylinder pressure sensor, cylinder 9 – circuit low | Wiring, cylinder pressure sensor, ECM |
P234B | Cylinder pressure sensor, cylinder 9 – circuit high | Wiring, cylinder pressure sensor, ECM |
P234C | Cylinder pressure sensor, cylinder 9 – circuit intermittent/erratic | Wiring, cylinder pressure sensor, ECM |
P234D | Cylinder 9 – pressure too low | – |
P234E | Cylinder 9 – pressure too high | – |
P234F | Cylinder 9 – pressure variation low | – |
P2350 | Cylinder 9 – pressure variation high | – |
P2351 | Cylinder 9 – combustion performance | – |
P2352 | Cylinder pressure sensor, cylinder 10 – circuit malfunction | Wiring, cylinder pressure sensor, ECM |
Cylinder pressure sensor, cylinder 10 – circuit | ||
P2353 | Wiring, cylinder pressure sensor, ECM | |
range/performance | ||
P2354 | Cylinder pressure sensor, cylinder 10 – circuit low | Wiring, cylinder pressure sensor, ECM |
P2355 | Cylinder pressure sensor, cylinder 10 – circuit high | Wiring, cylinder pressure sensor, ECM |
Cylinder pressure sensor, cylinder 10 – circuit | ||
P2356 | Wiring, cylinder pressure sensor, ECM | |
intermittent/erratic | ||
P2357 | Cylinder 10 – pressure too low | – |
P2358 | Cylinder 10 – pressure too high | – |
P2359 | Cylinder 10 – pressure variation low | – |
P235A | Cylinder 10 – pressure variation high | – |
P235B | Cylinder 10 – combustion performance | – |
P235C | Cylinder pressure sensor, cylinder 11 – circuit malfunction | Wiring, cylinder pressure sensor, ECM |
Cylinder pressure sensor, cylinder 11 – circuit | ||
P235D | Wiring, cylinder pressure sensor, ECM | |
range/performance | ||
P235E | Cylinder pressure sensor, cylinder 11 – circuit low | Wiring, cylinder pressure sensor, ECM |
P235F | Cylinder pressure sensor, cylinder 11 – circuit high | Wiring, cylinder pressure sensor, ECM |
Cylinder pressure sensor, cylinder 11 – circuit | ||
P2360 | Wiring, cylinder pressure sensor, ECM | |
intermittent/erratic | ||
P2361 | Cylinder 11 – pressure too low | – |
P2362 | Cylinder 11 – pressure too high | – |
P2363 | Cylinder 11 – pressure variation low | – |
P2364 | Cylinder 11 – pressure variation high | – |
P2365 | Cylinder 11 – combustion performance | – |
P2366 | Cylinder pressure sensor, cylinder 12 – circuit malfunction | Wiring, cylinder pressure sensor, ECM |
Cylinder pressure sensor, cylinder 12 – circuit | ||
P2367 | Wiring, cylinder pressure sensor, ECM | |
range/performance | ||
P2368 | Cylinder pressure sensor, cylinder 12 – circuit low | Wiring, cylinder pressure sensor, ECM |
P2369 | Cylinder pressure sensor, cylinder 12 – circuit high | Wiring, cylinder pressure sensor, ECM |
Cylinder pressure sensor, cylinder 12 – circuit | ||
P236A | ||
intermittent/erratic | ||
P236B | Cylinder 12 – pressure too low | – |
P236C | Cylinder 12 – pressure too high | – |
P236D | Cylinder 12 – pressure variation low | – |
P236E | Cylinder 12 – pressure variation high | – |
P236F | Cylinder 12 – combustion performance | – |
Evaporative emission (EVAP) leak detection pump, control – | ||
P2400 | Wiring, EVAP leak detection pump | |
open circuit | ||
Evaporative emission (EVAP) leak detection pump, control – | ||
P2401 | ||
circuit low | ||
Evaporative emission (EVAP) leak detection pump, control – | ||
P2402 | ||
circuit high | ||
Evaporative emission (EVAP) leak detection pump, sense | ||
P2403 | Wiring, EVAP leak detection pump | |
circuit – open circuit | ||
Evaporative emission (EVAP) leak detection pump, sense | ||
P2404 | Wiring, EVAP leak detection pump | |
circuit – range/performance problem | ||
Evaporative emission (EVAP) leak detection pump, sense | ||
P2405 | ||
circuit – circuit low | ||
Evaporative emission (EVAP) leak detection pump, sense | ||
P2406 | ||
circuit – circuit high | ||
Evaporative emission (EVAP) leak detection pump, sense | ||
P2407 | ||
circuit – circuit intermittent/erratic | ||
P2408 | Fuel filler cap warning sensor/switch – circuit malfunction | |
Fuel filler cap warning sensor/switch – range/performance | ||
P2409 | ||
problem | ||
Evaporative emission (EVAP) leak detection pump heater – | ||
P240A | ||
open circuit | ||
Evaporative emission (EVAP) leak detection pump heater – | ||
P240B | ||
circuit low | ||
Evaporative emission (EVAP) leak detection pump heater – | ||
P240C | ||
circuit high | ||
P240F | Exhaust gas recirculation (EGR) system – slow response | – |
P2410 | Fuel filler cap warning sensor/switch – circuit low | |
sensor/switch | ||
P2411 | Fuel filler cap warning sensor/switch – circuit high | |
sensor/switch | ||
P2412 | Fuel filler cap warning sensor/switch – circuit intermittent/erratic | |
sensor/switch | ||
Exhaust gas recirculation (EGR) system – performance | ||
P2413 | ||
problem | ||
Heated oxygen sensor (HO2S) 1, bank 1 – exhaust sample | ||
P2414 | Exhaust leak, HO2S | |
error | ||
P2414 | Oxygen sensor (O2S) 1, bank 1 – exhaust sample error | Exhaust leak, O2S |
Heated oxygen sensor (HO2S) 1, bank 2 – exhaust sample | ||
P2415 | Exhaust leak, HO2S | |
error | ||
P2415 | Oxygen sensor (O2S) 1, bank 2 – exhaust sample error | Exhaust leak, O2S |
Heated oxygen sensor (HO2S) 2, bank 1/heated oxygen | ||
P2416 | Wiring | |
sensor (HO2S) 3, bank 1 – signals transposed | ||
Oxygen sensor (O2S) 2, bank 1/oxygen sensor (O2S) 3, bank | ||
P2416 | Wiring | |
1 – signals transposed | ||
Heated oxygen sensor (HO2S) 2, bank 2/heated oxygen | ||
P2417 | Wiring | |
sensor (HO2S) 3, bank 2 – signals transposed | ||
Oxygen sensor (O2S) 2, bank 2/oxygen sensor (O2S) 3, bank | ||
P2417 | Wiring | |
2 – signals transposed | ||
P2418 | Evaporative emission (EVAP) switching valve – open circuit | Wiring, EVAP switching valve |
P2419 | Evaporative emission (EVAP) switching valve – circuit low | Wiring short to earth, EVAP switching valve |
P2420 | Evaporative emission (EVAP) switching valve – circuit high | Wiring short to positive, EVAP switching valve |
P2421 | Evaporative emission (EVAP) vent valve – valve stuck open | EVAP vent valve |
P2422 | Evaporative emission (EVAP) vent valve – valve stuck closed | EVAP vent valve |
Hydrocarbon (HC) catalytic converter, bank 1 – efficiency below | ||
P2423 | HC catalytic converter | |
threshold | ||
Hydrocarbon (HC) catalytic converter, bank 2 – efficiency below | ||
P2424 | HC catalytic converter | |
threshold | ||
P2425 | Exhaust gas recirculation (EGR) cooling valve – open circuit | Wiring, EGR cooling valve |
P2426 | Exhaust gas recirculation (EGR) cooling valve – circuit low | Wiring short to earth, EGR cooling valve |
P2427 | Exhaust gas recirculation (EGR) cooling valve – circuit high | Wiring short to positive, EGR cooling valve |
P2428 | Exhaust gas temperature (EGT), bank 1 – temperature too high | – |
P2429 | Exhaust gas temperature (EGT), bank 2 – temperature too high | – |
P242A | Exhaust gas temperature sensor 3, bank 1 – circuit malfunction | Wiring, exhaust gas temperature sensor, ECM |
Exhaust gas temperature sensor 3, bank 1 – circuit | ||
P242B | Wiring, exhaust gas temperature sensor, ECM | |
range/performance | ||
P242C | Exhaust gas temperature sensor 3, bank 1 – circuit low | Wiring, exhaust gas temperature sensor, ECM |
P242D | Exhaust gas temperature sensor 3, bank 1 – circuit high | Wiring, exhaust gas temperature sensor, ECM |
Exhaust gas temperature sensor 3, bank 1 – circuit | ||
P242E | Wiring, exhaust gas temperature sensor, ECM | |
intermittent/erratic | ||
P242F | Diesel particulate filter (DPF) – blockage/ash accumulation | DPF |
Secondary air injection (AIR) system, air flow/pressure sensor, | ||
P2430 | Wiring, air flow/pressure sensor | |
bank 1 – circuit malfunction | ||
Secondary air injection (AIR) system, air flow/pressure sensor, | ||
P2431 | Wiring, air flow/pressure sensor | |
bank 1 – range/performance problem | ||
Secondary air injection (AIR) system, air flow/pressure sensor, | ||
P2432 | Wiring short to earth, air flow/pressure sensor | |
bank 1 – circuit low | ||
Secondary air injection (AIR) system, air flow/pressure sensor, | ||
P2433 | Wiring short to positive, air flow/pressure sensor | |
bank 1 – circuit high | ||
Secondary air injection (AIR) system, air flow/pressure sensor, | ||
P2434 | Wiring, poor connection, air flow/pressure sensor | |
bank 1 – circuit intermittent/erratic | ||
Secondary air injection (AIR) system, air flow/pressure sensor, | ||
P2435 | Wiring, air flow/pressure sensor | |
bank 2 – circuit malfunction | ||
Secondary air injection (AIR) system, air flow/pressure sensor, | ||
P2436 | Wiring, air flow/pressure sensor | |
bank 2 – range/performance problem | ||
Secondary air injection (AIR) system, air flow/pressure sensor, | ||
P2437 | Wiring short to earth, air flow/pressure sensor | |
bank 2 – circuit low | ||
Secondary air injection (AIR) system, air flow/pressure sensor, | ||
P2438 | Wiring short to positive, air flow/pressure sensor | |
bank 2 – circuit high | ||
Secondary air injection (AIR) system, air flow/pressure sensor, | ||
P2439 | Wiring, poor connection, air flow/pressure sensor | |
bank 2 – circuit intermittent/erratic | ||
Secondary air injection (AIR) switching valve, bank 1 – valve | ||
P2440 | AIR switching valve | |
stuck open | ||
Secondary air injection (AIR) switching valve, bank 1 – valve | ||
P2441 | AIR switching valve | |
stuck closed | ||
Secondary air injection (AIR) switching valve, bank 2 – valve | ||
P2442 | AIR switching valve | |
stuck open | ||
Secondary air injection (AIR) switching valve, bank 2 – valve | ||
P2443 | AIR switching valve | |
stuck closed | ||
P2444 | Secondary air injection (AIR) pump, bank 1 – pump stuck on | AIR pump |
P2445 | Secondary air injection (AIR) pump, bank 1 – pump stuck off | AIR pump |
P2446 | Secondary air injection (AIR) pump, bank 2 – pump stuck on | AIR pump |
P2447 | Secondary air injection (AIR) pump, bank 2 – pump stuck off | AIR pump |
P2448 | Secondary air injection (AIR), bank 1 – air flow high | Wiring, AIR switching valve, AIR pump |
P2449 | Secondary air injection (AIR), bank 2 – air flow high | Wiring, AIR switching valve, AIR pump |
P244A | Diesel particulate filter (DPF) – differential pressure too low | – |
P244B | Diesel particulate filter (DPF) – differential pressure too high | – |
Diesel particulate filter (DPF), bank 1 – exhaust temperature | ||
P244C | – | |
too low for regeneration | ||
Diesel particulate filter (DPF), bank 1 – exhaust temperature | ||
P244D | – | |
too high for regeneration | ||
Diesel particulate filter (DPF), bank 2 – exhaust temperature | ||
P244E | – | |
too low for regeneration | ||
Diesel particulate filter (DPF), bank 2 – exhaust temperature | ||
P244F | – | |
too high for regeneration | ||
Evaporative emission (EVAP) switching valve – performance | ||
P2450 | – | |
problem or valve stuck open | ||
Evaporative emission (EVAP) switching valve – valve stuck | ||
P2451 | – | |
closed | ||
Diesel particulate filter (DPF) pressure sensor A – circuit | ||
P2452 | Wiring, DPF pressure sensor, ECM | |
malfunction | ||
Diesel particulate filter (DPF) pressure sensor A – circuit | ||
P2453 | Wiring, DPF pressure sensor, ECM | |
malfunction | ||
P2454 | Diesel particulate filter (DPF) pressure sensor A – circuit low | Wiring, DPF pressure sensor, ECM |
P2455 | Diesel particulate filter (DPF) pressure sensor A – circuit high | Wiring, DPF pressure sensor, ECM |
Diesel particulate filter (DPF) pressure sensor A – circuit | ||
P2456 | Wiring, DPF pressure sensor, ECM | |
malfunction | ||
Exhaust gas recirculation (EGR) cooling system – performance | ||
P2457 | – | |
problem | ||
Diesel particulate filter (DPF), regeneration process – duration | ||
P2458 | – | |
malfunction | ||
Diesel particulate filter (DPF), regeneration process – number | ||
P2459 | – | |
of DPF regeneration cycles too high | ||
Exhaust gas recirculation (EGR) cooler bypass valve – control | ||
P245A | Wiring, EGR cooler bypass valve, ECM | |
circuit malfunction | ||
Exhaust gas recirculation (EGR) cooler bypass valve – control | ||
P245B | Wiring, EGR cooler bypass valve, ECM | |
circuit range/performance | ||
Exhaust gas recirculation (EGR) cooler bypass valve – control | ||
P245C | Wiring, EGR cooler bypass valve, ECM | |
circuit low | ||
Exhaust gas recirculation (EGR) cooler bypass valve – control | ||
P245D | Wiring, EGR cooler bypass valve, ECM | |
circuit high | ||
Diesel particulate filter (DPF) pressure sensor B – circuit | ||
P245E | Wiring, DPF pressure sensor, ECM | |
malfunction | ||
Diesel particulate filter (DPF) pressure differential sensor B – | ||
P245F | Wiring, DPF pressure differential sensor, ECM | |
circuit range/performance | ||
P2460 | Diesel particulate filter (DPF) pressure sensor B – circuit low | Wiring, DPF pressure sensor, ECM |
P2461 | Diesel particulate filter (DPF) pressure sensor B – circuit high | Wiring, DPF pressure sensor, ECM |
Diesel particulate filter (DPF) pressure sensor B – circuit | ||
P2462 | Wiring, DPF pressure sensor, ECM | |
malfunction | ||
P2463 | Diesel particulate filter (DPF) – DPF restricted | soot accumulation |
Diesel particulate filter (DPF), bank 2 – differential pressure too | ||
P2464 | – | |
low | ||
Diesel particulate filter (DPF), bank 2 – differential pressure too | ||
P2465 | – | |
high | ||
P2466 | Exhaust gas temperature sensor 3, bank 2 – circuit malfunction | Wiring, exhaust gas temperature sensor, ECM |
Exhaust gas temperature sensor 3, bank 2 – circuit | ||
P2467 | Wiring, exhaust gas temperature sensor, ECM | |
range/performance | ||
P2468 | Exhaust gas temperature sensor 3, bank 2 – circuit low | Wiring, exhaust gas temperature sensor, ECM |
P2469 | Exhaust gas temperature sensor 3, bank 2 – circuit high | Wiring, exhaust gas temperature sensor, ECM |
P246A | Exhaust gas temperature sensor 3, bank 2 – circuit intermittent | Wiring, exhaust gas temperature sensor, ECM |
P246B | Diesel particulate filter (DPF) – vehicle conditions incorrect | – |
Diesel particulate filter (DPF) – DPF restricted, limp-home | ||
P246C | Wiring, DPF pressure sensor, ECM | |
mode activated | ||
P246D | Diesel particulate filter (DPF) pressure sensor – A/B correlation | Wiring, DPF pressure sensor, ECM |
P246E | Exhaust gas temperature sensor 4, bank 1 – circuit malfunction | Wiring, exhaust gas temperature sensor, ECM |
Exhaust gas temperature sensor 4, bank 1 – circuit | ||
P246F | Wiring, exhaust gas temperature sensor, ECM | |
range/performance | ||
P2470 | Exhaust gas temperature sensor 4, bank 1 – circuit low | Wiring, exhaust gas temperature sensor, ECM |
P2471 | Exhaust gas temperature sensor 4, bank 1 – circuit high | Wiring, exhaust gas temperature sensor, ECM |
P2472 | Exhaust gas temperature sensor 4, bank 1 – circuit intermittent | Wiring, exhaust gas temperature sensor, ECM |
P2473 | Exhaust gas temperature sensor 4, bank 2 – circuit malfunction | Wiring, exhaust gas temperature sensor, ECM |
Exhaust gas temperature sensor 4, bank 2 – circuit | ||
P2474 | Wiring, exhaust gas temperature sensor, ECM | |
range/performance | ||
P2475 | Exhaust gas temperature sensor 4, bank 2 – circuit low | Wiring, exhaust gas temperature sensor, ECM |
P2476 | Exhaust gas temperature sensor 4, bank 2 – circuit high | Wiring, exhaust gas temperature sensor, ECM |
P2477 | Exhaust gas temperature sensor 4, bank 2 – circuit intermittent | Wiring, exhaust gas temperature sensor, ECM |
P2478 | Exhaust gas temperature sensor 1, bank 1 – out of range | Wiring, exhaust gas temperature sensor, ECM |
P2479 | Exhaust gas temperature sensor 2, bank 1 – out of range | Wiring, exhaust gas temperature sensor, ECM |
P247A | Exhaust gas temperature sensor 3, bank 1 – out of range | Wiring, exhaust gas temperature sensor, ECM |
P247B | Exhaust gas temperature sensor 4, bank 1 – out of range | Wiring, exhaust gas temperature sensor, ECM |
P247C | Exhaust gas temperature sensor 1, bank 2 – out of range | Wiring, exhaust gas temperature sensor, ECM |
P247D | Exhaust gas temperature sensor 2, bank 2 – out of range | Wiring, exhaust gas temperature sensor, ECM |
P247E | Exhaust gas temperature sensor 3, bank 2 – out of range | Wiring, exhaust gas temperature sensor, ECM |
P247F | Exhaust gas temperature sensor 4, bank 2 – out of range | Wiring, exhaust gas temperature sensor, ECM |
P2480 | Exhaust gas temperature sensor 5, bank 1 – open circuit | Wiring, exhaust gas temperature sensor, ECM |
P2481 | Exhaust gas temperature sensor 5, bank 1 – circuit low | Wiring, exhaust gas temperature sensor, ECM |
P2482 | Exhaust gas temperature sensor 5, bank 1 – circuit high | Wiring, exhaust gas temperature sensor, ECM |
Exhaust gas temperature sensor 5, bank 1 – circuit | ||
P2483 | Wiring, exhaust gas temperature sensor, ECM | |
range/performance | ||
P2484 | Exhaust gas temperature sensor 5, bank 1 – circuit intermittent | Wiring, exhaust gas temperature sensor, ECM |
P2485 | Exhaust gas temperature sensor 5, bank 2 – open circuit | Wiring, exhaust gas temperature sensor, ECM |
P2486 | Exhaust gas temperature sensor 5, bank 2 – circuit low | Wiring, exhaust gas temperature sensor, ECM |
P2487 | Exhaust gas temperature sensor 5, bank 2 – circuit high | Wiring, exhaust gas temperature sensor, ECM |
Exhaust gas temperature sensor 5, bank 2 – circuit | ||
P2488 | Wiring, exhaust gas temperature sensor, ECM | |
range/performance | ||
P2489 | Exhaust gas temperature sensor 5, bank 2 – circuit intermittent | Wiring, exhaust gas temperature sensor, ECM |
P248A | Reductant heater A, sense circuit – circuit low | Wiring, reductant heater, ECM |
P248B | Reductant heater A, sense circuit – circuit high | Wiring, reductant heater, ECM |
P248C | Reductant heater B, sense circuit – circuit low | Wiring, reductant heater, ECM |
P248D | Reductant heater B, sense circuit – circuit high | Wiring, reductant heater, ECM |
Exhaust gas recirculation (EGR) cooler bypass valve, bank 2 – | ||
P248E | Wiring, EGR cooler bypass valve, ECM | |
control circuit open | ||
Exhaust gas recirculation (EGR) cooler bypass valve, bank 2 – | ||
P248F | Wiring, EGR cooler bypass valve, ECM | |
control circuit range/performance | ||
Exhaust gas recirculation (EGR) cooler bypass valve, bank 2 – | ||
P2490 | Wiring, EGR cooler bypass valve, ECM | |
control circuit low | ||
Exhaust gas recirculation (EGR) cooler bypass valve, bank 2 – | ||
P2491 | Wiring, EGR cooler bypass valve, ECM | |
control circuit high | ||
Exhaust gas recirculation (EGR) cooler bypass flap position | ||
P2492 | Wiring, EGR cooler bypass flap position sensor, ECM | |
sensor, bank 1 – circuit malfunction | ||
Exhaust gas recirculation (EGR) cooler bypass flap position | ||
P2493 | Wiring, EGR cooler bypass flap position sensor, ECM | |
sensor, bank 1 – range/performance problem | ||
Exhaust gas recirculation (EGR) cooler bypass flap position | ||
P2494 | Wiring, EGR cooler bypass flap position sensor, ECM | |
sensor, bank 1 – circuit low | ||
Exhaust gas recirculation (EGR) cooler bypass flap position | ||
P2495 | Wiring, EGR cooler bypass flap position sensor, ECM | |
sensor, bank 1 – circuit high | ||
Exhaust gas recirculation (EGR) cooler bypass flap position | ||
P2496 | Wiring, EGR cooler bypass flap position sensor, ECM | |
sensor, bank 1 – circuit intermittent/erratic | ||
Exhaust gas recirculation (EGR) cooler bypass flap position | ||
P2497 | Wiring, EGR cooler bypass flap position sensor, ECM | |
sensor, bank 2 – circuit malfunction | ||
Exhaust gas recirculation (EGR) cooler bypass flap position | ||
P2498 | Wiring, EGR cooler bypass flap position sensor, ECM | |
sensor, bank 2 – range/performance problem | ||
Exhaust gas recirculation (EGR) cooler bypass flap position | ||
P2499 | Wiring, EGR cooler bypass flap position sensor, ECM | |
sensor, bank 2 – circuit low | ||
Exhaust gas recirculation (EGR) cooler bypass flap position | ||
P249A | Wiring, EGR cooler bypass flap position sensor, ECM | |
sensor, bank 2 – circuit high | ||
Exhaust gas recirculation (EGR) cooler bypass flap position | ||
P249B | Wiring, EGR cooler bypass flap position sensor, ECM | |
sensor, bank 2 – circuit intermittent/erratic | ||
P249C | Excessive time to enter closed loop reductant injection control | – |
Closed loop reductant injection control, control limit reached – | ||
P249D | – | |
low flow detected | ||
Closed loop reductant injection control, control limit reached – | ||
P249E | – | |
high flow detected | ||
Excessive time to enter closed loop Diesel particulate filter | ||
P249F | – | |
(DPF) regeneration control | ||
Closed loop Diesel particulate filter (DPF) regeneration control, | ||
P24A0 | – | |
control limit reached – temperature too low | ||
Closed loop Diesel particulate filter (DPF) regeneration control, | ||
P24A1 | – | |
control limit reached – temperature too high | ||
Diesel particulate filter (DPF) regeneration – regeneration not | ||
P24A2 | – | |
completed | ||
P2500 | Alternator warning lamp, L-terminal – circuit low | Wiring short to earth, alternator, instrument panel |
P2501 | Alternator warning lamp, L-terminal – circuit high | Wiring short to positive, alternator, instrument panel |
P2502 | Charging system voltage | Wiring, alternator, battery |
P2503 | Charging system – voltage low | Wiring, alternator, battery |
P2504 | Charging system – voltage high | Wiring, alternator, battery |
P2505 | Engine control module (ECM) – supply voltage | Wiring, fuses, engine control (EC) relay |
Engine control module (ECM) – supply voltage, | ||
P2506 | Wiring, fuses, engine control (EC) relay | |
range/performance problem | ||
P2507 | Engine control module (ECM) – supply voltage low | Wiring short to earth, fuses, engine control (EC) relay |
P2508 | Engine control module (ECM) – supply voltage high | Charging system |
P2509 | Engine control module (ECM) – supply voltage, intermittent | Wiring, fuses, engine control (EC) relay |
P250A | Engine oil level sensor – circuit malfunction | Wiring, engine oil level sensor, ECM |
P250B | Engine oil level sensor – circuit range/performance | Wiring, engine oil level sensor, ECM |
P250C | Engine oil level sensor – circuit low | Wiring, engine oil level sensor, ECM |
P250D | Engine oil level sensor – circuit high | Wiring, engine oil level sensor, ECM |
P250E | Engine oil level sensor – circuit intermittent/erratic | Wiring, engine oil level sensor, ECM |
P250F | Engine oil level too low | Wiring, engine oil level, ECM |
Engine control (EC) relay, sense circuit – range/performance | ||
P2510 | Wiring, fuses, EC relay | |
problem | ||
P2511 | Engine control (EC) relay, sense circuit – circuit intermittent | Wiring, poor connection, EC relay |
P2512 | Event data recorder request – open circuit | Wiring |
P2513 | Event data recorder request – circuit low | Wiring short to earth |
P2514 | Event data recorder request – circuit high | Wiring short to positive |
P2515 | AC refrigerant pressure sensor B – circuit malfunction | Wiring, AC refrigerant pressure sensor |
P2516 | AC refrigerant pressure sensor B – range/performance problem | Wiring, AC refrigerant pressure sensor |
P2517 | AC refrigerant pressure sensor B – circuit low | Wiring short to earth, AC refrigerant pressure sensor |
P2518 | AC refrigerant pressure sensor B – circuit high | Wiring short to positive, AC refrigerant pressure sensor |
Wiring, AC control module, AC master switch, AC | ||
P2519 | AC request A – circuit malfunction | |
refrigerant pressure switch/sensor | ||
P251A | Power take-off (PTO) enable switch – open circuit | Wiring, PTO enable switch, ECM |
P251B | Power take-off (PTO) enable switch – circuit low | Wiring, PTO enable switch, ECM |
P251C | Power take-off (PTO) enable switch – circuit high | Wiring, PTO enable switch, ECM |
P251D | Power take-off (PTO), engine shut-down – open circuit | Wiring, ECM |
P251E | Power take-off (PTO), engine shut-down – circuit low | Wiring, ECM |
Power take-off (PTO) monitoring, engine shut-off control – | ||
P251F | Wiring, ECM | |
circuit high | ||
Wiring short to earth, AC control module, AC master | ||
P2520 | AC request A – circuit low | |
switch, AC refrigerant pressure switch/sensor | ||
P2521 | AC request A – circuit high | Wiring short to positive, AC control module |
Wiring, AC control module, AC master switch, AC | ||
P2522 | AC request B – circuit malfunction | |
refrigerant pressure switch/sensor | ||
Wiring short to earth, AC control module, AC master | ||
P2523 | AC request B – circuit low | |
switch, AC refrigerant pressure switch/sensor | ||
P2524 | AC request B – circuit high | Wiring short to positive, AC control module |
P2525 | Vacuum reservoir pressure sensor – circuit malfunction | Wiring, vacuum reservoir pressure sensor |
Vacuum reservoir pressure sensor – range/performance | Wiring, vacuum reservoir pressure sensor, hoses | |
P2526 | ||
problem | blocked/leaking | |
Wiring short to earth, vacuum reservoir pressure | ||
P2527 | Vacuum reservoir pressure sensor – circuit low | |
sensor | ||
Wiring short to positive, vacuum reservoir pressure | ||
P2528 | Vacuum reservoir pressure sensor – circuit high | |
sensor | ||
Wiring, poor connection, vacuum reservoir pressure | ||
P2529 | Vacuum reservoir pressure sensor – circuit intermittent | |
sensor | ||
P252A | Engine oil quality sensor – circuit malfunction | Wiring, engine oil quality sensor, ECM |
P252B | Engine oil quality sensor – circuit range/performance | Wiring, engine oil quality sensor, ECM |
P252C | Engine oil quality sensor – circuit low | Wiring, engine oil quality sensor, ECM |
P252D | Engine oil quality sensor – circuit high | Wiring, engine oil quality sensor, ECM |
P252E | Engine oil quality sensor – circuit intermittent/erratic | Wiring, engine oil quality sensor, ECM |
P252F | Engine oil level too high | Engine oil level |
P2530 | Ignition switch, ON position – circuit malfunction | Wiring, fuse, ignition switch |
P2531 | Ignition switch, ON position – circuit low | Wiring short to earth, fuse, ignition switch |
P2532 | Ignition switch, ON position – circuit high | Wiring short to positive, fuse, ignition switch |
P2533 | Ignition switch, ON/start position – circuit malfunction | Wiring, fuse, ignition switch |
P2534 | Ignition switch, ON/start position – circuit low | Wiring short to earth, fuse, ignition switch |
P2535 | Ignition switch, ON/start position – circuit high | Wiring short to positive, fuse, ignition switch |
P2536 | Ignition switch, accessory position – circuit malfunction | Wiring, fuse, ignition switch |
P2537 | Ignition switch, accessory position – circuit low | Wiring short to earth, fuse, ignition switch |
P2538 | Ignition switch, accessory position – circuit high | Wiring short to positive, fuse, ignition switch |
P2539 | Fuel low pressure sensor – circuit malfunction | Wiring, fuel low pressure sensor |
P253A | Power take-off (PTO) monitoring – circuit open | Wiring, ECM |
P253B | Power take-off (PTO) monitoring – circuit range/performance | Wiring, ECM |
P253C | Power take-off (PTO) monitoring – circuit low | Wiring, ECM |
P253D | Power take-off (PTO) monitoring – circuit high | Wiring, ECM |
P253E | Power take-off (PTO) – sense circuit intermittent malfunction | – |
P253F | Engine oil deteriorated | Engine oil |
P2540 | Fuel low pressure sensor – range/performance problem | Wiring, fuel low pressure sensor |
P2541 | Fuel low pressure sensor – circuit low | Wiring short to earth, fuel low pressure sensor |
P2542 | Fuel low pressure sensor – circuit high | Wiring short to positive, fuel low pressure sensor |
P2543 | Fuel low pressure sensor – circuit intermittent | Wiring, poor connection, fuel low pressure sensor |
P2544 | Torque management request, input signal A – malfunction | Wiring, ECM, TCM |
Torque management request, input signal A – | ||
P2545 | Wiring, ECM, TCM | |
range/performance problem | ||
P2546 | Torque management request, input signal A – signal low | Wiring short to earth, ECM, TCM |
P2547 | Torque management request, input signal A – signal high | Wiring short to positive, ECM, TCM |
P2548 | Torque management request, input signal B – malfunction | Wiring, ECM, TCM |
Torque management request, input signal B – | ||
P2549 | Wiring, ECM, TCM | |
range/performance problem | ||
Power take-off (PTO) speed selector sensor/switch 1 – open | ||
P254A | Wiring, PTO speed selector sensor/switch, ECM | |
circuit | ||
Power take-off (PTO) speed selector sensor/switch 1 – circuit | ||
P254B | Wiring, PTO speed selector sensor/switch, ECM | |
range/performance | ||
Power take-off (PTO) speed selector sensor/switch 1 – circuit | ||
P254C | Wiring, PTO speed selector sensor/switch, ECM | |
low | ||
Power take-off (PTO) speed selector sensor/switch 1 – circuit | ||
P254D | Wiring, PTO speed selector sensor/switch, ECM | |
high | ||
Power take-off (PTO) speed selector sensor/switch 1 – circuit | ||
P254E | Wiring, PTO speed selector sensor/switch, ECM | |
intermittent/erratic | ||
P254F | Bonnet switch – open circuit | Wiring, bonnet switch, ECM |
P2550 | Torque management request, input signal B – signal low | Wiring short to earth, ECM, TCM |
P2551 | Torque management request, input signal B – signal high | Wiring short to positive, ECM, TCM |
P2552 | Throttle/fuel inhibit – circuit malfunction | Wiring |
P2553 | Throttle/fuel inhibit – range/performance problem | Wiring |
P2554 | Throttle/fuel inhibit – circuit low | Wiring short to earth |
P2555 | Throttle/fuel inhibit – circuit high | Wiring short to positive |
P2556 | Engine coolant ‘low’ sensor/switch – circuit malfunction | Wiring, engine coolant ‘low’ sensor/switch |
Engine coolant ‘low’ sensor/switch – range/performance | ||
P2557 | Wiring, engine coolant ‘low’ sensor/switch | |
problem | ||
P2558 | Engine coolant ‘low’ sensor/switch – circuit low | Wiring short to earth, engine coolant ‘low’ sensor/switch |
Wiring short to positive, engine coolant ‘low’ | ||
P2559 | Engine coolant ‘low’ sensor/switch – circuit high | |
sensor/switch | ||
Power take-off (PTO) speed selector sensor/switch 2 – open | ||
P255A | Wiring, PTO speed selector sensor/switch, ECM | |
circuit | ||
Power take-off (PTO) speed selector sensor/switch 2 – circuit | ||
P255B | Wiring, PTO speed selector sensor/switch, ECM | |
range/performance | ||
Power take-off (PTO) speed selector sensor/switch 2 – circuit | ||
P255C | Wiring, PTO speed selector sensor/switch, ECM | |
low | ||
Power take-off (PTO) speed selector sensor/switch 2 – circuit | ||
P255D | Wiring, PTO speed selector sensor/switch, ECM | |
high | ||
Power take-off (PTO) speed selector sensor/switch 2 – circuit | ||
P255E | Wiring, PTO speed selector sensor/switch, ECM | |
intermittent/erratic | ||
P255F | AC request A – circuit range/performance | Wiring, AC control module, ECM |
P2560 | Engine coolant level low | Engine coolant level low |
P2561 | AC control module – MIL activation requested | AC control module trouble codes stored |
Turbocharger (TC) boost control position sensor – circuit | ||
P2562 | Wiring, TC boost control position sensor | |
malfunction | ||
Turbocharger (TC) boost control position sensor – | ||
P2563 | Wiring, TC boost control position sensor | |
range/performance problem | ||
P2564 | Turbocharger (TC) boost control position sensor – circuit low | Wiring short to earth, TC boost control position sensor |
Wiring short to positive, TC boost control position | ||
P2565 | Turbocharger (TC) boost control position sensor – circuit high | |
sensor | ||
Turbocharger (TC) boost control position sensor – circuit | Wiring, poor connection, TC boost control position | |
P2566 | ||
intermittent | sensor | |
Direct ozone reduction catalytic converter temperature sensor – | Wiring, direct ozone reduction catalytic converter | |
P2567 | ||
circuit malfunction | temperature sensor | |
Direct ozone reduction catalytic converter temperature sensor – | Wiring, direct ozone reduction catalytic converter | |
P2568 | ||
range/performance problem | temperature sensor | |
Direct ozone reduction catalytic converter temperature sensor – | Wiring short to earth, direct ozone reduction catalytic | |
P2569 | ||
circuit low | converter temperature sensor | |
P256A | Engine idle speed selector sensor/switch – open circuit | Wiring, engine idle speed selector sensor/switch, ECM |
Engine idle speed selector sensor/switch – circuit | ||
P256B | Wiring, engine idle speed selector sensor/switch, ECM | |
range/performance | ||
P256C | Engine idle speed selector sensor/switch – circuit low | Wiring, engine idle speed selector sensor/switch, ECM |
P256D | Engine idle speed selector sensor/switch – circuit high | Wiring, engine idle speed selector sensor/switch, ECM |
Engine idle speed selector sensor/switch – circuit | ||
P256E | Wiring, engine idle speed selector sensor/switch, ECM | |
intermittent/erratic | ||
P256F | AC request B – circuit range/performance | Wiring, AC control module, ECM |
Direct ozone reduction catalytic converter temperature sensor – | Wiring short to positive, direct ozone reduction catalytic | |
P2570 | ||
circuit high | converter temperature sensor | |
Direct ozone reduction catalytic converter temperature sensor – | Wiring, poor connection, direct ozone reduction | |
P2571 | ||
circuit intermittent/erratic | catalytic converter temperature sensor | |
Wiring, direct ozone reduction catalytic converter | ||
P2572 | Direct ozone reduction catalytic converter deterioration sensor | |
deterioration sensor | ||
Direct ozone reduction catalytic converter deterioration sensor | Wiring, direct ozone reduction catalytic converter | |
P2573 | ||
– range/performance problem | deterioration sensor | |
Direct ozone reduction catalytic converter deterioration sensor | Wiring short to earth, direct ozone reduction catalytic | |
P2574 | ||
– circuit low | converter deterioration sensor | |
Direct ozone reduction catalytic converter deterioration sensor | Wiring short to positive, direct ozone reduction catalytic | |
P2575 | ||
– circuit high | converter deterioration sensor | |
Direct ozone reduction catalytic converter deterioration sensor | Wiring, poor connection, direct ozone reduction | |
P2576 | ||
– circuit intermittent/erratic | catalytic converter deterioration sensor | |
Direct ozone reduction catalytic converter – efficiency below | ||
P2577 | Direct ozone reduction catalytic converter | |
threshold | ||
P2578 | Turbocharger (TC) speed sensor – circuit malfunction | Wiring, TC speed sensor, ECM |
P2579 | Turbocharger (TC) speed sensor – circuit range/performance | Wiring, TC speed sensor, ECM |
P257A | Vacuum reservoir control – open circuit | – |
P257B | Vacuum reservoir control – circuit low | – |
P257C | Vacuum reservoir control – circuit high | – |
P257D | Bonnet switch – circuit range/performance | Wiring, bonnet switch, ECM |
P257E | Bonnet switch – circuit low | Wiring, bonnet switch, ECM |
P257F | Bonnet switch – circuit high | Wiring, bonnet switch, ECM |
P2580 | Turbocharger (TC) speed sensor – circuit low | Wiring, TC speed sensor, ECM |
P2581 | Turbocharger (TC) speed sensor – circuit high | Wiring, TC speed sensor, ECM |
P2582 | Turbocharger (TC) speed sensor – circuit intermittent | Wiring, TC speed sensor, ECM |
P2583 | Cruise control distance range sensor, front centre – malfunction | – |
P2584 | Fuel additive control module – MIL activation requested | – |
P2585 | Fuel additive control module – MIL activation requested | – |
Turbocharger (TC) boost control position sensor B – circuit | ||
P2586 | Wiring, TC boost control position sensor, ECM | |
malfunction | ||
Turbocharger (TC) boost control position sensor B – circuit | ||
P2587 | Wiring, TC boost control position sensor, ECM | |
malfunction | ||
P2588 | Turbocharger (TC) boost control position sensor B – circuit low | Wiring, TC boost control position sensor, ECM |
P2589 | Turbocharger (TC) boost control position sensor B – circuit high | Wiring, TC boost control position sensor, ECM |
P258A | Vacuum pump – control circuit open | Wiring, vacuum pump, ECM |
P258B | Vacuum pump control – range/performance problem | Wiring, vacuum pump, ECM |
P258C | Vacuum pump control – circuit low | Wiring, vacuum pump, ECM |
P258D | Vacuum pump – control circuit high | Wiring, vacuum pump, ECM |
P258E | Power take-off (PTO) enable switch – performance problem | Wiring, PTO enable switch, ECM |
P258F | Torque management request – output signal malfunction | Wiring, TCM, ECM |
Turbocharger (TC) boost control position sensor B – circuit | ||
P2590 | Wiring, TC boost control position sensor, ECM | |
malfunction | ||
P2591 | Cruise control distance range sensor, front left – malfunction | – |
P2592 | Cruise control distance range sensor, front right – malfunction | – |
P2593 | Turbocharger (TC) speed sensor B – circuit malfunction | Wiring, TC speed sensor, ECM |
P2594 | Turbocharger (TC) speed sensor B – circuit range/performance | Wiring, TC speed sensor, ECM |
P2595 | Turbocharger (TC) speed sensor B – circuit low | Wiring, TC speed sensor, ECM |
P2596 | Turbocharger (TC) speed sensor B – circuit high | Wiring, TC speed sensor, ECM |
P2597 | Turbocharger (TC) speed sensor B – circuit intermittent/erratic | Wiring, TC speed sensor, ECM |
Turbocharger (TC) boost control position sensor A, | ||
P2598 | Wiring, TC boost control position sensor, ECM | |
performance problem – signal low | ||
Turbocharger (TC) boost control position sensor A, | ||
P2599 | Wiring, TC boost control position sensor, ECM | |
performance problem – signal high | ||
Turbocharger (TC) boost control position sensor B, | ||
P259A | Wiring, TC boost control position sensor, ECM | |
performance problem – signal low | ||
Turbocharger (TC) boost control position sensor B, | ||
P259B | Wiring, TC boost control position sensor, ECM | |
performance problem – signal high | ||
Excessive time to enter closed loop turbocharger A boost | ||
P259C | – | |
control | ||
Excessive time to enter closed loop turbocharger B boost | ||
P259D | – | |
control | ||
Turbocharger (TC) A, boost pressure control – lower limit | ||
P259E | – | |
reached | ||
Turbocharger (TC) A, boost pressure control – higher limit | ||
P259F | – | |
reached | ||
Turbocharger (TC) B, boost pressure control – lower limit | ||
P25A0 | – | |
reached | ||
Turbocharger (TC) B, boost pressure control – higher limit | ||
P25A1 | – | |
reached | ||
P2600 | Engine coolant pump motor – open circuit | Wiring, engine coolant pump relay |
P2601 | Engine coolant pump motor – range/performance problem | Wiring, engine coolant pump relay |
P2602 | Engine coolant pump motor – circuit low | Wiring short to earth, engine coolant pump relay |
P2603 | Engine coolant pump motor – circuit high | Wiring short to positive, engine coolant pump relay |
P2604 | Intake air heater A – range/performance problem | Wiring, intake air heater relay, intake air heater |
P2605 | Intake air heater A – open circuit | Wiring, intake air heater relay, intake air heater |
P2606 | Intake air heater B – range/performance problem | Wiring, intake air heater relay, intake air heater |
Wiring short to earth, intake air heater relay, intake air | ||
P2607 | Intake air heater B – circuit low | |
heater | ||
Wiring short to positive, intake air heater relay, intake | ||
P2608 | Intake air heater B – circuit high | |
air heater | ||
P2609 | Intake air heater system – performance problem | Wiring, intake air heater relay, intake air heater |
P260A | Power take-off (PTO), control – open circuit | Wiring |
P260B | Power take-off (PTO), control – circuit low | Wiring, ECM |
P260C | Power take-off (PTO) control – circuit high | – |
P260D | Power take-off (PTO) engaged warning lamp – control circuit | Wiring, warning lamp, ECM |
Diesel particulate filter (DPF) warning lamp – control circuit | ||
P260E | Wiring, DPF warning lamp | |
malfunction | ||
Evaporative emission (EVAP) system – monitoring processor | ||
P260F | ECM | |
performance problem | ||
Engine control module (ECM) – internal engine off timer | ||
P2610 | ECM | |
performance | ||
P2611 | AC refrigerant distribution valve – open circuit | Wiring, AC refrigerant distribution valve |
P2612 | AC refrigerant distribution valve – circuit low | Wiring short to earth, AC refrigerant distribution valve |
P2613 | AC refrigerant distribution valve – circuit high | Wiring short to positive, AC refrigerant distribution valve |
P2614 | Camshaft position (CMP), output signal – open circuit | Wiring, ECM |
P2615 | Camshaft position (CMP), output signal – circuit low | Wiring short to earth, ECM |
P2616 | Camshaft position (CMP), output signal – circuit high | Wiring short to positive, ECM |
P2617 | Crankshaft position (CKP), output signal – open circuit | Wiring, ECM |
P2618 | Crankshaft position (CKP), output signal – circuit low | Wiring short to earth, ECM |
P2619 | Crankshaft position (CKP), output signal – circuit high | Wiring short to positive, ECM |
P261A | Engine coolant pump motor B – control circuit open | Wiring, engine coolant pump motor, ECM |
Engine coolant pump motor B – control circuit | ||
P261B | Wiring, engine coolant pump motor, ECM | |
range/performance | ||
P261C | Engine coolant pump motor B – control circuit low | Wiring, engine coolant pump motor, ECM |
P261D | Engine coolant pump motor B – control circuit high | Wiring, engine coolant pump motor, ECM |
P2620 | Throttle position (TP), output signal – open circuit | Wiring, ECM |
P2621 | Throttle position (TP), output signal – circuit low | Wiring short to earth, ECM |
P2622 | Throttle position (TP), output signal – circuit high | Wiring short to positive, ECM |
P2623 | Injector control pressure regulator – open circuit | Wiring, injector control pressure regulator |
P2624 | Injector control pressure regulator – circuit low | Wiring short to earth, injector control pressure regulator |
Wiring short to positive, injector control pressure | ||
P2625 | Injector control pressure regulator – circuit high | |
regulator | ||
Heated oxygen sensor (HO2S) 1, bank 1, pumping current trim | ||
P2626 | Wiring, HO2S, ECM | |
– open circuit | ||
Oxygen sensor (O2S) 1, bank 1, pumping current trim – open | ||
P2626 | Wiring, O2S, ECM | |
circuit | ||
Heated oxygen sensor (HO2S) 1, bank 1, pumping current trim | ||
P2627 | Wiring short to earth, HO2S, ECM | |
– circuit low | ||
Oxygen sensor (O2S) 1, bank 1, pumping current trim – circuit | ||
P2627 | Wiring short to earth, O2S, ECM | |
low | ||
Heated oxygen sensor (HO2S) 1, bank 1, pumping current trim | ||
P2628 | Wiring short to positive, HO2S, ECM | |
– circuit high | ||
Oxygen sensor (O2S) 1, bank 1, pumping current trim – circuit | ||
P2628 | Wiring short to positive, O2S, ECM | |
high | ||
Heated oxygen sensor (HO2S) 1, bank 2, pumping current trim | ||
P2629 | Wiring, HO2S, ECM | |
– open circuit | ||
Oxygen sensor (O2S) 1, bank 2, pumping current trim – open | ||
P2629 | Wiring, O2S, ECM | |
circuit | ||
Heated oxygen sensor (HO2S) 1, bank 2, pumping current trim | ||
P2630 | Wiring short to earth, HO2S, ECM | |
– circuit low | ||
Oxygen sensor (O2S) 1, bank 2, pumping current trim – circuit | ||
P2630 | Wiring short to earth, O2S, ECM | |
low | ||
Heated oxygen sensor (HO2S) 1, bank 2, pumping current trim | ||
P2631 | Wiring short to positive, HO2S, ECM | |
– circuit high | ||
Oxygen sensor (O2S) 1, bank 2, pumping current trim – circuit | ||
P2631 | Wiring short to positive, O2S, ECM | |
high | ||
P2632 | Fuel pump (FP) B, control – open circuit | Wiring, FP relay, ECM |
P2633 | Fuel pump (FP) B, control – circuit low | Wiring short to earth, FP relay, ECM |
P2634 | Fuel pump (FP) B, control – circuit high | Wiring short to positive, FP relay, ECM |
P2635 | Fuel pump (FP) A – low flow/performance problem | Fuel filter blocked, fuel pump (FP) |
P2636 | Fuel pump (FP) B – low flow/performance problem | Fuel filter blocked, fuel pump (FP) |
P2637 | Torque management, feedback signal A – malfunction | Wiring, ECM, TCM |
Torque management, feedback signal A – range/performance | ||
P2638 | Wiring, ECM, TCM | |
problem | ||
P2639 | Torque management, feedback signal A – signal low | |
P2640 | Torque management, feedback signal A – signal high | |
P2641 | Torque management, feedback signal B – malfunction | Wiring, ECM, TCM |
Torque management, feedback signal B – range/performance | ||
P2642 | Wiring, ECM, TCM | |
problem | ||
P2643 | Torque management, feedback signal B – signal low | |
P2644 | Torque management, feedback signal B – signal high | |
P2645 | Rocker arm actuator A, bank 1 – open circuit | |
Rocker arm actuator A, bank 1 – performance problem or | ||
P2646 | ||
actuator stuck off | ||
P2647 | Rocker arm actuator A, bank 1 – actuator stuck on | Rocker arm actuator |
P2648 | Rocker arm actuator A, bank 1 – circuit low | |
P2649 | Rocker arm actuator A, bank 1 – circuit high | |
Rocker arm actuator position sensor A, bank 1 – circuit | ||
P264A | ||
malfunction | ||
Rocker arm actuator position sensor A, bank 1 – circuit | ||
P264B | ||
range/performance | ||
P264C | Rocker arm actuator position sensor A, bank 1 – circuit low | |
P264D | Rocker arm actuator position sensor A, bank 1 – circuit high | |
Rocker arm actuator position sensor A, bank 1 – circuit | ||
P264E | ||
intermittent/erratic | ||
P2650 | Rocker arm actuator B, bank 1 – open circuit | |
Rocker arm actuator B, bank 1 – performance problem or | ||
P2651 | Rocker arm actuator | |
actuator stuck off | ||
P2652 | Rocker arm actuator B, bank 1 – actuator stuck on | Rocker arm actuator |
P2653 | Rocker arm actuator B, bank 1 – circuit low | |
P2654 | Rocker arm actuator B, bank 1 – circuit high | |
P2655 | Rocker arm actuator A, bank 2 – open circuit | |
Rocker arm actuator A, bank 2 – performance problem or | ||
P2656 | Rocker arm actuator | |
actuator stuck off | ||
P2657 | Rocker arm actuator A, bank 2 – actuator stuck on | Rocker arm actuator |
P2658 | Rocker arm actuator A, bank 2 – circuit low | |
P2659 | Rocker arm actuator A, bank 2 – circuit high | |
Rocker arm actuator position sensor B, bank 1 – circuit | ||
P265A | ||
malfunction | ||
Rocker arm actuator position sensor B, bank 1 – circuit | ||
P265B | ||
range/performance | ||
P265C | Rocker arm actuator position sensor B, bank 1 – circuit low | |
P265D | Rocker arm actuator position sensor B, bank 1 – circuit high | |
Rocker arm actuator position sensor B, bank 1 – circuit | ||
P265E | ||
intermittent/erratic | ||
P2660 | Rocker arm actuator B, bank 2 – open circuit | |
Rocker arm actuator B, bank 2 – performance problem or | ||
P2661 | Rocker arm actuator | |
actuator stuck off | ||
P2662 | Rocker arm actuator B, bank 2 – actuator stuck on | Rocker arm actuator |
P2663 | Rocker arm actuator B, bank 2 – circuit low | Wiring short to earth, rocker arm actuator |
P2664 | Rocker arm actuator B, bank 2 – circuit high | Wiring short to positive, rocker arm actuator |
P2665 | Fuel shut-off solenoid B – open circuit | Wiring, fuel shut-off solenoid |
P2666 | Fuel shut-off solenoid B – circuit low | Wiring short to earth, fuel shut-off solenoid |
P2667 | Fuel shut-off solenoid B – circuit high | Wiring short to positive, fuel shut-off solenoid |
P2668 | Fuel mode indicator lamp – circuit malfunction | Wiring, fuel mode indicator lamp |
P2669 | Actuator supply voltage B – open circuit | Wiring, ECM |
Rocker arm actuator position sensor A, bank 2 – circuit | ||
P266A | Wiring, rocker arm actuator position sensor, ECM | |
malfunction | ||
Rocker arm actuator position sensor A, bank 2 – circuit | ||
P266B | Wiring, rocker arm actuator position sensor, ECM | |
range/performance | ||
P266C | Rocker arm actuator position sensor A, bank 2 – circuit low | Wiring, rocker arm actuator position sensor, ECM |
P266D | Rocker arm actuator position sensor A, bank 2 – circuit high | Wiring, rocker arm actuator position sensor, ECM |
Rocker arm actuator position sensor A, bank 2 – circuit | ||
P266E | Wiring, rocker arm actuator position sensor, ECM | |
intermittent/erratic | ||
P2670 | Actuator supply voltage B – circuit low | Wiring short to earth, ECM |
P2671 | Actuator supply voltage B – circuit high | Wiring short to positive, ECM |
P2672 | Injection pump timing offset – Offset malfunction | – |
P2673 | Injection pump timing calibration – calibration not learned | – |
P2674 | Injection pump fuel calibration – calibration not learned | – |
P2675 | Air filter inlet control – open circuit | |
P2676 | Air filter inlet control – circuit low | |
P2677 | Air filter inlet control – circuit high | |
P2678 | Engine coolant expansion tank valve control – open circuit | |
P2679 | Engine coolant expansion tank valve control – circuit low | |
Rocker arm actuator position sensor B, bank 2 – circuit | ||
P267A | Wiring, rocker arm actuator position sensor, ECM | |
malfunction | ||
Rocker arm actuator position sensor B, bank 2 – circuit | ||
P267B | Wiring, rocker arm actuator position sensor, ECM | |
range/performance | ||
P267C | Rocker arm actuator position sensor B, bank 2 – circuit low | Wiring, rocker arm actuator position sensor, ECM |
P267D | Rocker arm actuator position sensor B, bank 2 – circuit high | Wiring, rocker arm actuator position sensor, ECM |
Rocker arm actuator position sensor B, bank 2 – circuit | ||
P267E | Wiring, rocker arm actuator position sensor, ECM | |
intermittent/erratic | ||
P2680 | Engine coolant expansion tank valve control – circuit high | |
P2681 | Engine coolant bypass valve control – open circuit | |
P2682 | Engine coolant bypass valve control – circuit low | |
P2683 | Engine coolant bypass valve control – circuit high | |
P2684 | Actuator supply voltage C – open circuit | |
P2685 | Actuator supply voltage C – circuit low | |
P2686 | Actuator supply voltage C – circuit high | |
P2687 | Fuel heater – open circuit | Wiring, fuel heater, ECM |
P2688 | Fuel heater – circuit low | Wiring, fuel heater, ECM |
P2689 | Fuel heater – circuit high | Wiring, fuel heater, ECM |
P268A | Injector – calibration not learned/programmed | Calibration not learned |
P268B | Fuel high pressure pump – calibration not learned/programmed | Calibration not learned |
P268C | Injector 1 – data incompatible | Wiring, injector, ECM |
P268D | Injector 2 – data incompatible | Wiring, injector, ECM |
P268E | Injector 3 – data incompatible | Wiring, injector, ECM |
P268F | Injector 4 – data incompatible | Wiring, injector, ECM |
P2690 | Injector 5 – data incompatible | Wiring, injector, ECM |
P2691 | Injector 6 – data incompatible | Wiring, injector, ECM |
P2692 | Injector 7 – data incompatible | Wiring, injector, ECM |
P2693 | Injector 8 – data incompatible | Wiring, injector, ECM |
P2694 | Injector 9 – data incompatible | Wiring, injector, ECM |
P2695 | Injector 10 – data incompatible | Wiring, injector, ECM |
P2696 | Injector – data incompatible | Wiring, injector, ECM |
P2697 | Exhaust after treatment fuel injector A – open circuit | Wiring, exhaust after treatment fuel injector, ECM |
P2698 | Exhaust after treatment fuel injector A – performance problem | Wiring, exhaust after treatment fuel injector, ECM |
P2699 | Exhaust after treatment fuel injector A – circuit low | Wiring, exhaust after treatment fuel injector, ECM |
P269A | Exhaust after treatment fuel injector A – circuit high | Wiring, exhaust after treatment fuel injector, ECM |
P269B | Exhaust after treatment glow plug control – open circuit | Wiring, glow plug control, ECM |
Exhaust after treatment glow plug control – performance | ||
P269C | Wiring, glow plug control, ECM | |
problem | ||
P269D | Exhaust after treatment glow plug control – circuit low | Wiring, glow plug control, ECM |
P269E | Exhaust after treatment glow plug control – circuit high | Wiring, glow plug control, ECM |
P269F | Exhaust after treatment glow plug – open circuit | Wiring, glow plug, ECM |
P26A0 | Exhaust after treatment glow plug – performance problem | Wiring, glow plug, ECM |
P26A1 | Exhaust after treatment glow plug – circuit low | Wiring, glow plug, ECM |
P26A2 | Exhaust after treatment glow plug – circuit high | Wiring, glow plug, ECM |
Transmission friction element A, apply time – | ||
P2700 | Transmission mechanical fault, shift solenoid (SS) | |
range/performance problem | ||
Transmission friction element B, apply time – | ||
P2701 | Transmission mechanical fault, shift solenoid (SS) | |
range/performance problem | ||
Transmission friction element C, apply time – | ||
P2702 | Transmission mechanical fault, shift solenoid (SS) | |
range/performance problem | ||
Transmission friction element D, apply time – | ||
P2703 | Transmission mechanical fault, shift solenoid (SS) | |
range/performance problem | ||
Transmission friction element E, apply time – | ||
P2704 | Transmission mechanical fault, shift solenoid (SS) | |
range/performance problem | ||
Transmission friction element F, apply time – | ||
P2705 | Transmission mechanical fault, shift solenoid (SS) | |
range/performance problem | ||
P2706 | Shift solenoid (SS) F – circuit malfunction | Transmission mechanical fault, shift solenoid (SS) |
Shift solenoid (SS) F – performance problem or solenoid stuck | ||
P2707 | Transmission mechanical fault, shift solenoid (SS) | |
off | ||
P2708 | Shift solenoid (SS) F – solenoid stuck on | Transmission mechanical fault, shift solenoid (SS) |
P2709 | Shift solenoid (SS) F – electrical | Wiring, shift solenoid (SS) |
P2710 | Shift solenoid (SS) F – intermittent | Wiring, poor connection, shift solenoid (SS) |
P2711 | Unexpected mechanical gear disengagement | Operator error, transmission mechanical fault |
P2712 | Hydraulic power unit leakage | – |
Transmission fluid pressure (TFP) solenoid D – circuit | ||
P2713 | Wiring, TFP solenoid, TCM | |
malfunction | ||
Transmission fluid pressure (TFP) solenoid D – performance | ||
P2714 | Wiring, TFP solenoid, transmission mechanical fault | |
problem or solenoid stuck off | ||
Transmission fluid pressure (TFP) solenoid D – solenoid stuck | ||
P2715 | TFP solenoid, transmission mechanical fault | |
on | ||
P2716 | Transmission fluid pressure (TFP) solenoid D – electrical | Wiring, TFP solenoid |
Transmission fluid pressure (TFP) solenoid D – circuit | ||
P2717 | Wiring, poor connection, TFP solenoid, TCM | |
intermittent | ||
P2718 | Transmission fluid pressure (TFP) solenoid D – open circuit | Wiring, TFP solenoid, TCM |
Transmission fluid pressure (TFP) solenoid D – | ||
P2719 | TFP solenoid, transmission mechanical fault | |
range/performance problem | ||
P2720 | Transmission fluid pressure (TFP) solenoid D – circuit low | Wiring short to earth, TFP solenoid, TCM |
P2721 | Transmission fluid pressure (TFP) solenoid D – circuit high | Wiring short to positive, TFP solenoid, TCM |
Transmission fluid pressure (TFP) solenoid E – circuit | ||
P2722 | Wiring, TFP solenoid, TCM | |
malfunction | ||
Transmission fluid pressure (TFP) solenoid E – performance | ||
P2723 | Wiring, TFP solenoid, transmission mechanical fault | |
problem or solenoid stuck off | ||
Transmission fluid pressure (TFP) solenoid E – solenoid stuck | ||
P2724 | TFP solenoid, transmission mechanical fault | |
on | ||
P2725 | Transmission fluid pressure (TFP) solenoid E – electrical | Wiring, TFP solenoid |
Transmission fluid pressure (TFP) solenoid E – circuit | ||
P2726 | Wiring, poor connection, TFP solenoid, TCM | |
intermittent | ||
P2727 | Transmission fluid pressure (TFP) solenoid E – open circuit | Wiring, TFP solenoid, TCM |
Transmission fluid pressure (TFP) solenoid E – | ||
P2728 | TFP solenoid, transmission mechanical fault | |
range/performance problem | ||
P2729 | Transmission fluid pressure (TFP) solenoid E – circuit low | Wiring short to earth, TFP solenoid, TCM |
P2730 | Transmission fluid pressure (TFP) solenoid E – circuit high | Wiring short to positive, TFP solenoid, TCM |
Transmission fluid pressure (TFP) solenoid F – circuit | ||
P2731 | Wiring, TFP solenoid, TCM | |
malfunction | ||
Transmission fluid pressure (TFP) solenoid F – performance | ||
P2732 | Wiring, TFP solenoid, transmission mechanical fault | |
problem or solenoid stuck off | ||
Transmission fluid pressure (TFP) solenoid F – solenoid stuck | ||
P2733 | TFP solenoid, transmission mechanical fault | |
on | ||
P2734 | Transmission fluid pressure (TFP) solenoid F – electrical | Wiring, TFP solenoid |
Transmission fluid pressure (TFP) solenoid F – circuit | ||
P2735 | Wiring, poor connection, TFP solenoid, TCM | |
intermittent | ||
P2736 | Transmission fluid pressure (TFP) solenoid F – open circuit | Wiring, TFP solenoid, TCM |
Transmission fluid pressure (TFP) solenoid F – | ||
P2737 | TFP solenoid, transmission mechanical fault | |
range/performance problem | ||
P2738 | Transmission fluid pressure (TFP) solenoid F – circuit low | Wiring short to earth, TFP solenoid, TCM |
P2739 | Transmission fluid pressure (TFP) solenoid F – circuit high | Wiring short to positive, TFP solenoid, TCM |
Transmission friction element G, apply time – | Shift solenoid (SS), transmission mechanical fault, | |
P273A | ||
range/performance problem | TCM, ECM | |
Transmission friction element H, apply time – | Shift solenoid (SS), transmission mechanical fault, | |
P273B | ||
range/performance problem | TCM, ECM | |
Transmission fluid temperature (TFT) sensor B – circuit | ||
P2740 | Wiring, TFT sensor | |
malfunction | ||
Transmission fluid temperature (TFT) sensor B – circuit | ||
P2741 | Wiring, TFT sensor | |
range/performance | ||
P2742 | Transmission fluid temperature (TFT) sensor B – circuit low | Wiring short to earth, TFT sensor |
P2743 | Transmission fluid temperature (TFT) sensor B – circuit high | Wiring short to positive, TFT sensor |
Transmission fluid temperature (TFT) sensor B – circuit | ||
P2744 | Wiring, poor connection, TFT sensor | |
intermittent | ||
Transmission intermediate shaft speed sensor B – circuit | Wiring, transmission intermediate shaft speed sensor, | |
P2745 | ||
malfunction | ECM, TCM | |
Transmission intermediate shaft speed sensor B – | Wiring, transmission intermediate shaft speed sensor, | |
P2746 | ||
range/performance problem | ECM, TCM | |
Wiring, transmission intermediate shaft speed sensor, | ||
P2747 | Transmission intermediate shaft speed sensor B – no signal | |
ECM, TCM | ||
Transmission intermediate shaft speed sensor B – circuit | Wiring, poor connection, transmission intermediate | |
P2748 | ||
intermittent | shaft speed sensor, ECM, TCM | |
Transmission intermediate shaft speed sensor C – circuit | Wiring, transmission intermediate shaft speed sensor, | |
P2749 | ||
malfunction | ECM, TCM | |
Transmission intermediate shaft speed sensor C – | Wiring, transmission intermediate shaft speed sensor, | |
P2750 | ||
range/performance problem | ECM, TCM | |
Wiring, transmission intermediate shaft speed sensor, | ||
P2751 | Transmission intermediate shaft speed sensor C – no signal | |
ECM, TCM | ||
Transmission intermediate shaft speed sensor C – circuit | Wiring, poor connection, transmission intermediate | |
P2752 | ||
intermittent | shaft speed sensor, ECM, TCM | |
P2753 | Transmission fluid cooler – open circuit | Wiring, transmission fluid cooler |
P2754 | Transmission fluid cooler – circuit low | Wiring short to earth, transmission fluid cooler |
P2755 | Transmission fluid cooler – circuit high | Wiring short to positive, transmission fluid cooler |
Torque converter clutch (TCC) pressure control solenoid – | ||
P2756 | Wiring, TCC pressure control solenoid | |
circuit malfunction | ||
Torque converter clutch (TCC) pressure control solenoid – | ||
P2757 | TCC pressure control solenoid | |
performance problem or solenoid stuck off | ||
Torque converter clutch (TCC) pressure control solenoid – | ||
P2758 | TCC pressure control solenoid | |
solenoid stuck on | ||
Torque converter clutch (TCC) pressure control solenoid – | ||
P2759 | Wiring, TCC pressure control solenoid | |
electrical fault | ||
Torque converter clutch (TCC) pressure control solenoid – | ||
P2760 | Wiring, poor connection, TCC pressure control solenoid | |
circuit intermittent | ||
Torque converter clutch (TCC) pressure control solenoid – | ||
P2761 | Wiring, TCC pressure control solenoid | |
open circuit | ||
Torque converter clutch (TCC) pressure control solenoid – | ||
P2762 | Wiring, TCC pressure control solenoid | |
range/performance problem | ||
Torque converter clutch (TCC) pressure control solenoid – | ||
P2763 | Wiring short to positive, TCC pressure control solenoid | |
circuit high | ||
Torque converter clutch (TCC) pressure control solenoid – | ||
P2764 | Wiring short to earth, TCC pressure control solenoid | |
circuit low | ||
Transmission input shaft speed sensor/turbine shaft speed | Wiring, transmission input shaft speed sensor/TSS | |
P2765 | ||
(TSS) sensor B – circuit malfunction | sensor | |
Transmission input shaft speed sensor/turbine shaft speed | Wiring, transmission input shaft speed sensor/TSS | |
P2766 | ||
(TSS) sensor B – range/performance problem | sensor | |
Transmission input shaft speed sensor/turbine shaft speed | Wiring, transmission input shaft speed sensor/TSS | |
P2767 | ||
(TSS) sensor B – no signal | sensor | |
Transmission input shaft speed sensor/turbine shaft speed | Wiring, poor connection, transmission input shaft speed | |
P2768 | ||
(TSS) sensor B – circuit intermittent | sensor/TSS sensor | |
P2769 | Torque converter clutch (TCC) – circuit low | Wiring short to earth, TCC |
P2770 | Torque converter clutch (TCC) – circuit high | Wiring short to positive, TCC |
P2771 | Four wheel drive, low gear ratio switch – circuit malfunction | Wiring, low gear ratio switch |
Four wheel drive, low gear ratio switch – range/performance | ||
P2772 | Wiring, low gear ratio switch | |
problem | ||
P2773 | Four wheel drive, low gear ratio switch – circuit low | Wiring short to earth, low gear ratio switch |
P2774 | Four wheel drive, low gear ratio switch – circuit high | Wiring short to positive, low gear ratio switch |
Transmission gear selection switch, upshift – | ||
P2775 | Wiring, transmission gear selection switch | |
range/performance problem | ||
Wiring short to earth, transmission gear selection | ||
P2776 | Transmission gear selection switch, upshift – circuit low | |
switch | ||
Wiring short to positive, transmission gear selection | ||
P2777 | Transmission gear selection switch, upshift – circuit high | |
switch | ||
Transmission gear selection switch, upshift – circuit | Wiring, poor connection, transmission gear selection | |
P2778 | ||
intermittent/erratic | switch | |
Transmission gear selection switch, downshift – | ||
P2779 | Wiring, transmission gear selection switch | |
range/performance problem | ||
Wiring short to earth, transmission gear selection | ||
P2780 | Transmission gear selection switch, downshift – circuit low | |
switch | ||
Wiring short to positive, transmission gear selection | ||
P2781 | Transmission gear selection switch, downshift – circuit high | |
switch | ||
Transmission gear selection switch, downshift – circuit | Wiring, poor connection, transmission gear selection | |
P2782 | ||
intermittent/erratic | switch | |
Transmission fluid level low, transmission mechanical | ||
P2783 | Torque converter – temperature too high | |
fault, TCC slipping | ||
Transmission input shaft speed sensor/turbine shaft speed | Wiring, transmission input shaft speed sensor/TSS | |
P2784 | ||
(TSS) sensor A/B – correlation | sensor | |
P2785 | Clutch actuator – temperature too high | – |
P2786 | Gear shift actuator – temperature too high | – |
P2787 | Clutch – temperature too high | Clutch slipping |
Auto shift manual (ASM) transmission, adaptive learning – at | ||
P2788 | – | |
limit | ||
P2789 | Clutch, adaptive learning – at limit | – |
P278A | Transmission kick-down switch – circuit malfunction | Wiring, transmission kick-down switch, TCM, ECM |
P278B | Transmission kick-down switch – circuit range/performance | Wiring, transmission kick-down switch, TCM, ECM |
P278C | Transmission kick-down switch – circuit low | Wiring, transmission kick-down switch, TCM, ECM |
P278D | Transmission kick-down switch – circuit high | Wiring, transmission kick-down switch, TCM, ECM |
P278E | Transmission kick-down switch – circuit intermittent/erratic | Wiring, transmission kick-down switch, TCM, ECM |
P278F | Clutch B – adaptive learning at limit | – |
P2790 | Gate select direction – circuit malfunction | Wiring |
P2791 | Gate select direction – circuit low | Wiring short to earth |
P2792 | Gate select direction – circuit high | Wiring short to positive |
P2793 | Gear shift direction – circuit malfunction | Wiring |
P2794 | Gear shift direction – circuit low | Wiring short to earth |
P2795 | Gear shift direction – circuit high | Wiring short to positive |
Wiring, auxiliary transmission fluid pump control, TCM, | ||
P2796 | Auxiliary transmission fluid pump control – open circuit | |
ECM | ||
P2797 | Auxiliary transmission fluid pump – performance problem | Wiring, auxiliary transmission fluid pump |
Wiring, auxiliary transmission fluid pump control, TCM, | ||
P2798 | Auxiliary transmission fluid pump control – circuit low | |
ECM | ||
Wiring, auxiliary transmission fluid pump control, TCM, | ||
P2799 | Auxiliary transmission fluid pump control – circuit high | |
ECM | ||
P279A | Transfer box high gear – incorrect ratio | – |
P279B | Transfer box low gear – incorrect ratio | – |
P279C | Transfer box neutral gear – incorrect ratio | – |
P279D | Four wheel drive control – signal malfunction | – |
P279E | Four wheel drive control – control circuit range/performance | – |
P279F | Four wheel drive control – signal low | – |
P27A0 | Four wheel drive control – signal high | – |
P2800 | Transmission range (TR) sensor B – PRNDL input | Wiring, TR sensor, TCM |
P2801 | Transmission range (TR) sensor B – circuit range/performance | Wiring, TR sensor, TCM |
P2802 | Transmission range (TR) sensor B – circuit low | Wiring, TR sensor, TCM |
P2803 | Transmission range (TR) sensor B – circuit high | Wiring, TR sensor, TCM |
P2804 | Transmission range (TR) sensor B – circuit intermittent | Wiring, TR sensor, TCM |
P2805 | Transmission range (TR) sensor A/B – correlation | Wiring, TR sensor, TCM |
P2806 | Transmission range (TR) sensor – TR sensor misaligned | Wiring, TR sensor, TCM |
P2807 | Transmission fluid pressure (TFP) solenoid G | – |
Transmission fluid pressure (TFP) solenoid G – performance | Wiring, TFP solenoid, transmission mechanical fault, | |
P2808 | ||
problem or solenoid stuck off | ECM | |
Transmission fluid pressure (TFP) solenoid G – solenoid stuck | Wiring, TFP solenoid, transmission mechanical fault, | |
P2809 | ||
on | ECM | |
P280A | Transmission range (TR) sensor A – calibration not learned | – |
P280B | Transmission range (TR) sensor B – calibration not learned | – |
P2810 | Transmission fluid pressure (TFP) solenoid G – electrical | Wiring, TFP solenoid, ECM |
P2811 | Transmission fluid pressure (TFP) solenoid G – intermittent | Wiring, TFP solenoid, ECM |
Transmission fluid pressure (TFP) solenoid G – control circuit | ||
P2812 | Wiring, TFP solenoid, ECM | |
open | ||
Transmission fluid pressure (TFP) solenoid G – control circuit | ||
P2813 | Wiring, TFP solenoid, ECM | |
range/performance | ||
Transmission fluid pressure (TFP) solenoid G – control circuit | ||
P2814 | Wiring, TFP solenoid, ECM | |
low | ||
Transmission fluid pressure (TFP) solenoid G – control circuit | ||
P2815 | Wiring, TFP solenoid, ECM | |
high | ||
P2816 | Transmission fluid pressure (TFP) solenoid H | – |
Transmission fluid pressure (TFP) solenoid H – performance or | Wiring, TFP solenoid, transmission mechanical fault, | |
P2817 | ||
stuck off | ECM | |
Transmission fluid pressure (TFP) solenoid H – solenoid stuck | Wiring, TFP solenoid, transmission mechanical fault, | |
P2818 | ||
on | ECM | |
P2819 | Transmission fluid pressure (TFP) solenoid H – electrical | Wiring, TFP solenoid, ECM |
P281A | Transmission fluid pressure (TFP) solenoid H – intermittent | Wiring, TFP solenoid, ECM |
Transmission fluid pressure (TFP) solenoid H – control circuit | ||
P281B | Wiring, TFP solenoid, ECM | |
open | ||
Transmission fluid pressure (TFP) solenoid H – control circuit | ||
P281C | Wiring, TFP solenoid, ECM | |
range/performance | ||
Transmission fluid pressure (TFP) solenoid H – control circuit | ||
P281D | Wiring, TFP solenoid, ECM | |
low | ||
Transmission fluid pressure (TFP) solenoid H – control circuit | ||
P281E | Wiring, TFP solenoid, ECM | |
high | ||
P281F | Transmission fluid pressure (TFP) solenoid J – malfunction | Wiring, TFP solenoid, ECM |
Transmission fluid pressure (TFP) solenoid J – performance or | Wiring, TFP solenoid, transmission mechanical fault, | |
P2820 | ||
stuck off | ECM | |
Transmission fluid pressure (TFP) solenoid J – solenoid stuck | Wiring, TFP solenoid, transmission mechanical fault, | |
P2821 | ||
on | ECM | |
P2822 | Transmission fluid pressure (TFP) solenoid J – electrical | Wiring, TFP solenoid, ECM |
P2823 | Transmission fluid pressure (TFP) solenoid J – intermittent | Wiring, TFP solenoid, ECM |
Transmission fluid pressure (TFP) solenoid J – control circuit | ||
P2824 | Wiring, TFP solenoid, ECM | |
open | ||
Transmission fluid pressure (TFP) solenoid J – control circuit | ||
P2825 | Wiring, TFP solenoid, ECM | |
range/performance | ||
Transmission fluid pressure (TFP) solenoid J – control circuit | ||
P2826 | Wiring, TFP solenoid, ECM | |
low | ||
Transmission fluid pressure (TFP) solenoid J – control circuit | ||
P2827 | Wiring, TFP solenoid, ECM | |
high | ||
P2828 | Transmission fluid pressure (TFP) solenoid K | – |
Transmission fluid pressure (TFP) solenoid K – performance or | Wiring, TFP solenoid, transmission mechanical fault, | |
P2829 | ||
stuck off | ECM | |
Transmission fluid pressure (TFP) solenoid K – solenoid stuck | Wiring, TFP solenoid, transmission mechanical fault, | |
P282A | ||
on | ECM | |
P282B | Transmission fluid pressure (TFP) solenoid K – electrical | Wiring, TFP solenoid, ECM |
P282C | Transmission fluid pressure (TFP) solenoid K – intermittent | Wiring, TFP solenoid, ECM |
Transmission fluid pressure (TFP) solenoid K – control circuit | ||
P282D | Wiring, TFP solenoid, ECM | |
open | ||
Transmission fluid pressure (TFP) solenoid K – control circuit | ||
P282E | Wiring, TFP solenoid, ECM | |
range/performance | ||
Transmission fluid pressure (TFP) solenoid K – control circuit | ||
P282F | Wiring, TFP solenoid, ECM | |
low | ||
Transmission fluid pressure (TFP) solenoid K – control circuit | ||
P2830 | Wiring, TFP solenoid, ECM | |
high | ||
P2831 | Transmission shift fork A position – circuit malfunction | – |
P2832 | Transmission shift fork A position – circuit range/performance | – |
P2833 | Transmission shift fork A position – signal low | – |
P2834 | Transmission shift fork A position – signal high | – |
P2835 | Transmission shift fork A position – intermittent signal | – |
P2836 | Transmission shift fork B position – circuit malfunction | – |
P2837 | Transmission shift fork B position – circuit range/performance | – |
P2838 | Transmission shift fork B position – signal low | – |
P2839 | Transmission shift fork B position – signal high | – |
P283A | Transmission shift fork B position – intermittent signal | – |
P283B | Transmission shift fork C position – circuit malfunction | – |
P283C | Transmission shift fork C position – circuit range/performance | – |
P283D | Transmission shift fork C position – signal low | – |
P283E | Transmission shift fork C position – signal high | – |
P283F | Transmission shift fork C position – intermittent signal | – |
P2840 | Transmission shift fork D position – circuit malfunction | – |
P2841 | Transmission shift fork D position – circuit range/performance | – |
P2842 | Transmission shift fork D position – signal low | – |
P2843 | Transmission shift fork D position – signal high | – |
P2844 | Transmission shift fork D position – intermittent signal | – |
Transmission shift fork A position sensor – incorrect neutral | ||
P2845 | – | |
position indicated | ||
Transmission shift fork B position sensor – incorrect neutral | ||
P2846 | – | |
position indicated | ||
Transmission shift fork C position sensor – incorrect neutral | ||
P2847 | – | |
position indicated | ||
Transmission shift fork D position sensor – incorrect neutral | ||
P2848 | – | |
position indicated | ||
P2849 | Transmission shift fork A – shift fork stuck | – |
P284A | Transmission shift fork B – shift fork stuck | – |
P284B | Transmission shift fork C – shift fork stuck | – |
P284C | Transmission shift fork D – shift fork stuck | – |
P284D | Transmission shift fork A – unrequested movement | – |
P284E | Transmission shift fork B – unrequested movement | – |
P284F | Transmission shift fork C – unrequested movement | – |
P2850 | Transmission shift fork D – unrequested movement | – |
P2851 | Transmission shift fork position sensor – A/B correlation | – |
P2852 | Transmission shift fork position sensor – C/D correlation | – |
P2853 | Clutch A – pressure discharge performance | – |
P2854 | Clutch B – pressure discharge performance | – |
P2855 | Clutch A – pressure charge performance | – |
P2856 | Clutch B – pressure charge performance | – |
P2857 | Clutch A – pressure engagement performance | – |
P2858 | Clutch B – pressure engagement performance | – |
P2859 | Clutch A – pressure disengagement performance | – |
P285A | Clutch B – pressure disengagement performance | – |
P285B | Transmission shift fork actuator A – open circuit | Wiring, transmission shift fork actuator |
P285C | Transmission shift fork actuator A – circuit performance | Wiring, transmission shift fork actuator |
P285D | Transmission shift fork actuator A – circuit low | Wiring, transmission shift fork actuator |
P285E | Transmission shift fork actuator A – circuit high | Wiring, transmission shift fork actuator |
P285F | Transmission shift fork actuator B – open circuit | Wiring, transmission shift fork actuator |
P2860 | Transmission shift fork actuator B – circuit performance | Wiring, transmission shift fork actuator |
P2861 | Transmission shift fork actuator B – circuit low | Wiring, transmission shift fork actuator |
P2862 | Transmission shift fork actuator B – circuit high | Wiring, transmission shift fork actuator |
Heated oxygen sensor (HO2S) 1, bank 1 – circuit | ||
P2A00 | Wiring, HO2S, ECM | |
range/performance | ||
Heated oxygen sensor (HO2S) 2, bank 1 – circuit | ||
P2A01 | Wiring, HO2S, ECM | |
range/performance | ||
Heated oxygen sensor (HO2S) 3, bank 1 – circuit | ||
P2A02 | Wiring, HO2S, ECM | |
range/performance | ||
Heated oxygen sensor (HO2S) 1, bank 2 – circuit | ||
P2A03 | Wiring, HO2S, ECM | |
range/performance | ||
Heated oxygen sensor (HO2S) 2, bank 2 – circuit | ||
P2A04 | Wiring, HO2S, ECM | |
range/performance | ||
Heated oxygen sensor (HO2S) 3, bank 2 – circuit | ||
P2A05 | Wiring, HO2S, ECM | |
range/performance | ||
Heated oxygen sensor (HO2S) 1, bank 1 – circuit negative | ||
P2A06 | Wiring, HO2S, ECM | |
voltage | ||
Heated oxygen sensor (HO2S) 2, bank 1 – circuit negative | ||
P2A07 | Wiring, HO2S, ECM | |
voltage | ||
Heated oxygen sensor (HO2S) 3, bank 1 – circuit negative | ||
P2A08 | Wiring, HO2S, ECM | |
voltage | ||
Heated oxygen sensor (HO2S) 1, bank 2 – circuit negative | ||
P2A09 | Wiring, HO2S, ECM | |
voltage | ||
Heated oxygen sensor (HO2S) 2, bank 2 – circuit negative | ||
P2A10 | Wiring, HO2S, ECM | |
voltage | ||
Heated oxygen sensor (HO2S) 3, bank 2 – circuit negative | ||
P2A11 | Wiring, HO2S, ECM | |
voltage | ||
P2BA7 | Nitrogen oxides (NOx), limit exceeded – reductant tank empty | Wiring, NOx sensor, ECM |
Nitrogen oxides (NOx), limit exceeded – interruption of | ||
P2BA8 | Wiring, NOx sensor, ECM | |
reductant metering | ||
Nitrogen oxides (NOx), limit exceeded – insufficient reductant | ||
P2BA9 | Wiring, NOx sensor, ECM | |
quality | ||
Nitrogen oxides (NOx), limit exceeded – low reductant | ||
P2BAA | Wiring, NOx sensor, ECM | |
consumption | ||
Wiring, NOx sensor, EGR valve/EGR valve actuator, | ||
P2BAB | Nitrogen oxides (NOx), limit exceeded – incorrect EGR flow | |
ECM | ||
Wiring, NOx sensor, EGR valve/EGR valve actuator, | ||
P2BAC | Nitrogen oxides (NOx), limit exceeded – EGR deactivated | |
ECM | ||
P2BAD | Nitrogen oxides (NOx), limit exceeded – cause unknown | – |
P2BAE | Nitrogen oxides (NOx), limit exceeded – NOx control monitoring | Wiring, NOx sensor, ECM |
EOBD | ||
Fault location | Probable cause | |
code | ||
P0000 | No fault found | – |
P0001 | Fuel volume regulator control – open circuit | Wiring, regulator control solenoid |
P0002 | Fuel volume regulator control – circuit range/performance | Wiring, regulator control solenoid |
P0003 | Fuel volume regulator control – circuit low | Wiring short to earth, regulator control solenoid |
Wiring open circuit/short to positive, regulator control | ||
P0004 | Fuel volume regulator control – circuit high | |
solenoid | ||
P0005 | Fuel shut-off valve – open circuit | Wiring open circuit, fuel shut-off valve |
P0006 | Fuel shut-off valve – circuit low | Wiring short to earth, fuel shut-off valve |
P0007 | Fuel shut-off valve – circuit high | Wiring short to positive, fuel shut-off valve |
P0008 | Engine position system, bank 1 – engine performance | Mechanical fault |
P0009 | Engine position system, bank 2 – engine performance | Mechanical fault |
P000A | Intake camshaft position A, bank 1 – slow response | Wiring, mechanical fault, ECM |
P000B | Exhaust camshaft position B, bank 1 – slow response | Wiring, mechanical fault, ECM |
P000C | Intake camshaft position A, bank 2 – slow response | Wiring, mechanical fault, ECM |
P000D | Exhaust camshaft position B, bank 2 – slow response | Wiring, mechanical fault, ECM |
P000E | Fuel quantity adjuster control – learning limit exceeded | Wiring, fuel quantity adjuster, injectors, ECM |
P000F | Fuel system over pressure relief valve activated | Wiring, mechanical fault, ECM |
Camshaft position (CMP) actuator, intake/left/front, bank 1 – | ||
P0010 | Wiring, CMP actuator, ECM | |
circuit malfunction | ||
Camshaft position (CMP), intake/left/front, bank 1 – timing | ||
P0011 | Valve timing, engine mechanical fault, CMP actuator | |
over-advanced/system performance | ||
Camshaft position (CMP), intake/left/front, bank 1 – timing | ||
P0012 | Valve timing, engine mechanical fault, CMP actuator | |
over-retarded | ||
Camshaft position (CMP) actuator, intake/left/front, bank 1 – | ||
P0013 | Wiring, CMP actuator, ECM | |
circuit malfunction | ||
Camshaft position (CMP) actuator, exhaust/right/rear, bank 1 | ||
P0014 | Valve timing, engine mechanical fault, CMP actuator | |
– timing over-advanced/system performance | ||
Camshaft position (CMP) actuator, exhaust/right/rear, bank 1 | ||
P0015 | Valve timing, engine mechanical fault, CMP actuator | |
– timing over-retarded | ||
Crankshaft position/camshaft position, bank 1 sensor A – | ||
P0016 | Wiring, CKP sensor, CMP sensor, mechanical fault | |
correlation | ||
Crankshaft position/camshaft position, bank 1 sensor B – | ||
P0017 | Wiring, CKP sensor, CMP sensor, mechanical fault | |
correlation | ||
Crankshaft position/camshaft position, bank 2 sensor A – | ||
P0018 | Wiring, CKP sensor, CMP sensor, mechanical fault | |
correlation | ||
Crankshaft position/camshaft position, bank 2 sensor B – | ||
P0019 | Wiring, CKP sensor, CMP sensor, mechanical fault | |
correlation | ||
P001A | Intake camshaft profile control A, bank 1 – open circuit | Wiring, mechanical fault, ECM |
P001B | Intake camshaft profile control A, bank 1 – circuit low | Wiring, ECM |
P001C | Intake camshaft profile control A – bank 1 – circuit high | Wiring, mechanical fault, ECM |
P001D | Intake camshaft profile control A, bank 2 – open circuit | Wiring, mechanical fault, ECM |
P001E | Intake camshaft profile control A, bank 2 – circuit low | Wiring, mechanical fault, ECM |
P001F | Intake camshaft profile control A, bank 2 – circuit high | Wiring, ECM |
Camshaft position (CMP) actuator, intake/left/front, bank 2 – | ||
P0020 | Wiring, CMP actuator, ECM | |
circuit malfunction | ||
Camshaft position (CMP), intake/left/front, bank 2 – timing | ||
P0021 | Valve timing, engine mechanical fault, CMP actuator | |
over-advanced/system performance | ||
Camshaft position (CMP), intake/left/front, bank 2 – timing | ||
P0022 | Valve timing, engine mechanical fault, CMP actuator | |
over-retarded | ||
Camshaft position (CMP) actuator, exhaust/right/rear, bank 2 | ||
P0023 | Wiring, CMP actuator, ECM | |
– circuit malfunction | ||
Camshaft position (CMP), exhaust/right/rear, bank 2 – timing | ||
P0024 | Valve timing, engine mechanical fault, CMP actuator | |
over-advanced/system performance | ||
Camshaft position (CMP), exhaust/right/rear, bank 2 – timing | ||
P0025 | Valve timing, engine mechanical fault, CMP actuator | |
over-retarded | ||
Intake valve control solenoid, bank 1 – range/performance | ||
P0026 | Wiring, intake valve control solenoid | |
problem | ||
Exhaust valve control solenoid, bank 1 – range/performance | ||
P0027 | Wiring, exhaust valve control solenoid | |
problem | ||
Intake valve control solenoid, bank 2 – range/performance | ||
P0028 | Wiring, intake valve control solenoid | |
problem | ||
Exhaust valve control solenoid, bank 2 – range/performance | ||
P0029 | Wiring, exhaust valve control solenoid | |
problem | ||
P002A | Exhaust camshaft profile control B, bank 1 – open circuit | Wiring, ECM |
P002B | Exhaust camshaft profile control B, bank 1 – circuit low | Wiring, ECM |
P002C | Exhaust camshaft profile control B, bank 1 – circuit high | Wiring, mechanical fault, ECM |
P002D | Exhaust camshaft profile control B, bank 2 – open circuit | Wiring, mechanical fault, ECM |
P002E | Exhaust camshaft profile control B, bank 2 – circuit low | Wiring, mechanical fault, ECM |
P002F | Exhaust camshaft profile control B, bank 2 – circuit high | Wiring, mechanical fault, ECM |
Heated oxygen sensor (HO2S) 1, bank 1, heater control – | ||
P0030 | Wiring, HO2S, ECM | |
circuit malfunction | ||
Heated oxygen sensor (HO2S) 1, bank 1, heater control – | ||
P0031 | Wiring short to earth, HO2S, ECM | |
circuit low | ||
Heated oxygen sensor (HO2S) 1, bank 1, heater control – | ||
P0032 | Wiring short to positive, HO2S, ECM | |
circuit high | ||
P0033 | Turbocharger (TC) bypass valve – circuit malfunction | Wiring, TC wastegate regulating valve, ECM |
Wiring short to earth, TC wastegate regulating valve, | ||
P0034 | Turbocharger (TC) bypass valve – circuit low | |
ECM | ||
Wiring short to positive, TC wastegate regulating valve, | ||
P0035 | Turbocharger (TC) bypass valve – circuit high | |
ECM | ||
Heated oxygen sensor (HO2S) 2, bank 1, heater control – | ||
P0036 | Wiring, HO2S, ECM | |
circuit malfunction | ||
Heated oxygen sensor (HO2S) 2, bank 1, heater control – | ||
P0037 | Wiring short to earth, HO2S, ECM | |
circuit low | ||
Heated oxygen sensor (HO2S) 2, bank 1, heater control – | ||
P0038 | Wiring short to positive, HO2S, ECM | |
circuit high | ||
Turbocharger (TC) bypass valve/supercharger (SC) bypass | ||
P0039 | Wiring, bypass valve | |
valve, control – range/performance problem | ||
Turbocharger (TC)/supercharger (SC) boost pressure control | Wiring, TC/SC boost control solenoid, TC/SC boost | |
P003A | ||
A – learning limit exceeded | pressure actuator, ECM | |
Turbocharger (TC)/supercharger (SC) boost pressure control | Wiring, TC/SC boost control solenoid, TC/SC boost | |
P003B | ||
B – learning limit exceeded | pressure actuator, ECM | |
Intake camshaft profile control A, bank 1 – performance or | ||
P003C | Wiring, mechanical fault, ECM | |
stuck off | ||
P003D | Intake camshaft profile control A, bank 1 – stuck on | Wiring, mechanical fault, ECM |
Intake camshaft profile control A, bank 2 – performance | ||
P003E | Wiring, mechanical fault, ECM | |
problem or stuck off | ||
P003F | Intake camshaft profile control A, bank 2 – stuck on | Wiring, mechanical fault, ECM |
Oxygen sensor signals swapped, bank 1 sensor 1/bank 2 | ||
P0040 | Wiring | |
sensor 1 | ||
Oxygen sensor signals swapped, bank 1 sensor 2/bank 2 | ||
P0041 | Wiring | |
sensor 2 | ||
Heated oxygen sensor (HO2S) 3, bank 1, heater control – | ||
P0042 | Wiring, HO2S, ECM | |
circuit malfunction | ||
Heated oxygen sensor (HO2S) 3, bank 1, heater control – | ||
P0043 | Wiring short to earth, HO2S, ECM | |
circuit low | ||
Heated oxygen sensor (HO2S) 3, bank 1, heater control – | ||
P0044 | Wiring short to positive, HO2S, ECM | |
circuit high | ||
Turbocharger (TC) boost control solenoid/supercharger (SC) | ||
P0045 | Wiring, TC/SC boost control solenoid | |
boost control solenoid – open circuit | ||
Turbocharger (TC) boost control solenoid/supercharger (SC) | ||
P0046 | Wiring, TC/SC boost control solenoid, mechanical fault | |
boost control solenoid – circuit range/performance | ||
Turbocharger (TC) boost control solenoid/supercharger (SC) | ||
P0047 | Wiring short to earth, TC/SC boost control solenoid | |
boost control solenoid – circuit low | ||
Turbocharger (TC) boost control solenoid/supercharger (SC) | ||
P0048 | Wiring short to positive, TC/SC boost control solenoid | |
boost control solenoid – circuit high | ||
P0049 | Turbocharger (TC)/supercharger (SC) turbine – over-speed | Mechanical fault |
Turbocharger (TC)/supercharger (SC) boost pressure control | Wiring, TC/SC boost control solenoid, TC/SC boost | |
P004A | ||
B – open circuit | pressure actuator, ECM | |
Turbocharger (TC)/supercharger (SC) boost pressure control | Wiring, TC/SC boost control solenoid, TC/SC boost | |
P004B | ||
B – circuit range/performance | pressure actuator, ECM | |
Turbocharger (TC)/supercharger (SC) boost pressure control | Wiring, TC/SC boost control solenoid, TC/SC boost | |
P004C | ||
B – circuit low | pressure actuator, ECM | |
Turbocharger (TC)/supercharger (SC) boost pressure control | Wiring, TC/SC boost control solenoid, TC/SC boost | |
P004D | ||
B – circuit high | pressure actuator, ECM | |
Turbocharger (TC)/supercharger (SC) boost pressure control | Wiring, TC/SC boost control solenoid, TC/SC boost | |
P004E | ||
A – circuit intermittent/erratic | pressure actuator, ECM | |
Turbocharger (TC)/supercharger (SC) boost pressure control | Wiring, TC/SC boost control solenoid, TC/SC boost | |
P004F | ||
B – circuit intermittent/erratic | pressure actuator, ECM | |
Heated oxygen sensor (HO2S) 1, bank 2, heater control – | ||
P0050 | Wiring, HO2S, ECM | |
circuit malfunction | ||
Heated oxygen sensor (HO2S) 1, bank 2, heater control – | ||
P0051 | Wiring short to earth, HO2S, ECM | |
circuit low | ||
Heated oxygen sensor (HO2S) 1, bank 2, heater control – | ||
P0052 | Wiring short to positive, HO2S, ECM | |
circuit high | ||
Heated oxygen sensor (HO2S), bank 1, sensor 1 – heater | ||
P0053 | Wiring, HO2S | |
resistance | ||
Heated oxygen sensor (HO2S), bank 1, sensor 2 – heater | ||
P0054 | Wiring, HO2S | |
resistance | ||
Heated oxygen sensor (HO2S), bank 1, sensor 3 – heater | ||
P0055 | Wiring, HO2S | |
resistance | ||
Heated oxygen sensor (HO2S) 2, bank 2, heater control – | ||
P0056 | Wiring, HO2S, ECM | |
circuit malfunction | ||
Heated oxygen sensor (HO2S) 2, bank 2, heater control – | ||
P0057 | Wiring short to earth, HO2S, ECM | |
heater circuit low | ||
Heated oxygen sensor (HO2S) 2, bank 2, heater control – | ||
P0058 | Wiring short to positive, HO2S, ECM | |
circuit high | ||
Heated oxygen sensor (HO2S), bank 2, sensor 1 – heater | ||
P0059 | Wiring, HO2S | |
resistance | ||
Exhaust camshaft profile control B, bank 1 – performance or | ||
P005A | Wiring, mechanical fault, ECM | |
stuck off | ||
P005B | Exhaust camshaft profile control B, bank 1 – stuck on | Wiring, mechanical fault, ECM |
Exhaust camshaft profile control B, bank 2 – performance or | ||
P005C | Wiring, mechanical fault, ECM | |
stuck off | ||
P005D | Exhaust camshaft profile control B, bank 2 – stuck on | Wiring, mechanical fault, ECM |
Turbocharger (TC)/supercharger (SC) boost pressure control | Wiring, TC/SC boost control solenoid, TC/SC boost | |
P005E | ||
B – supply voltage low | pressure actuator, ECM | |
Turbocharger (TC)/supercharger (SC) boost pressure control | Wiring, TC/SC boost control solenoid, TC/SC boost | |
P005F | ||
B – supply voltage high | pressure actuator, ECM | |
Heated oxygen sensor (HO2S), bank 2, sensor 2 – heater | ||
P0060 | Wiring, HO2S | |
resistance | ||
Heated oxygen sensor (HO2S), bank 2, sensor 3 – heater | ||
P0061 | Wiring, HO2S | |
resistance | ||
Heated oxygen sensor (HO2S) 3, bank 2, heater control – | ||
P0062 | Wiring, HO2S, ECM | |
circuit malfunction | ||
Heated oxygen sensor (HO2S) 3, bank 2, heater control – | ||
P0063 | Wiring short to earth, HO2S, ECM | |
circuit low | ||
Heated oxygen sensor (HO2S) 3, bank 2, heater control – | ||
P0064 | Wiring short to positive, HO2S, ECM | |
circuit high | ||
P0065 | Air assisted injector – range/performance problem | Air assisted injector |
P0066 | Air assisted injector – circuit malfunction/circuit low | Wiring short to earth, air assisted injector, ECM |
P0067 | Air assisted injector – circuit high | Wiring short to positive, air assisted injector, ECM |
Manifold absolute pressure (MAP) sensor/mass air flow | ||
P0068 | Wiring, MAP sensor, MAF sensor, mechanical fault | |
(MAF) sensor – throttle position correlation | ||
Manifold absolute pressure (MAP) sensor/barometric | ||
P0069 | MAP sensor, mechanical fault | |
pressure (BARO) sensor – correlation | ||
P006A | MAP sensor/MAF or VAF sensor bank 1 – correlation | Wiring, MAP sensor, MAF sensor, VAF sensor, ECM |
Manifold absolute pressure (MAP) sensor/exhaust pressure – | ||
P006B | Wiring, MAP sensor, exhaust gas pressure sensor, ECM | |
correlation | ||
MAP sensor/turbocharger (TC)/supercharger (SC) boost | ||
P006C | Wiring, TC/SC boost pressure sensor, ECM | |
pressure sensor – correlation | ||
Barometric pressure (BARO)/turbocharger (TC)/supercharger | Wiring, BARO sensor, TC/SC intake pressure sensor, | |
P006D | ||
(SC) intake pressure – correlation | mechanical fault, ECM | |
Turbocharger (TC)/supercharger (SC) boost pressure control | Wiring, TC/SC boost control solenoid, TC/SC boost | |
P006E | ||
A – supply voltage low | pressure actuator, ECM | |
Turbocharger (TC)/supercharger (SC) boost pressure control | Wiring, TC/SC boost control solenoid, TC/SC boost | |
P006F | ||
A – supply voltage high | pressure actuator, ECM | |
P0070 | Outside air temperature sensor – circuit malfunction | Wiring, outside air temperature sensor, ECM |
P0071 | Outside air temperature sensor – range/performance problem | Outside air temperature sensor |
Wiring short to earth, outside air temperature sensor, | ||
P0072 | Outside air temperature sensor – low input | |
ECM | ||
Wiring short to positive, outside air temperature sensor, | ||
P0073 | Outside air temperature sensor – high input | |
ECM | ||
Wiring, poor connection, outside air temperature sensor, | ||
P0074 | Outside air temperature sensor – circuit intermittent | |
ECM | ||
P0075 | Intake valve control solenoid, bank 1 – circuit malfunction | Wiring, intake valve control solenoid, ECM |
P0076 | Intake valve control solenoid, bank 1 – circuit low | Wiring short to earth, intake valve control solenoid, ECM |
Wiring short to positive, intake valve control solenoid, | ||
P0077 | Intake valve control solenoid, bank 1 – circuit high | |
ECM | ||
P0078 | Exhaust valve control solenoid, bank 1 – circuit malfunction | Wiring, exhaust valve control solenoid, ECM |
Wiring short to earth, exhaust valve control solenoid, | ||
P0079 | Exhaust valve control solenoid, bank 1 – circuit low | |
ECM | ||
Turbocharger (TC) intercooler temperature sensor, bank 1 – | ||
P007A | Wiring, TC intercooler temperature sensor, ECM | |
circuit malfunction | ||
Turbocharger (TC) intercooler temperature sensor, bank 1 – | ||
P007B | Wiring, TC intercooler temperature sensor, ECM | |
circuit range/performance | ||
Turbocharger (TC) intercooler temperature sensor, bank 1 – | ||
P007C | Wiring, TC intercooler temperature sensor, ECM | |
circuit low | ||
Turbocharger (TC) intercooler temperature sensor, bank 1 – | ||
P007D | Wiring, TC intercooler temperature sensor, ECM | |
circuit high | ||
Turbocharger (TC) intercooler temperature sensor, bank 1 – | ||
P007E | Wiring, TC intercooler temperature sensor, ECM | |
circuit intermittent/erratic | ||
Turbocharger (TC) intercooler temperature sensor, bank 1/2 – | ||
P007F | Wiring, TC intercooler temperature sensor, ECM | |
correlation | ||
Wiring short to positive, exhaust valve control solenoid, | ||
P0080 | Exhaust valve control solenoid, bank 1 – circuit high | |
ECM | ||
P0081 | Intake valve control solenoid, bank 2 – circuit malfunction | Wiring, intake valve control solenoid, ECM |
P0082 | Intake valve control solenoid, bank 2 – circuit low | Wiring short to earth, intake valve control solenoid, ECM |
Wiring short to positive, intake valve control solenoid, | ||
P0083 | Intake valve control solenoid, bank 2 – circuit high | |
ECM | ||
P0084 | Exhaust valve control solenoid, bank 2 – circuit malfunction | Wiring, exhaust valve control solenoid, ECM |
Wiring short to earth, exhaust valve control solenoid, | ||
P0085 | Exhaust valve control solenoid, bank 2 – circuit low | |
ECM | ||
Wiring short to positive, exhaust valve control solenoid, | ||
P0086 | Exhaust valve control solenoid, bank 2 – circuit high | |
ECM | ||
Fuel pump, fuel pressure regulator, fuel supply pipe | ||
P0087 | Fuel rail/system pressure too low | |
blockage, mechanical fault | ||
Fuel pump, fuel pressure regulator, fuel return pipe | ||
P0088 | Fuel rail/system pressure too high | |
blockage, mechanical fault | ||
P0089 | Fuel pressure regulator 1 – performance problem | Fuel pressure regulator, mechanical fault |
Wiring, fuel pump (FP), restricted fuel supply, fuel | ||
P008A | Low pressure fuel system – pressure too low | |
pressure control valve | ||
P008B | Low pressure fuel system – pressure too high | Fuel pressure relief valve |
P008C | Fuel cooling pump motor control – open circuit | Wiring, fuel cooling pump motor, ECM |
P008D | Fuel cooling pump motor – circuit low | Wiring, fuel cooling pump motor, ECM |
P008E | Fuel cooling pump motor – control circuit high | Wiring, fuel cooling pump motor, ECM |
Engine coolant temperature (ECT)/fuel temperature – | ||
P008F | Wiring, ECT sensor, fuel temperature sensor, ECM | |
correlation | ||
P0090 | Fuel pressure regulator 1 – open circuit | Wiring open circuit, fuel metering solenoid, ECM |
P0091 | Fuel pressure regulator 1 – short to earth | Wiring short to earth, fuel metering solenoid, ECM |
P0092 | Fuel pressure regulator 1 – short to positive | Wiring short to positive, fuel metering solenoid, ECM |
P0093 | Fuel system leak – large leak detected | Wiring, fuel pressure sensor, mechanical fault |
P0094 | Fuel system leak – small leak detected | Wiring, fuel pressure sensor, mechanical fault |
P0095 | Intake air temperature (IAT) sensor 2 – circuit malfunction | Wiring, poor connection, IAT sensor, ECM |
Intake air temperature (IAT) sensor 2 – circuit | ||
P0096 | Wiring, poor connection, IAT sensor, ECM | |
range/performance | ||
P0097 | Intake air temperature (IAT) sensor 2 – circuit low input | Wiring short to earth, IAT sensor, ECM |
P0098 | Intake air temperature (IAT) sensor 2 – circuit high input | Wiring short to positive, IAT sensor, ECM |
Intake air temperature (IAT) sensor 2 – circuit | ||
P0099 | Wiring, poor connection, IAT sensor, ECM | |
intermittent/erratic | ||
Intake air temperature (IAT)/outside air temperature – | ||
P009A | Wiring, IAT sensor, outside air temperature sensor, ECM | |
correlation | ||
P009B | Fuel pressure relief system – control circuit open | Wiring, fuel pressure relief valve, ECM |
P009C | Fuel pressure relief system – control circuit low | Wiring, fuel pressure relief valve, ECM |
P009D | Fuel pressure relief system – control circuit high | Wiring, fuel pressure regulator control solenoid, ECM |
Fuel pressure relief system – performance problem or stuck | ||
P009E | Wiring, fuel pressure relief valve, mechanical fault, ECM | |
off | ||
P009F | Fuel pressure relief system – valve stuck | Wiring, fuel pressure relief valve, ECM |
Turbocharger (TC) intercooler temperature sensor, bank 2 – | ||
P00A0 | Wiring, TC intercooler temperature sensor, ECM | |
circuit malfunction | ||
Turbocharger (TC) intercooler temperature sensor, bank 2 – | ||
P00A1 | Wiring, TC intercooler temperature sensor, ECM | |
circuit range/performance | ||
Turbocharger (TC) intercooler temperature sensor bank 2 – | ||
P00A2 | Wiring, TC intercooler temperature sensor, ECM | |
circuit low | ||
Turbocharger (TC) intercooler temperature sensor, bank 2 – | ||
P00A3 | Wiring, TC intercooler temperature sensor, ECM | |
circuit high | ||
Turbocharger (TC) intercooler temperature sensor – circuit | ||
P00A4 | Wiring, TC intercooler temperature sensor, ECM | |
intermittent/erratic, bank 2 | ||
Intake air temperature (IAT) sensor 2, bank 2 – circuit | ||
P00A5 | Wiring, IAT sensor, ECM | |
malfunction | ||
Intake air temperature (IAT) sensor 2, bank 2 – circuit | ||
P00A6 | Wiring, IAT sensor, ECM | |
range/performance | ||
P00A7 | Intake air temperature (IAT) sensor 2, bank 2 – circuit low | Wiring, IAT sensor, ECM |
P00A8 | Intake air temperature (IAT) sensor 2, bank 2 – circuit high | Wiring, IAT sensor, ECM |
Intake air temperature (IAT) sensor 2, bank 2 – circuit | ||
P00A9 | Wiring, IAT sensor, ECM | |
intermittent/erratic | ||
Intake air temperature (IAT) sensor 1, bank 2 – circuit | ||
P00AA | Wiring, IAT sensor, ECM | |
malfunction | ||
Intake air temperature (IAT) sensor 1, bank 2 – circuit | ||
P00AB | Wiring, IAT sensor, ECM | |
range/performance | ||
P00AC | Intake air temperature (IAT) sensor 1, bank 2 – circuit low | Wiring, IAT sensor, ECM |
P00AD | Intake air temperature (IAT) sensor 1, bank 2 – circuit high | Wiring, IAT sensor, ECM |
Intake air temperature (IAT) sensor 1, bank 2 – circuit | ||
P00AE | Wiring, IAT sensor, ECM | |
intermittent/erratic | ||
Turbocharger (TC)/supercharger (SC) boost pressure control | ||
P00AF | Wiring, ECM | |
A – module performance | ||
Turbocharger (TC)/supercharger (SC) boost pressure control | ||
P00B0 | ECM | |
B – module performance | ||
P00B1 | Radiator coolant temperature sensor – circuit malfunction | Wiring, radiator coolant temperature sensor, ECM |
Radiator coolant temperature sensor – circuit | ||
P00B2 | Wiring, radiator coolant temperature sensor, ECM | |
range/performance | ||
P00B3 | Radiator coolant temperature sensor – circuit low | Wiring, radiator coolant temperature sensor, ECM |
P00B4 | Radiator coolant temperature sensor – circuit high | Wiring, radiator coolant temperature sensor, ECM |
Radiator coolant temperature sensor – circuit | ||
P00B5 | Wiring, radiator coolant temperature sensor, ECM | |
intermittent/erratic | ||
Radiator coolant temperature/engine coolant temperature | Wiring, radiator coolant temperature sensor, ECT sensor, | |
P00B6 | ||
(ECT) – correlation | ECM | |
P00B7 | Engine coolant flow low – performance problem | Thermostat, radiator, engine coolant pump |
Wiring, MAP sensor, MAF sensor, VAF sensor, hose | ||
P00B8 | MAP sensor/MAF sensor or VAF sensor, bank 2 – correlation | |
blocked/leaking – ECM | ||
Wiring, low ambient temperature, fuel system pressure | ||
P00B9 | Fuel system pressure sensor – pressure too low | |
sensor | ||
P00BA | Fuel pressure low – forced limited power mode | – |
P00BB | Injector, insufficient flow detected – forced limited power mode | – |
P00BC | Mass air flow (MAF) sensor A – circuit range/performance | Wiring, MAF sensor |
P00BD | Mass air flow (MAF) sensor A – circuit range/performance | Wiring, MAF sensor |
P00BE | Mass air flow (MAF) sensor B – circuit range/performance | Wiring, MAF sensor |
P00BF | Mass air flow (MAF) sensor B – circuit range/performance | Wiring, MAF sensor |
Turbocharger (TC)/supercharger (SC) bypass valve B – | ||
P00C0 | Wiring, TC/SC bypass valve | |
control circuit | ||
Turbocharger (TC)/supercharger (SC) bypass valve B – circuit | ||
P00C1 | Wiring, TC/SC bypass valve | |
low | ||
P00C2 | Turbocharger (TC)/supercharger (SC) B – circuit high | Wiring, TC/SC bypass valve |
Turbocharger (TC)/supercharger (SC) B – circuit | ||
P00C3 | Wiring, TC/SC bypass valve | |
range/performance | ||
Turbocharger (TC)/supercharger (SC) bypass valve B – | ||
P00C4 | – | |
mechanical fault | ||
Turbocharger (TC)/supercharger (SC) B – turbine shaft over | ||
P00C5 | – | |
speed condition | ||
Fuel level low, fuel leak/blockage, fuel pump (FP), | ||
P00C6 | Fuel rail pressure (FRP) – engine cranking – pressure too low | |
injector(s) | ||
Intake air pressure measurement system – multiple sensor | ||
P00C7 | Wiring, ECM | |
correlation | ||
P00C8 | Fuel pressure regulator control solenoid – open circuit | Wiring, fuel pressure regulator control solenoid, ECM |
P00C9 | Fuel pressure regulator control solenoid – circuit low | Wiring, fuel pressure regulator control solenoid, ECM |
P00CA | Fuel pressure regulator control solenoid – circuit high | Wiring, fuel pressure regulator control solenoid, ECM |
P00CB | Fuel quantity adjuster – open circuit | Wiring, fuel quantity adjuster, ECM |
P00CC | Fuel quantity adjuster – circuit low | Wiring, fuel quantity adjuster, ECM |
P00CD | Fuel quantity adjuster – circuit high | Wiring, fuel quantity adjuster, ECM |
Intake air temperature (IAT) measurement system – multiple | ||
P00CE | Wiring, IAT sensor(s), ECM | |
sensor correlation | ||
Barometric pressure (BARO) sensor/turbocharger | Wiring, BARO sensor, TC/SC boost pressure sensor, | |
P00CF | ||
(TC)/supercharger (SC) boost pressure sensor A – correlation | ECM | |
Barometric pressure (BARO) sensor/turbocharger | Wiring, BARO sensor, TC/SC boost pressure sensor, | |
P00D0 | ||
(TC)/supercharger (SC) boost pressure sensor B – correlation | ECM | |
Mass air flow (MAF) sensor/volume air flow (VAF) sensor – | ||
P0100 | Wiring, MAF/VAF sensor, ECM | |
circuit malfunction | ||
Mass air flow (MAF) sensor/volume air flow (VAF) sensor – | ||
P0101 | Intake leak/blockage, MAF/VAF sensor | |
range/performance problem | ||
Mass air flow (MAF) sensor/volume air flow (VAF) sensor – | ||
P0102 | Wiring short to earth, MAF/VAF sensor, ECM | |
low input | ||
Mass air flow (MAF) sensor/volume air flow (VAF) sensor – | ||
P0103 | Wiring short to positive, MAF/VAF sensor, ECM | |
high input | ||
Mass air flow (MAF) sensor/volume air flow (VAF) sensor – | ||
P0104 | Wiring, poor connection, MAF/VAF sensor, ECM | |
circuit intermittent | ||
Manifold absolute pressure (MAP) sensor/barometric | ||
P0105 | Wiring, MAP sensor, BARO sensor, ECM | |
pressure (BARO) sensor – circuit malfunction | ||
Manifold absolute pressure (MAP) sensor/barometric | ||
P0106 | Intake/exhaust leak, wiring, MAP sensor, BARO sensor | |
pressure (BARO) sensor – range/performance problem | ||
Manifold absolute pressure (MAP) sensor/barometric | ||
P0107 | Wiring short to earth, MAP sensor, BARO sensor, ECM | |
pressure (BARO) sensor – low input | ||
Manifold absolute pressure (MAP) sensor/barometric | Wiring short to positive, MAP sensor, BARO sensor, | |
P0108 | ||
pressure (BARO) sensor – high input | ECM | |
Manifold absolute pressure (MAP) sensor/barometric | Wiring, poor connection, MAP sensor, BARO sensor, | |
P0109 | ||
pressure (BARO) sensor – circuit intermittent | ECM | |
P010A | MAF sensor or VAF sensor B – circuit malfunction | Wiring, MAF sensor, VAF sensor, ECM |
Exhaust gas recirculation (EGR) control module B – | ||
P010B | Wiring, EGR control module, ECM | |
communication malfunction | ||
P010B | MAF sensor or VAF sensor B – circuit range/performance | Wiring, MAF sensor, VAF sensor, ECM |
P010C | MAF sensor or VAF sensor B – circuit low | Wiring, MAF sensor, VAF sensor, ECM |
P010D | MAF sensor or VAF sensor B – circuit high | Wiring, MAF sensor, VAF sensor, ECM |
P010E | MAF sensor or VAF sensor B – circuit intermittent/erratic | Wiring, MAF sensor, VAF sensor, ECM |
P010F | MAF sensor or VAF sensor A/B – correlation | Wiring, MAF sensor, VAF sensor, ECM |
P0110 | Intake air temperature (IAT) sensor – circuit malfunction | Wiring, IAT sensor, ECM |
Intake air temperature (IAT) sensor – range/performance | ||
P0111 | IAT sensor | |
problem | ||
P0112 | Intake air temperature (IAT) sensor – low input | Wiring short to earth, IAT sensor, ECM |
Wiring open circuit/short to positive, earth wire defective, | ||
P0113 | Intake air temperature (IAT) sensor – high input | |
IAT sensor, ECM | ||
P0114 | Intake air temperature (IAT) sensor – circuit intermittent | Wiring, poor connection, IAT sensor, ECM |
P0115 | Engine coolant temperature (ECT) sensor – circuit malfunction | Wiring, ECT sensor, ECM |
Engine coolant temperature (ECT) sensor – | ||
P0116 | Coolant thermostat, poor connection, wiring, ECT sensor | |
range/performance problem | ||
P0117 | Engine coolant temperature (ECT) sensor – low input | Coolant thermostat, wiring short to earth, ECT sensor |
Coolant thermostat, wiring open circuit/short to positive, | ||
P0118 | Engine coolant temperature (ECT) sensor – high input | |
earth wire defective, ECT sensor | ||
P0119 | Engine coolant temperature (ECT) sensor – circuit intermittent | Wiring, poor connection, ECT sensor, ECM |
P011A | Engine coolant temperature (ECT) sensor 1/2 – correlation | Wiring, ECT sensor, ECM |
Engine coolant temperature (ECT)/intake air temperature | ||
P011B | Wiring, ECT sensor, IAT sensor, ECM | |
(IAT) – correlation | ||
Charge air temperature/intake air temperature (IAT), bank 1 – | Wiring, IAT sensor, TC/SC boost air temperature sensor, | |
P011C | ||
correlation | ECM | |
Charge air temperature/intake air temperature (IAT), bank 2 – | Wiring, IAT sensor, TC/SC boost air temperature sensor, | |
P011D | ||
correlation | ECM | |
Engine coolant temperature (ECT) sensor 1/outside air | Wiring, ECT sensor, outside air temperature sensor, | |
P011E | ||
temperature sensor – correlation | ECM | |
Engine coolant temperature (ECT) sensor 2/outside air | Wiring, ECT sensor, outside air temperature sensor, | |
P011F | ||
temperature sensor – correlation | ECM | |
Throttle position (TP) sensor A/accelerator pedal position | ||
P0120 | Wiring, TP/APP sensor, ECM | |
(APP) sensor A – circuit malfunction | ||
Throttle position (TP) switch A/accelerator pedal position | ||
P0120 | Wiring, TP switch, APP switch, ECM | |
(APP) switch A – circuit malfunction | ||
Throttle position (TP) sensor A/accelerator pedal position | ||
P0121 | Accelerator cable adjustment, TP/APP sensor | |
(APP) sensor A – range/performance problem | ||
Throttle position (TP) switch A/accelerator pedal position | ||
P0121 | Accelerator cable adjustment, TP switch, APP switch | |
(APP) switch A – range/performance problem | ||
Throttle position (TP) sensor A/accelerator pedal position | ||
P0122 | Wiring short to earth, TP/APP sensor, ECM | |
(APP) sensor A – low input | ||
Throttle position (TP) switch A/accelerator pedal position | ||
P0122 | Wiring short to earth, TP switch, APP switch, ECM | |
(APP) switch A – low input | ||
Throttle position (TP) sensor A/accelerator pedal position | ||
P0123 | Wiring short to positive, TP/APP sensor, ECM | |
(APP) sensor A – high input | ||
Throttle position (TP) switch A/accelerator pedal position | ||
P0123 | Wiring short to positive, TP switch, APP switch, ECM | |
(APP) switch A – high input | ||
Throttle position (TP) sensor A/accelerator pedal position | ||
P0124 | Wiring, poor connection, TP/APP sensor, ECM | |
(APP) sensor A – circuit intermittent | ||
Throttle position (TP) switch A/accelerator pedal position | ||
P0124 | Wiring, poor connection, TP switch, APP switch, ECM | |
(APP) switch A – circuit intermittent | ||
Wiring, engine cooling system, coolant thermostat, ECT | ||
P0125 | Insufficient coolant temperature for closed loop fuel control | |
sensor | ||
Wiring, engine cooling system, coolant thermostat, ECT | ||
P0126 | Insufficient coolant temperature for stable operation | |
sensor | ||
Wiring short to earth, IAT sensor 2, mechanical fault, | ||
P0127 | Intake air temperature too high | |
ECM | ||
Coolant thermostat – coolant temperature below thermostat | ||
P0128 | Mechanical fault | |
regulating temperature | ||
P0129 | Barometric pressure too low | Wiring, BARO sensor, mechanical fault |
Turbocharger (TC)/supercharger (SC) intake pressure sensor | ||
P012A | Wiring, TC/SC intake pressure sensor, ECM | |
– circuit malfunction | ||
Turbocharger (TC)/supercharger (SC) intake pressure sensor | ||
P012B | Wiring, TC/SC intake pressure sensor, ECM | |
– circuit range/performance | ||
Turbocharger (TC)/supercharger (SC) intake pressure sensor | ||
P012C | Wiring, TC/SC intake pressure sensor, ECM | |
– circuit low | ||
Turbocharger (TC)/supercharger (SC) intake pressure sensor | ||
P012D | Wiring, TC/SC intake pressure sensor, ECM | |
– circuit high | ||
Turbocharger (TC)/supercharger (SC) intake pressure sensor | ||
P012E | Wiring, TC/SC intake pressure sensor, ECM | |
– circuit intermittent/erratic | ||
P0130 | Heated oxygen sensor (HO2S) 1, bank 1 – circuit malfunction | Heating inoperative, poor connection, wiring, HO2S |
P0130 | Oxygen sensor (O2S) 1, bank 1 – circuit malfunction | Wiring, O2S, ECM |
P0131 | Heated oxygen sensor (HO2S) 1, bank 1 – low voltage | Exhaust leak, wiring short to earth, HO2S, ECM |
P0131 | Oxygen sensor (O2S) 1, bank 1 – low voltage | Exhaust leak, wiring short to earth, O2S, ECM |
P0132 | Heated oxygen sensor (HO2S) 1, bank 1 – high voltage | Wiring short to positive, HO2S, ECM |
P0132 | Oxygen sensor (O2S) 1, bank 1 – high voltage | Wiring short to positive, O2S, ECM |
P0133 | Heated oxygen sensor (HO2S) 1, bank 1 – slow response | Heating inoperative, wiring, HO2S |
P0133 | Oxygen sensor (O2S) 1, bank 1 – slow response | Wiring, O2S |
Heated oxygen sensor (HO2S) 1, bank 1 – no activity | ||
P0134 | Wiring open circuit, heating inoperative, HO2S | |
detected | ||
P0134 | Oxygen sensor (O2S) 1, bank 1 – no activity detected | Wiring, O2S |
Heated oxygen sensor (HO2S) 1, bank 1, heater control – | ||
P0135 | Fuse, wiring, HO2S, ECM | |
circuit malfunction | ||
P0136 | Heated oxygen sensor (HO2S) 2, bank 1 – circuit malfunction | Heating inoperative, wiring, HO2S, ECM |
P0136 | Oxygen sensor (O2S) 2, bank 1 – circuit malfunction | Wiring, O2S, ECM |
P0137 | Heated oxygen sensor (HO2S) 2, bank 1 – low voltage | Exhaust leak, wiring short to earth, HO2S, ECM |
P0137 | Oxygen sensor (O2S) 2, bank 1 – low voltage | Exhaust leak, wiring short to earth, O2S, ECM |
P0138 | Heated oxygen sensor (HO2S) 2, bank 1 – high voltage | Wiring short to positive, HO2S, ECM |
P0138 | Oxygen sensor (O2S) 2, bank 1 – high voltage | Wiring short to positive, O2S, ECM |
P0139 | Heated oxygen sensor (HO2S) 2, bank 1 – slow response | Heating inoperative, wiring, HO2S |
P0139 | Oxygen sensor (O2S) 2, bank 1 – slow response | Wiring, O2S |
Heated oxygen sensor (HO2S) 2, bank 1 – slow response rich | ||
P013A | Wiring, HO2S, ECM | |
to lean | ||
Heated oxygen sensor (HO2S) 2, bank 1 – slow response | ||
P013B | Wiring, HO2S, ECM | |
lean to rich | ||
Heated oxygen sensor (HO2S) 2, bank 2 – slow response rich | ||
P013C | Wiring, HO2S, ECM | |
to lean | ||
Heated oxygen sensor (HO2S) 2, bank 2 – slow response | ||
P013D | Wiring, HO2S, ECM | |
lean to rich | ||
Heated oxygen sensor (HO2S) 2, bank 1 – delayed response | ||
P013E | Wiring, HO2S, ECM | |
rich to lean | ||
Heated oxygen sensor (HO2S) 2, bank 1 – delayed response | ||
P013F | Wiring, HO2S, ECM | |
lean to rich | ||
Heated oxygen sensor (HO2S) 2, bank 1 – no activity | ||
P0140 | Wiring, heating inoperative, HO2S, ECM | |
detected | ||
P0140 | Oxygen sensor (O2S) 2, bank 1 – no activity detected | Wiring, O2S, ECM |
Heated oxygen sensor (HO2S) 2, bank 1, heater control – | ||
P0141 | Wiring, HO2S, ECM | |
circuit malfunction | ||
P0142 | Heated oxygen sensor (HO2S) 3, bank 1 – circuit malfunction | Wiring, HO2S, ECM |
P0143 | Heated oxygen sensor (HO2S) 3, bank 1 – low voltage | Exhaust leak, wiring short to earth, HO2S, ECM |
P0143 | Oxygen sensor (O2S) 3, bank 1 – low voltage | Exhaust leak, wiring short to earth, O2S, ECM |
P0144 | Heated oxygen sensor (HO2S) 3, bank 1 – high voltage | Wiring short to positive, HO2S, ECM |
P0144 | Oxygen sensor (O2S) 3, bank 1 – high voltage | Wiring short to positive, O2S, ECM |
P0145 | Heated oxygen sensor (HO2S) 3, bank 1 – slow response | Heating inoperative, wiring, HO2S |
P0145 | Oxygen sensor (O2S) 3, bank 1 – slow response | Wiring, O2S |
Heated oxygen sensor (HO2S) 3, bank 1 – no activity | ||
P0146 | Wiring, HO2S, ECM | |
detected | ||
P0146 | Oxygen sensor (O2S) 3, bank 1 – no activity detected | Wiring, O2S, ECM |
Heated oxygen sensor (HO2S) 3, bank 1, heater control – | ||
P0147 | Wiring, HO2S, ECM | |
circuit malfunction | ||
P0148 | Fuel delivery error | Fuel pump/fuel injection pump |
P0149 | Fuel timing error | Fuel pump/fuel injection pump |
Heated oxygen sensor (HO2S) 2, bank 2 – delayed response | ||
P014A | Wiring, HO2S, ECM | |
rich to lean | ||
Heated oxygen sensor (HO2S) 2, bank 2 – delayed response | ||
P014B | Wiring, HO2S, ECM | |
lean to rich | ||
Heated oxygen sensor (HO2S) 1, bank 1 – slow response rich | ||
P014C | Wiring, HO2S | |
to lean | ||
Heated oxygen sensor (HO2S) 1, bank 1 – slow response | ||
P014D | Wiring, HO2S | |
lean to rich | ||
Heated oxygen sensor (HO2S) 1, bank 2 – slow response rich | ||
P014E | Wiring, HO2S | |
to lean | ||
Heated oxygen sensor (HO2S) 1, bank 2 – slow response | ||
P014F | Wiring, HO2S | |
lean to rich | ||
P0150 | Heated oxygen sensor (HO2S) 1, bank 2 – circuit malfunction | Wiring, HO2S, ECM |
P0150 | Oxygen sensor (O2S) 1, bank 2 – circuit malfunction | Wiring, O2S, ECM |
P0151 | Heated oxygen sensor (HO2S) 1, bank 2 – low voltage | Exhaust leak, wiring short to earth, HO2S, ECM |
Heated oxygen sensor (HO2S) 1, bank 1 – delayed response | ||
P015A | Wiring, HO2S | |
rich to lean | ||
Heated oxygen sensor (HO2S) 1, bank 1 – delayed response | ||
P015B | Wiring, HO2S | |
lean to rich | ||
Heated oxygen sensor (HO2S) 1, bank 2 – delayed response | ||
P015C | Wiring, HO2S | |
rich to lean | ||
Heated oxygen sensor (HO2S) 1, bank 2 – delayed response | ||
P015D | Wiring, HO2S | |
lean to rich | ||
P015D | Oxygen sensor (O2S) 1, bank 2 – low voltage | Exhaust leak, wiring short to earth, O2S, ECM |
P0152 | Heated oxygen sensor (HO2S) 1, bank 2 – high voltage | Wiring short to positive, HO2S, ECM |
P0152 | Oxygen sensor (O2S) 1, bank 2 – high voltage | Wiring short to positive, O2S, ECM |
P0153 | Heated oxygen sensor (HO2S) 1, bank 2 – slow response | Heating inoperative, wiring, HO2S |
P0153 | Oxygen sensor (O2S) 1, bank 2 – slow response | Wiring, O2S |
Heated oxygen sensor (HO2S) 1, bank 2 – no activity | ||
P0154 | Wiring, HO2S, ECM | |
detected | ||
P0154 | Oxygen sensor (O2S) 1, bank 2 – no activity detected | Wiring, O2S, ECM |
Heated oxygen sensor (HO2S) 1, bank 2, heater control – | ||
P0155 | Wiring, HO2S, ECM | |
circuit malfunction | ||
P0156 | Heated oxygen sensor (HO2S) 2, bank 2 – circuit malfunction | Heating inoperative, wiring, HO2S, ECM |
P0156 | Oxygen sensor (O2S) 2, bank 2 – circuit malfunction | Wiring, O2S, ECM |
P0157 | Heated oxygen sensor (HO2S) 2, bank 2 – low voltage | Exhaust leak, wiring short to earth, HO2S, ECM |
P0157 | Oxygen sensor (O2S) 2, bank 2 – low voltage | Exhaust leak, wiring short to earth, O2S, ECM |
P0158 | Heated oxygen sensor (HO2S) 2, bank 2 – high voltage | Wiring short to positive, HO2S, ECM |
P0158 | Oxygen sensor (O2S) 2, bank 2 – high voltage | Wiring short to positive, O2S, ECM |
P0159 | Heated oxygen sensor (HO2S) 2, bank 2 – slow response | Heating inoperative, wiring, HO2S |
P0159 | Oxygen sensor (O2S) 2, bank 2 – slow response | Wiring, O2S |
Heated oxygen sensor (HO2S) 2, bank 2 – no activity | ||
P0160 | Wiring, HO2S, ECM | |
detected | ||
P0160 | Oxygen sensor (O2S) 2, bank 2 – no activity detected | Wiring, O2S, ECM |
Heated oxygen sensor (HO2S) 2, bank 2, heater control – | ||
P0161 | Wiring, HO2S, ECM | |
circuit malfunction | ||
P0162 | Heated oxygen sensor (HO2S) 3, bank 2 – circuit malfunction | Wiring, HO2S, ECM |
P0162 | Oxygen sensor (O2S) 3, bank 2 – circuit malfunction | Wiring, O2S, ECM |
P0163 | Heated oxygen sensor (HO2S) 3, bank 2 – low voltage | Exhaust leak, wiring short to earth, HO2S, ECM |
P0163 | Oxygen sensor (O2S) 3, bank 2 – low voltage | Exhaust leak, wiring short to earth, O2S, ECM |
P0164 | Heated oxygen sensor (HO2S) 3, bank 2 – high voltage | Wiring short to positive, HO2S, ECM |
P0164 | Oxygen sensor (O2S) 3, bank 2 – high voltage | Wiring short to positive, O2S, ECM |
P0165 | Heated oxygen sensor (HO2S) 3, bank 2 – slow response | Heating inoperative, wiring, HO2S |
P0165 | Oxygen sensor (O2S) 3, bank 2 – slow response | Wiring, O2S |
Heated oxygen sensor (HO2S) 3, bank 2 – no activity | ||
P0166 | Wiring, HO2S, ECM | |
detected | ||
P0166 | Oxygen sensor (O2S) 3, bank 2 – no activity detected | Wiring, O2S, ECM |
Heated oxygen sensor (HO2S) 3, bank 2, heater control – | ||
P0167 | Wiring, HO2S, ECM | |
circuit malfunction | ||
P0168 | Fuel temperature too high | Wiring, fuel temperature sensor, mechanical fault |
P0169 | Incorrect fuel composition | Wiring, fuel composition sensor, mechanical fault |
P016A | Excessive time to enter closed loop mixture control | – |
P016B | Closed loop mixture control, limit reached – system too rich | – |
P016C | Closed loop mixture control, limit reached – system too lean | – |
P016D | Excessive time to enter closed loop fuel pressure control | – |
Closed loop fuel pressure control, limit reached – pressure too | ||
P016E | – | |
high | ||
Closed loop fuel pressure control, limit reached – pressure too | ||
P016F | – | |
low | ||
Intake leak, AIR system, fuel pressure/pump, injector(s), | ||
P0170 | Fuel trim (FT), bank 1 – malfunction | |
EVAP canister purge valve, HO2S | ||
Intake/exhaust leak, AIR system, MAF/VAF sensor, fuel | ||
P0171 | System too lean, bank 1 | |
pressure/pump, injector(s), HO2S | ||
Intake blocked, EVAP canister purge valve, fuel | ||
P0172 | System too rich, bank 1 | |
pressure, EGR system, injector(s), HO2S | ||
Intake leak, AIR system, fuel pressure/pump, injector(s), | ||
P0173 | Fuel trim (FT), bank 2 – malfunction | |
EVAP canister purge valve, HO2S | ||
Intake/exhaust leak, fuel pressure/pump, injector(s), AIR | ||
P0174 | System too lean, bank 2 | |
system, hose connection(s) | ||
Intake blocked, EVAP canister purge valve, fuel | ||
P0175 | System too rich, bank 2 | |
pressure, EGR system, injector(s), HO2S | ||
P0176 | Fuel composition sensor – circuit malfunction | Wiring, fuel composition sensor, ECM |
P0177 | Fuel composition sensor – range/performance problem | Fuel composition sensor |
P0178 | Fuel composition sensor – low input | Wiring short to earth, fuel composition sensor, ECM |
P0179 | Fuel composition sensor – high input | Wiring short to positive, fuel composition sensor, ECM |
P017A | Cylinder head temperature (CHT) sensor – circuit malfunction | Wiring, CHT sensor, ECM |
Cylinder head temperature (CHT) sensor – circuit | ||
P017B | Wiring, CHT sensor, ECM | |
range/performance | ||
P017C | Cylinder head temperature (CHT) sensor – circuit low | Wiring, CHT sensor, ECM |
P017D | Cylinder head temperature (CHT) sensor – circuit high | Wiring, CHT sensor, ECM |
Cylinder head temperature (CHT) sensor – circuit | ||
P017E | Wiring, CHT sensor, ECM | |
intermittent/erratic | ||
P0180 | Fuel temperature sensor A – circuit malfunction | Wiring, fuel temperature sensor, ECM |
P0181 | Fuel temperature sensor A – range/performance problem | Fuel temperature sensor |
P0182 | Fuel temperature sensor A – low input | Wiring short to earth, fuel temperature sensor, ECM |
P0183 | Fuel temperature sensor A – high input | Wiring short to positive, fuel temperature sensor, ECM |
P0184 | Fuel temperature sensor A – circuit intermittent | Wiring, poor connection, fuel temperature sensor, ECM |
P0185 | Fuel temperature sensor B – circuit malfunction | Wiring, fuel temperature sensor, ECM |
P0186 | Fuel temperature sensor B – range/performance problem | Fuel temperature sensor |
P0187 | Fuel temperature sensor B – low input | Wiring short to earth, fuel temperature sensor, ECM |
P0188 | Fuel temperature sensor B – high input | Wiring short to positive, fuel temperature sensor, ECM |
P0189 | Fuel temperature sensor B – circuit intermittent | Wiring, poor connection, fuel temperature sensor, ECM |
P018A | Fuel pressure sensor B – circuit malfunction | Wiring, fuel pressure sensor, ECM |
P018B | Fuel pressure sensor B – circuit range/performance | Wiring, fuel pressure sensor, ECM |
P018C | Fuel pressure sensor B – circuit low | Wiring, fuel pressure sensor, ECM |
P018D | Fuel pressure sensor B – circuit high | Wiring, fuel pressure sensor, ECM |
P018E | Fuel pressure sensor B – circuit intermittent/erratic | Wiring, fuel pressure sensor, ECM |
P018F | Fuel pressure relief system – frequent activation | – |
P0190 | Fuel rail pressure (FRP) sensor – circuit malfunction | Wiring, FRP sensor, ECM |
P0191 | Fuel rail pressure (FRP) sensor – range/performance problem | Wiring, FRP sensor |
P0192 | Fuel rail pressure (FRP) sensor – low input | Wiring short to earth, FRP sensor |
P0193 | Fuel rail pressure (FRP) sensor – high input | Wiring short to positive, FRP sensor |
P0194 | Fuel rail pressure (FRP) sensor – circuit intermittent | Wiring, poor connection, FRP sensor |
P0195 | Engine oil temperature (EOT) sensor – circuit malfunction | Wiring, EOT sensor, ECM |
Engine oil temperature (EOT) sensor – range/performance | ||
P0196 | EOT sensor | |
problem | ||
P0197 | Engine oil temperature (EOT) sensor – low input | Wiring short to earth, EOT sensor |
P0198 | Engine oil temperature (EOT) sensor – high input | Wiring short to positive, EOT sensor |
P0199 | Engine oil temperature (EOT) sensor – circuit intermittent | Wiring, poor connection, EOT sensor, ECM |
P0200 | Injector – circuit malfunction | Wiring, injector, ECM |
P0201 | Injector 1 – circuit malfunction | Wiring, injector, ECM |
P0202 | Injector 2 – circuit malfunction | Wiring, injector, ECM |
P0203 | Injector 3 – circuit malfunction | Wiring, injector, ECM |
P0204 | Injector 4 – circuit malfunction | Wiring, injector, ECM |
P0205 | Injector 5 – circuit malfunction | Wiring, injector, ECM |
P0206 | Injector 6 – circuit malfunction | Wiring, injector, ECM |
P0207 | Injector 7 – circuit malfunction | Wiring, injector, ECM |
P0208 | Injector 8 – circuit malfunction | Wiring, injector, ECM |
P0209 | Injector 9 – circuit malfunction | Wiring, injector, ECM |
P020A | Injection timing, cylinder 1 | CKP sensor, CMP sensor, mechanical fault |
P020B | Injection timing, cylinder 2 | CKP sensor, CMP sensor, mechanical fault |
P020C | Injection timing, cylinder 3 | CKP sensor, CMP sensor, mechanical fault |
P020D | Injection timing, cylinder 4 | CKP sensor, CMP sensor, mechanical fault |
P020E | Injection timing, cylinder 5 | CKP sensor, CMP sensor, mechanical fault |
P020F | Injection timing, cylinder 6 | CKP sensor, CMP sensor, mechanical fault |
P0210 | Injector 10 – circuit malfunction | Wiring, injector, ECM |
P0211 | Injector 11 – circuit malfunction | Wiring, injector, ECM |
P0212 | Injector 12 – circuit malfunction | Wiring, injector, ECM |
P0213 | Cold start injector 1 – circuit malfunction | Wiring, cold start injector, ECM |
P0214 | Cold start injector 2 – circuit malfunction | Wiring, cold start injector, ECM |
P0215 | Fuel shut-off solenoid – circuit malfunction | Wiring, fuel shut-off solenoid, ECM |
P0216 | Fuel injection timing control – circuit malfunction | Wiring, fuel injection timing control solenoid, ECM |
Wiring, engine cooling system, coolant thermostat, ECT | ||
P0217 | Engine over temperature condition | |
sensor | ||
P0218 | Transmission over temperature condition | Wiring, TFT sensor, ECM |
P0219 | Engine over speed condition | Incorrect gear change |
P021A | Injection timing, cylinder 7 | CKP sensor, CMP sensor, mechanical fault |
P021B | Injection timing, cylinder 8 | CKP sensor, CMP sensor, mechanical fault |
P021C | Injection timing, cylinder 9 | CKP sensor, CMP sensor, mechanical fault |
P021D | Injection timing, cylinder 10 | CKP sensor, CMP sensor, mechanical fault |
P021E | Injection timing, cylinder 11 | CKP sensor, CMP sensor, mechanical fault |
P021F | Injection timing, cylinder 12 | CKP sensor, CMP sensor, mechanical fault |
Throttle position (TP) sensor B/accelerator pedal position | ||
P0220 | Wiring, TP/APP sensor, ECM | |
(APP) sensor B – circuit malfunction | ||
Throttle position (TP) switch B/accelerator pedal position | ||
P0220 | Wiring, TP switch, APP switch, ECM | |
(APP) switch B – circuit malfunction | ||
Throttle position (TP) sensor B/accelerator pedal position | ||
P0221 | Accelerator cable adjustment, TP/APP sensor | |
(APP) sensor B – range/performance problem | ||
Throttle position (TP) switch B/accelerator pedal position | ||
P0221 | Accelerator cable adjustment, TP switch, APP switch | |
(APP) switch B – range/performance problem | ||
Throttle position (TP) sensor B/accelerator pedal position | ||
P0222 | Wiring short to earth, TP/APP sensor, ECM | |
(APP) sensor B – low input | ||
Throttle position (TP) switch B/accelerator pedal position | ||
P0222 | Wiring short to earth, TP switch, APP switch, ECM | |
(APP) switch B – low input | ||
Throttle position (TP) sensor B/accelerator pedal position | ||
P0223 | Wiring short to positive, TP/APP sensor, ECM | |
(APP) sensor B – high input | ||
Throttle position (TP) switch B/accelerator pedal position | ||
P0223 | Wiring short to positive, TP switch, APP switch, ECM | |
(APP) switch B – high input | ||
Throttle position (TP) sensor B/accelerator pedal position | ||
P0224 | Wiring, poor connection, TP/APP sensor, ECM | |
(APP) sensor B – circuit intermittent | ||
Throttle position (TP) switch B/accelerator pedal position | ||
P0224 | Wiring, poor connection, TP switch, APP switch, ECM | |
(APP) switch B – circuit intermittent | ||
Throttle position (TP) sensor C/accelerator pedal position | ||
P0225 | Wiring, TP/APP sensor, ECM | |
(APP) sensor C – circuit malfunction | ||
Throttle position (TP) switch C/accelerator pedal position | ||
P0225 | Wiring, TP switch, APP switch, ECM | |
(APP) switch C – circuit malfunction | ||
Throttle position (TP) sensor C/accelerator pedal position | ||
P0226 | Accelerator cable adjustment, TP/APP sensor | |
(APP) sensor C – range/performance problem | ||
Throttle position (TP) switch C/accelerator pedal position | ||
P0226 | Accelerator cable adjustment, TP switch, APP switch | |
(APP) switch C – range/performance problem | ||
Throttle position (TP) sensor C/accelerator pedal position | ||
P0227 | Wiring short to earth, TP/APP sensor, ECM | |
(APP) sensor C – low input | ||
Throttle position (TP) switch C/accelerator pedal position | ||
P0227 | Wiring short to earth, TP switch, APP switch, ECM | |
(APP) switch C – low input | ||
Throttle position (TP) sensor C/accelerator pedal position | ||
P0228 | Wiring short to positive, TP/APP sensor, ECM | |
(APP) sensor C – high input | ||
Throttle position (TP) switch C/accelerator pedal position | ||
P0228 | Wiring short to positive, TP switch, APP switch, ECM | |
(APP) switch C – high input | ||
Throttle position (TP) sensor C/accelerator pedal position | ||
P0229 | Wiring, poor connection, TP/APP sensor, ECM | |
(APP) sensor C – circuit intermittent | ||
Throttle position (TP) switch C/accelerator pedal position | ||
P0229 | Wiring, poor connection, TP switch, APP switch, ECM | |
(APP) switch C – circuit intermittent | ||
Turbocharger (TC) intercooler bypass actuator A – open | ||
P022A | Wiring, TC intercooler bypass actuator, ECM | |
circuit | ||
Turbocharger (TC) intercooler bypass actuator control A – | ||
P022B | Wiring, TC intercooler bypass actuator, ECM | |
circuit low | ||
P022C | Turbocharger (TC) intercooler bypass actuator A – circuit high | Wiring, TC intercooler bypass actuator, ECM |
Turbocharger (TC) intercooler bypass actuator control B – | ||
P022D | Wiring, TC intercooler bypass actuator, ECM | |
open circuit | ||
Turbocharger (TC) intercooler bypass actuator control B – | ||
P022E | Wiring, TC intercooler bypass actuator, ECM | |
circuit low | ||
Turbocharger (TC) intercooler bypass actuator control B – | ||
P022F | Wiring, TC intercooler bypass actuator, ECM | |
circuit high | ||
P0230 | Fuel pump relay – circuit malfunction | Wiring, fuel pump relay, ECM |
P0231 | Fuel pump relay – circuit low | Wiring short to earth, fuel pump relay, ECM |
P0232 | Fuel pump relay – circuit high | Wiring short to positive, fuel pump relay, ECM |
P0233 | Fuel pump relay – circuit intermittent | Wiring, poor connection, fuel pump relay, ECM |
Hose connection(s), wiring, TC wastegate regulating | ||
P0234 | Turbocharger (TC), engine boost condition – limit exceeded | |
valve, TC wastegate | ||
P0234 | Supercharger (SC), engine boost condition – limit exceeded | Wiring, SC bypass valve/motor, SC |
Manifold absolute pressure (MAP) sensor A, TC system – | ||
P0235 | Wiring, MAP sensor | |
circuit malfunction | ||
Turbocharger (TC) boost pressure sensor A/supercharger | ||
P0235 | Wiring, TC/SC boost pressure sensor | |
(SC) boost pressure sensor A – circuit malfunction | ||
Manifold absolute pressure (MAP) sensor A, TC system – | ||
P0236 | Intake/exhaust leak, hose connection(s), MAP sensor | |
range/performance problem | ||
Turbocharger (TC) boost pressure sensor A/supercharger | Intake/exhaust leak, hose connection(s), TC/SC boost | |
P0236 | ||
(SC) boost pressure sensor A – range/performance problem | pressure sensor | |
Manifold absolute pressure (MAP) sensor A, TC system – low | ||
P0237 | Wiring short to earth, MAP sensor, ECM | |
input | ||
Turbocharger (TC) boost pressure sensor/supercharger (SC) | Wiring short to earth, TC/SC boost pressure sensor, | |
P0237 | ||
boost pressure sensor A – low input | ECM | |
Manifold absolute pressure (MAP) sensor A, TC system – | ||
P0238 | Wiring short to positive, MAP sensor, ECM | |
high input | ||
Turbocharger (TC) boost pressure sensor A/supercharger | Wiring short to positive, TC/SC boost pressure sensor, | |
P0238 | ||
(SC) boost pressure sensor A – high input | ECM | |
Manifold absolute pressure (MAP) sensor B, TC system – | ||
P0239 | Wiring, MAP sensor, ECM | |
circuit malfunction | ||
Turbocharger (TC) boost pressure sensor B/supercharger | ||
P0239 | Wiring, TC/SC boost pressure sensor, ECM | |
(SC) boost pressure sensor – circuit malfunction | ||
P023A | Turbocharger (TC) intercooler coolant pump – open circuit | Wiring, TC intercooler coolant pump, ECM |
P023B | Turbocharger (TC) intercooler coolant pump – circuit low | Wiring, TC intercooler coolant pump, ECM |
Turbocharger (TC) intercooler coolant pump – control circuit | ||
P023C | Wiring, TC intercooler coolant pump, ECM | |
high | ||
Manifold absolute pressure (MAP) sensor/turbocharger | ||
P023D | Wiring, MAP sensor, TC/SC boost pressure sensor, ECM | |
(TC)/supercharger (SC) boost pressure sensor A – correlation | ||
Manifold absolute pressure (MAP) sensor/turbocharger | ||
P023E | Wiring, MAP sensor, TC/SC boost pressure sensor, ECM | |
(TC)/supercharger (SC) boost pressure sensor B – correlation | ||
P023F | Fuel pump (FP), secondary – open circuit | Wiring, fuel pump (FP), fuel pump relay, ECM |
Manifold absolute pressure (MAP) sensor B, TC system – | ||
P0240 | Intake/exhaust leak, hose connection(s), MAP sensor | |
range/performance problem | ||
Turbocharger (TC) boost pressure sensor B/supercharger | Intake/exhaust leak, hose connection(s), TC/SC boost | |
P0240 | ||
(SC) boost pressure sensor B – range/performance problem | pressure sensor | |
Manifold absolute pressure (MAP) sensor B, TC system – low | ||
P0241 | Wiring short to earth, MAP sensor, ECM | |
input | ||
Turbocharger (TC) boost pressure sensor B/supercharger | Wiring short to earth, TC/SC boost pressure sensor, | |
P0241 | ||
(SC) boost pressure sensor B – low input | ECM | |
Manifold absolute pressure (MAP) sensor B, TC system – | ||
P0242 | Wiring short to positive, MAP sensor, ECM | |
high input | ||
Turbocharger (TC) boost pressure sensor B/supercharger | Wiring short to positive, TC/SC boost pressure sensor, | |
P0242 | ||
(SC) boost pressure sensor B – high input | ECM | |
P0243 | Supercharger (SC) bypass valve A – circuit malfunction | Wiring, SC bypass valve, ECM |
Turbocharger (TC) wastegate regulating valve A – circuit | ||
P0243 | Wiring, TC wastegate regulating valve, ECM | |
malfunction | ||
Supercharger (SC) bypass valve A – range/performance | ||
P0244 | SC bypass valve | |
problem | ||
Turbocharger (TC) wastegate regulating valve A – | ||
P0244 | TC wastegate regulating valve | |
range/performance problem | ||
P0245 | Supercharger (SC) bypass valve A – circuit low | Wiring short to earth, SC bypass valve, ECM |
Wiring short to earth, TC wastegate regulating valve, | ||
P0245 | Turbocharger (TC) wastegate regulating valve A – circuit low | |
ECM | ||
P0246 | Supercharger (SC) bypass valve A – circuit high | Wiring short to positive, SC bypass valve, ECM |
Wiring short to positive, TC wastegate regulating valve, | ||
P0246 | Turbocharger (TC) wastegate regulating valve A – circuit high | |
ECM | ||
P0247 | Supercharger (SC) bypass valve B – circuit malfunction | Wiring, SC bypass valve, ECM |
Turbocharger (TC) wastegate regulating valve B – circuit | ||
P0247 | Wiring, TC wastegate regulating valve, ECM | |
malfunction | ||
Supercharger (SC) bypass valve B – range/performance | ||
P0248 | SC bypass valve | |
problem | ||
Turbocharger (TC) wastegate regulating valve B – | ||
P0248 | TC wastegate regulating valve | |
range/performance problem | ||
P0249 | Supercharger (SC) bypass valve B – circuit low | Wiring short to earth, SC bypass valve, ECM |
Wiring short to earth, TC wastegate regulating valve, | ||
P0249 | Turbocharger (TC) wastegate regulating valve B – circuit low | |
ECM | ||
Turbocharger (TC) intercooler bypass actuator A – | ||
P024A | Wiring, TC intercooler bypass actuator, ECM | |
range/performance problem | ||
Turbocharger (TC) intercooler bypass actuator A – actuator | ||
P024B | ||
stuck | ECM | |
Turbocharger (TC) intercooler bypass actuator position | ||
P024C | ||
sensor A – circuit malfunction | ECM | |
Charge air cooler bypass position sensor A – circuit | ||
P024D | Wiring, charge air cooler bypass position sensor, ECM | |
range/performance | ||
Turbocharger (TC) intercooler bypass actuator position | ||
P024E | ||
sensor A – circuit low | ECM | |
Turbocharger (TC) intercooler bypass actuator position | ||
P024F | ||
sensor A – circuit high | ECM | |
P0250 | Supercharger (SC) bypass valve B – circuit high | Wiring short to positive, SC bypass valve, ECM |
P0250 | Turbocharger (TC) wastegate regulating valve B – circuit high | |
ECM | ||
Injection pump fuel metering control A, cam/rotor/injector – | ||
P0251 | Wiring, injection pump, ECM | |
circuit malfunction | ||
Injection pump fuel metering control A, cam/rotor/injector – | ||
P0252 | Injection pump | |
range/performance problem | ||
Injection pump fuel metering control A, cam/rotor/injector – | ||
P0253 | Wiring short to earth, injection pump, ECM | |
circuit low | ||
Injection pump fuel metering control A, cam/rotor/injector – | ||
P0254 | Wiring short to positive, injection pump, ECM | |
circuit high | ||
Injection pump fuel metering control A, cam/rotor/injector – | ||
P0255 | Wiring, poor connection, injection pump, ECM | |
circuit intermittent | ||
Injection pump fuel metering control B, cam/rotor/injector – | ||
P0256 | Wiring, injection pump, ECM | |
circuit malfunction | ||
Injection pump fuel metering control B, cam/rotor/injector – | ||
P0257 | Injection pump | |
range/performance problem | ||
Injection pump fuel metering control B, cam/rotor/injector – | ||
P0258 | Wiring short to earth, injection pump, ECM | |
circuit low | ||
Injection pump fuel metering control B, cam/rotor/injector – | ||
P0259 | Wiring short to positive, injection pump, ECM | |
circuit high | ||
P025A | Fuel pump (FP) control module – open circuit | Wiring, FP control module, ECM |
P025B | Fuel pump (FP) control module – circuit range/performance | Wiring, FP control module, ECM |
P025C | Fuel pump (FP) control module – circuit low | Wiring, FP control module, ECM |
P025D | Fuel pump (FP) control module – circuit high | Wiring, FP control module, ECM |
Turbocharger (TC)/supercharger (SC) boost pressure sensor | ||
P025E | Wiring, TC/SC boost pressure sensor, ECM | |
A – intermittent/erratic signal | ||
Turbocharger (TC)/supercharger (SC) boost pressure sensor | ||
P025F | Wiring, TC/SC boost pressure sensor, ECM | |
B – intermittent/erratic signal | ||
Injection pump fuel metering control B, cam/rotor/injector – | ||
P0260 | Wiring, poor connection, injection pump, ECM | |
circuit intermittent | ||
P0261 | Injector 1 – circuit low | Wiring short to earth, injector, ECM |
P0262 | Injector 1 – circuit high | Wiring short to positive, injector, ECM |
P0263 | Cylinder 1 – contribution/balance fault | Wiring, fuel system, ECM |
P0264 | Injector 2 – circuit low | Wiring short to earth, injector, ECM |
P0265 | Injector 2 – circuit high | Wiring short to positive, injector, ECM |
P0266 | Cylinder 2 – contribution/balance fault | Wiring, fuel system, ECM |
P0267 | Injector 3 – circuit low | Wiring short to earth, injector, ECM |
P0268 | Injector 3 – circuit high | Wiring short to positive, injector, ECM |
P0269 | Cylinder 3 – contribution/balance fault | Wiring, fuel system, ECM |
P026A | Intercooler – efficiency below threshold | – |
P026B | Injection timing – performance problem | – |
Fuel level low, fuel leak/blockage, fuel pressure regulator, | ||
P026C | Fuel injection quantity – quantity lower than expected | |
fuel pump (FP), injector(s) | ||
fuel pipe blockage, fuel pressure relief valve, fuel | ||
P026D | Fuel injection quantity – quantity higher than expected | |
pressure regulator, fuel pump (FP), injector(s) | ||
P0270 | Injector 4 – circuit low | Wiring short to earth, injector, ECM |
P0271 | Injector 4 – circuit high | Wiring short to positive, injector, ECM |
P0272 | Cylinder 4 – contribution/balance fault | Wiring, fuel system, ECM |
P0273 | Injector 5 – circuit low | Wiring short to earth, injector, ECM |
P0274 | Injector 5 – circuit high | Wiring short to positive, injector, ECM |
P0275 | Cylinder 5 – contribution/balance fault | Wiring, fuel system, ECM |
P0276 | Injector 6 – circuit low | Wiring short to earth, injector, ECM |
P0277 | Injector 6 – circuit high | Wiring short to positive, injector, ECM |
P0278 | Cylinder 6 – contribution/balance fault | Wiring, fuel system, ECM |
P0279 | Injector 7 – circuit low | Wiring short to earth, injector, ECM |
P027A | Fuel pump control module B – open circuit | Wiring, FP control module, ECM |
P027B | Fuel pump control module B – circuit range/performance | Wiring, FP control module, ECM |
P027C | Fuel pump control module B – circuit low | Wiring, FP control module, ECM |
P027D | Fuel pump control module B – circuit high | Wiring, FP control module, ECM |
P0280 | Injector 7 – circuit high | Wiring short to positive, injector, ECM |
P0281 | Cylinder 7 – contribution/balance fault | Wiring, fuel system, ECM |
P0282 | Injector 8 – circuit low | Wiring short to earth, injector, ECM |
P0283 | Injector 8 – circuit high | Wiring short to positive, injector, ECM |
P0284 | Cylinder 8 – contribution/balance fault | Wiring, fuel system, ECM |
P0285 | Injector 9 – circuit low | Wiring short to earth, injector, ECM |
P0286 | Injector 9 – circuit high | Wiring short to positive, injector, ECM |
P0287 | Cylinder 9 – contribution/balance fault | Wiring, fuel system, ECM |
P0288 | Injector 10 – circuit low | Wiring short to earth, injector, ECM |
P0289 | Injector 10 – circuit high | Wiring short to positive, injector, ECM |
P0290 | Cylinder 10 – contribution/balance fault | Wiring, fuel system, ECM |
P0291 | Injector 11 – circuit low | Wiring short to earth, injector, ECM |
P0292 | Injector 11 – circuit high | Wiring short to positive, injector, ECM |
P0293 | Cylinder 11 – contribution/balance fault | Wiring, fuel system, ECM |
P0294 | Injector 12 – circuit low | Wiring short to earth, injector, ECM |
P0295 | Injector 12 – circuit high | Wiring short to positive, injector, ECM |
P0296 | Cylinder 12 – contribution/balance fault | Wiring, fuel system, ECM |
P0297 | Vehicle over-speed condition | Wiring, VSS, mechanical fault |
P0298 | Engine oil temperature too high | Wiring, EOT sensor, mechanical fault |
P0299 | Turbocharger (TC)/supercharger (SC) – low boost | Mechanical fault |
Injector, fuel pressure, MAF sensor, VAF sensor, MAP | ||
P029A | Fuel trim (FT), cylinder 1 – maximum control limit reached | |
sensor, ECM | ||
Injector, fuel pressure, MAF sensor, VAF sensor, MAP | ||
P029B | Fuel trim (FT), cylinder 1 – minimum control limit reached | |
sensor, ECM | ||
P029C | Injector 1 – blockage | Injector |
P029D | Injector 1 – leak | Injector |
Injector, fuel pressure, MAF sensor, VAF sensor, MAP | ||
P029E | Fuel trim (FT), cylinder 2 – maximum control limit reached | |
sensor, ECM | ||
Injector, fuel pressure, MAF sensor, VAF sensor, MAP | ||
P029F | Fuel trim (FT), cylinder 2 – minimum control limit reached | |
sensor, ECM | ||
P02A0 | Injector 2 – leak | Injector |
P02A1 | Injector 2 – leak | Injector |
Injector, fuel pressure, MAF sensor, VAF sensor, MAP | ||
P02A2 | Fuel trim (FT), cylinder 3 – maximum control limit reached | |
sensor, ECM | ||
Injector, fuel pressure, MAF sensor, VAF sensor, MAP | ||
P02A3 | Fuel trim (FT), cylinder 3 – minimum control limit reached | |
sensor, ECM | ||
P02A4 | Injector 3 – leak | Injector |
P02A5 | Injector 3 – leak | Injector |
Injector, fuel pressure, MAF sensor, VAF sensor, MAP | ||
P02A6 | Fuel trim (FT), cylinder 4 – maximum control limit reached | |
sensor, ECM | ||
Injector, fuel pressure, MAF sensor, VAF sensor, MAP | ||
P02A7 | Fuel trim (FT), cylinder 4 – minimum control limit reached | |
sensor, ECM | ||
P02A8 | Injector 4 – leak | Injector |
P02A9 | Injector 4 – leak | Injector |
Injector, fuel pressure, MAF sensor, VAF sensor, MAP | ||
P02AA | Fuel trim (FT), cylinder 5 – maximum control limit reached | |
sensor, ECM | ||
Injector, fuel pressure, MAF sensor, VAF sensor, MAP | ||
P02AB | Fuel trim (FT), cylinder 5 – minimum control limit reached | |
sensor, ECM | ||
P02AC | Cylinder 5 – injector leaking | Injector |
P02AD | Injector 5 – leak | Injector |
Injector, fuel pressure, MAF sensor, VAF sensor, MAP | ||
P02AE | Fuel trim (FT), cylinder 6 – maximum control limit reached | |
sensor, ECM | ||
Injector, fuel pressure, MAF sensor, VAF sensor, MAP | ||
P02AF | Fuel trim (FT), cylinder 6 – minimum control limit reached | |
sensor, ECM | ||
P02B0 | Injector 6 – leak | Injector |
P02B1 | Injector 6 – leak | Injector |
Injector, fuel pressure, MAF sensor, VAF sensor, MAP | ||
P02B2 | Fuel trim (FT), cylinder 7 – maximum control limit reached | |
sensor, ECM | ||
Injector, fuel pressure, MAF sensor, VAF sensor, MAP | ||
P02B3 | Fuel trim (FT), cylinder 7 – minimum control limit reached | |
sensor, ECM | ||
P02B4 | Injector 7 – leak | Injector |
P02B5 | Injector 7 – leak | Injector |
Injector, fuel pressure, MAF sensor, VAF sensor, MAP | ||
P02B6 | Fuel trim (FT), cylinder 8 – maximum control limit reached | |
sensor, ECM | ||
Injector, fuel pressure, MAF sensor, VAF sensor, MAP | ||
P02B7 | Fuel trim (FT), cylinder 8 – minimum control limit reached | |
sensor, ECM | ||
P02B8 | Injector 8 – leak | Injector |
P02B9 | Injector 8 – leak | Injector |
Injector, fuel pressure, MAF sensor, VAF sensor, MAP | ||
P02BA | Fuel trim (FT), cylinder 9 – maximum control limit reached | |
sensor, ECM | ||
P02BB | Injector 9 – offset learning at minimum limit | Wiring, injector, ECM |
P02BC | Injector 9 – leak | Injector |
P02BD | Injector 9 – leak | Injector |
Injector, fuel pressure, MAF sensor, VAF sensor, MAP | ||
P02BE | Fuel trim (FT), cylinder 10 – maximum control limit reached | |
sensor, ECM | ||
Injector, fuel pressure, MAF sensor, VAF sensor, MAP | ||
P02BF | Fuel trim (FT), cylinder 10 – minimum control limit reached | |
sensor, ECM | ||
P02C0 | Injector 10 – leak | Injector |
P02C1 | Injector 10 – leak | Injector |
Injector, fuel pressure, MAF sensor, VAF sensor, MAP | ||
P02C2 | Fuel trim (FT), cylinder 11 – maximum control limit reached | |
sensor, ECM | ||
Injector, fuel pressure, MAF sensor, VAF sensor, MAP | ||
P02C3 | Fuel trim (FT), cylinder 11 – minimum control limit reached | |
sensor, ECM | ||
P02C4 | Injector 11 – leak | Injector |
P02C5 | Injector 11 – leak | Injector |
Injector, fuel pressure, MAF sensor, VAF sensor, MAP | ||
P02C6 | Fuel trim (FT), cylinder 12 – maximum control limit reached | |
sensor, ECM | ||
Injector, fuel pressure, MAF sensor, VAF sensor, MAP | ||
P02C7 | Fuel trim (FT), cylinder 12 – minimum control limit reached | |
sensor, ECM | ||
P02C8 | Injector 12 – blockage | Injector |
P02C9 | Injector 12 – leak | Injector |
P02CA | Turbocharger (TC)/supercharger (SC) B – overboost condition | Wiring, TC wastegate actuator, SC control valve, ECM |
Wiring, MAP sensor, TC/SC boost pressure sensor, | ||
Turbocharger (TC)/supercharger (SC) B – underboost | ||
P02CB | turbocharger (TC) wastegate actuator, TC, SC, | |
condition | ||
mechanical fault, ECM | ||
P02CC | Injector 1 – offset learning at minimum limit | Wiring, injector, ECM |
P02CD | Injector 1 – offset learning at maximum limit | Wiring, injector, ECM |
P02CE | Injector 2 – offset learning at minimum limit | Wiring, injector, ECM |
P02CF | Injector 2 – offset learning at maximum limit | Wiring, injector, ECM |
P02D0 | Injector 3 – offset learning at minimum limit | Wiring, injector, ECM |
P02D1 | Injector 3 – offset learning at maximum limit | Wiring, injector, ECM |
P02D2 | Injector 4 – offset learning at minimum limit | Wiring, injector, ECM |
P02D3 | Injector 4 – offset learning at maximum limit | Wiring, injector, ECM |
P02D4 | Injector 5 – offset learning at minimum limit | Wiring, injector, ECM |
P02D5 | Injector 5 – offset learning at maximum limit | Wiring, injector, ECM |
P02D6 | Injector 6 – offset learning at minimum limit | Wiring, injector, ECM |
P02D7 | Injector 6 – offset learning at maximum limit | Wiring, injector, ECM |
P02D8 | Injector 7 – offset learning at minimum limit | Wiring, injector, ECM |
P02D9 | Injector 7 – offset learning at maximum limit | Wiring, injector, ECM |
P02DA | Injector 8 – offset learning at minimum limit | Wiring, injector, ECM |
P02DB | Injector 8 – offset learning at maximum limit | Wiring, injector, ECM |
P02DC | Injector 9 – offset learning at minimum limit | Wiring, injector, ECM |
P02DD | Injector 9 – offset learning at maximum limit | Wiring, injector, ECM |
P02DE | Injector 10 – offset learning at minimum limit | Wiring, injector, ECM |
P02DF | Injector 10 – offset learning at maximum limit | Wiring, injector, ECM |
P02E0 | Intake air flap control actuator – open circuit | Wiring, intake air flap control actuator, ECM |
Wiring, intake air flap control actuator, intake air flap | ||
P02E1 | Intake air flap control actuator – performance problem | |
control actuator position sensor, mechanical fault, ECM | ||
P02E2 | Intake air flap control actuator – circuit low | Wiring, intake air flap control actuator, ECM |
P02E3 | Intake air flap control actuator – circuit high | Wiring, intake air flap control actuator, ECM |
Wiring, intake air flap control actuator, intake air flap | ||
P02E4 | Intake air flap control actuator – actuator stuck open | |
control actuator position sensor, mechanical fault, ECM | ||
P02E5 | Intake air flap control actuator – actuator stuck closed | Intake air flap control actuator, mechanical fault |
Intake air flap control actuator position sensor – circuit | Wiring, intake air flap control actuator position sensor, | |
P02E6 | ||
malfunction | ECM | |
Intake air flap control actuator position sensor – | Wiring, intake air flap control actuator position sensor, | |
P02E7 | ||
range/performance | ECM | |
Wiring, intake air flap control actuator position sensor, | ||
P02E8 | Intake air flap control actuator position sensor – circuit low | |
ECM | ||
Wiring, intake air flap control actuator position sensor, | ||
P02E9 | Intake air flap control actuator position sensor – circuit high | |
ECM | ||
Intake air flap control actuator position sensor – circuit | Wiring, intake air flap control actuator position sensor, | |
P02EA | ||
intermittent/erratic | ECM | |
Diesel intake air flow control motor – current | ||
P02EB | Wiring, Diesel intake air flow control motor | |
range/performance | ||
P02EC | Diesel intake air flow control system – high air flow detected | Wiring, Diesel intake air flow control motor |
P02ED | Diesel intake air flow control system – low air flow detected | Wiring, Diesel intake air flow control motor |
P02EE | Injector 1 – circuit range/performance | Wiring, injector, ECM |
P02EF | Injector 2 – circuit range/performance | Wiring, injector, ECM |
P02F0 | Injector 3 – circuit range/performance | Wiring, injector, ECM |
P02F1 | Injector 4 – circuit range/performance | Wiring, injector, ECM |
P02F2 | Injector 5 – circuit range/performance | Wiring, injector, ECM |
P02F3 | Injector 6 – circuit range/performance | Wiring, injector, ECM |
P02F4 | Injector 7 – circuit range/performance | Wiring, injector, ECM |
P02F5 | Injector 8 – circuit range/performance | Wiring, injector, ECM |
P02F6 | Injector 9 – circuit range/performance | Wiring, injector, ECM |
P02F7 | Injector 10 – circuit range/performance | Wiring, injector, ECM |
P02F8 | Injector 11 – circuit range/performance | Wiring, injector, ECM |
P02F9 | Injector 12 – circuit range/performance | Wiring, injector, ECM |
Diesel intake air flow position sensor – minimum/maximum | ||
P02FA | Wiring, Diesel intake air flow position sensor | |
stop performance | ||
P0300 | Random/multiple cylinder(s) – misfire detected | |
compression, wiring | ||
Engine mechanical fault, wiring, ignition/fuel system, | ||
P0301 | Cylinder 1 – misfire detected | |
injector, ECT/MAF sensor, ECM | ||
Engine mechanical fault, wiring, ignition/fuel system, | ||
P0302 | Cylinder 2 – misfire detected | |
injector, ECT/MAF sensor, ECM | ||
Engine mechanical fault, wiring, ignition/fuel system, | ||
P0303 | Cylinder 3 – misfire detected | |
injector, ECT/MAF sensor, ECM | ||
Engine mechanical fault, wiring, ignition/fuel system, | ||
P0304 | Cylinder 4 – misfire detected | |
injector, ECT/MAF sensor, ECM | ||
Engine mechanical fault, wiring, ignition/fuel system, | ||
P0305 | Cylinder 5 – misfire detected | |
injector, ECT/MAF sensor, ECM | ||
Engine mechanical fault, wiring, ignition/fuel system, | ||
P0306 | Cylinder 6 – misfire detected | |
injector, ECT/MAF sensor, ECM | ||
Engine mechanical fault, wiring, ignition/fuel system, | ||
P0307 | Cylinder 7 – misfire detected | |
injector, ECT/MAF sensor, ECM | ||
Engine mechanical fault, wiring, ignition/fuel system, | ||
P0308 | Cylinder 8 – misfire detected | |
injector, ECT/MAF sensor, ECM | ||
Engine mechanical fault, wiring, ignition/fuel system, | ||
P0309 | Cylinder 9 – misfire detected | |
injector, ECT/MAF sensor, ECM | ||
Engine mechanical fault, wiring, ignition/fuel system, | ||
P0310 | Cylinder 10 – misfire detected | |
injector, ECT/MAF sensor, ECM | ||
Engine mechanical fault, wiring, ignition/fuel system, | ||
P0311 | Cylinder 11 – misfire detected | |
injector, ECT/MAF sensor, ECM | ||
Engine mechanical fault, wiring, ignition/fuel system, | ||
P0312 | Cylinder 12 – misfire detected | |
injector, ECT/MAF sensor, ECM | ||
P0313 | Misfire detected – low fuel level | Fuel system, mechanical fault |
Engine mechanical fault, wiring, ignition/fuel system, | ||
P0314 | Single cylinder misfire – cylinder not specified | |
injector | ||
P0315 | Crankshaft position system – variation not learned | Engine mechanical fault, wiring |
Engine mechanical fault, wiring, ignition/fuel system, | ||
P0316 | Misfire detected during start-up – first 1000 revolutions | |
injector | ||
P0317 | Rough road hardware not present | Wiring, ECM |
P0318 | Rough road sensor A – circuit malfunction | Wiring, rough road sensor A, mechanical fault |
P0319 | Rough road sensor B – circuit malfunction | Wiring, rough road sensor B, mechanical fault |
Crankshaft position (CKP) sensor/engine speed (RPM) | ||
P0320 | Wiring, CKP/RPM sensor, ECM | |
sensor – circuit malfunction | ||
Crankshaft position (CKP) sensor/engine speed (RPM) | Air gap, metal particle contamination, insecure | |
P0321 | ||
sensor – range/performance problem | sensor/rotor, wiring, CKP/RPM sensor | |
Crankshaft position (CKP) sensor/engine speed (RPM) | ||
P0322 | Wiring, CKP/RPM sensor, ECM | |
sensor – no signal | ||
Crankshaft position (CKP) sensor/engine speed (RPM) | ||
P0323 | Wiring, poor connection, CKP/RPM sensor, ECM | |
sensor – circuit intermittent | ||
P0324 | Knock control system error | Wiring, poor connection, KS, ECM |
P0325 | Knock sensor (KS) 1, bank 1 – circuit malfunction | Wiring, poor connection, KS |
P0326 | Knock sensor (KS) 1, bank 1 – range/performance problem | Wiring, KS incorrectly tightened, KS |
Insecure KS, poor connection, wiring short to earth, | ||
P0327 | Knock sensor (KS) 1, bank 1 – low input | |
incorrectly tightened, KS, ECM | ||
Wiring short to positive, KS incorrectly tightened, KS, | ||
P0328 | Knock sensor (KS) 1, bank 1 – high input | |
ECM | ||
P0329 | Knock sensor (KS) 1, bank 1 – circuit intermittent | Wiring, poor connection, KS, ECM |
P032A | Knock sensor (KS) 3, bank 1 – circuit malfunction | Wiring, KS, ECM |
P032B | Knock sensor (KS) 3, bank 1 – circuit range/performance | Wiring, KS, ECM |
P032C | Knock sensor (KS) 3, bank 1 – circuit low | Wiring, KS, ECM |
P032D | Knock sensor (KS) 3, bank 1 – circuit high | Wiring, KS, ECM |
P032E | Knock sensor (KS) 3, bank 1 – circuit intermittent | Wiring, KS, ECM |
P0330 | Knock sensor (KS) 2, bank 2 – circuit malfunction | Wiring, KS, ECM |
P0331 | Knock sensor (KS) 2, bank 2 – range/performance problem | Wiring, KS incorrectly tightened, KS |
Insecure KS, poor connection, wiring short to earth, KS | ||
P0332 | Knock sensor (KS) 2, bank 2 – low input | |
incorrectly tightened, KS, ECM | ||
Wiring short to positive, KS incorrectly tightened, KS, | ||
P0333 | Knock sensor (KS) 2, bank 2 – high input | |
ECM | ||
P0334 | Knock sensor (KS) 2, bank 2 – circuit intermittent | Wiring, poor connection, KS, ECM |
P0335 | Crankshaft position (CKP) sensor – circuit malfunction | Wiring, CKP sensor, ECM |
Crankshaft position (CKP) sensor – range/performance | ||
P0336 | Insecure sensor/rotor, air gap, wiring, CKP sensor | |
problem | ||
P0337 | Crankshaft position (CKP) sensor – low input | Wiring short to earth, CKP sensor, ECM |
P0338 | Crankshaft position (CKP) sensor – high input | Wiring short to positive, CKP sensor, ECM |
P0339 | Crankshaft position (CKP) sensor – circuit intermittent | Wiring, poor connection, CKP sensor, ECM |
P033A | Knock sensor (KS) 4, bank 2 – circuit malfunction | Wiring, KS, ECM |
P033B | Knock sensor (KS) 4, bank 2 – circuit range/performance | Wiring, KS, ECM |
P033C | Knock sensor (KS) 4, bank 2 – circuit low | Wiring, KS, ECM |
P033D | Knock sensor (KS) 4, bank 2 – circuit high | Wiring, KS, ECM |
P033E | Knock sensor (KS) 4, bank 2 – circuit intermittent | Wiring, KS, ECM |
Camshaft position (CMP) sensor A, bank 1 – circuit | ||
P0340 | Wiring, CMP sensor, ECM | |
malfunction | ||
Camshaft position (CMP) sensor A, bank 1 – | ||
P0341 | Insecure sensor/rotor, air gap, wiring, CMP sensor | |
range/performance problem | ||
P0342 | Camshaft position (CMP) sensor A, bank 1 – low input | Wiring short to earth, CMP sensor, ECM |
P0343 | Camshaft position (CMP) sensor A, bank 1 – high input | Wiring short to positive, CMP sensor, ECM |
Camshaft position (CMP) sensor A, bank 1 – circuit | ||
P0344 | Wiring, poor connection, CMP sensor, ECM | |
intermittent | ||
Camshaft position (CMP) sensor A, bank 2 – circuit | ||
P0345 | Wiring, CMP sensor, ECM | |
malfunction | ||
Camshaft position (CMP) sensor A, bank 2 – | ||
P0346 | Insecure sensor/rotor, air gap, wiring, CMP sensor | |
range/performance problem | ||
P0347 | Camshaft position (CMP) sensor A, bank 2 – low input | Wiring short to earth, CMP sensor, ECM |
P0348 | Camshaft position (CMP) sensor A, bank 2 – high input | Wiring short to positive, CMP sensor, ECM |
Camshaft position (CMP) sensor A, bank 2 – circuit | ||
P0349 | Wiring, poor connection, CMP sensor, ECM | |
intermittent | ||
P0350 | Ignition coil, primary/secondary – circuit malfunction | Wiring, ignition coil, ECM |
P0351 | Ignition coil A, primary/secondary – circuit malfunction | Wiring, ignition coil, ECM |
P0352 | Ignition coil B, primary/secondary – circuit malfunction | Wiring, ignition coil, ECM |
P0353 | Ignition coil C, primary/secondary – circuit malfunction | Wiring, ignition coil, ECM |
P0354 | Ignition coil D, primary/secondary – circuit malfunction | Wiring, ignition coil, ECM |
P0355 | Ignition coil E, primary/secondary – circuit malfunction | Wiring, ignition coil, ECM |
P0356 | Ignition coil F, primary/secondary – circuit malfunction | Wiring, ignition coil, ECM |
P0357 | Ignition coil G, primary/secondary – circuit malfunction | Wiring, ignition coil, ECM |
P0358 | Ignition coil H, primary/secondary – circuit malfunction | Wiring, ignition coil, ECM |
P0359 | Ignition coil I, primary/secondary – circuit malfunction | Wiring, ignition coil, ECM |
P0360 | Ignition coil J, primary/secondary – circuit malfunction | Wiring, ignition coil, ECM |
P0361 | Ignition coil K, primary/secondary – circuit malfunction | Wiring, ignition coil, ECM |
P0362 | Ignition coil L, primary/secondary – circuit malfunction | Wiring, ignition coil, ECM |
P0363 | Misfire detected – fuelling disabled | Fuel system, mechanical fault |
Camshaft position (CMP) sensor B, bank 1 – circuit | ||
P0365 | Wiring, poor connection, CMP sensor, ECM | |
malfunction | ||
Camshaft position (CMP) sensor B, bank 1 – circuit | ||
P0366 | Wiring, poor connection, CMP sensor | |
range/performance | ||
P0367 | Camshaft position (CMP) sensor B, bank 1 – circuit low input | Wiring short to earth, CMP sensor, ECM |
P0368 | Camshaft position (CMP) sensor B, bank 1 – circuit high input | Wiring short to positive, CMP sensor, ECM |
Camshaft position (CMP) sensor B, bank 1 – circuit | ||
P0369 | Wiring, poor connection, ECM | |
intermittent | ||
P0370 | Timing reference, high resolution signal A – malfunction | Wiring, CKP/RPM/CMP sensor, ECM |
P0371 | Timing reference, high resolution signal A – too many pulses | Wiring, CKP/RPM/CMP sensor, ECM |
P0372 | Timing reference, high resolution signal A – too few pulses | Wiring, CKP/RPM/CMP sensor, ECM |
Timing reference, high resolution signal A – intermittent/erratic | ||
P0373 | Wiring, poor connection, CKP/RPM/CMP sensor, ECM | |
pulses | ||
P0374 | Timing reference, high resolution signal A – no pulses | Wiring, CKP/RPM/CMP sensor, ECM |
P0375 | Timing reference, high resolution signal B – malfunction | Wiring, CKP/RPM/CMP sensor, ECM |
P0376 | Timing reference, high resolution signal B – too many pulses | Wiring, CKP/RPM/CMP sensor, ECM |
P0377 | Timing reference, high resolution signal B – too few pulses | Wiring, CKP/RPM/CMP sensor, ECM |
Timing reference, high resolution signal B – intermittent/erratic | ||
P0378 | Wiring, poor connection, CKP/RPM/CMP sensor, ECM | |
pulses | ||
P0379 | Timing reference, high resolution signal B – no pulses | Wiring, CKP/RPM/CMP sensor, ECM |
P037D | Glow plug monitoring – circuit malfunction | Wiring, glow plug control module, ECM |
P037E | Glow plug monitoring – circuit low | Wiring, glow plug control module, ECM |
P037F | Glow plug monitoring – circuit high | Wiring, glow plug control module, ECM |
P0380 | Glow plugs, circuit A – malfunction | Wiring, glow plug relay, fuse, glow plugs, ECM |
P0381 | Glow plug warning lamp – circuit malfunction | Wiring, glow plug warning lamp, ECM |
P0382 | Glow plugs, circuit B – malfunction | Wiring, glow plug relay, fuse, glow plugs, ECM |
P0383 | Glow plug control module – circuit low | Wiring short to earth, glow plug control module |
P0384 | Glow plug control module – circuit high | Wiring short to positive, glow plug control module |
P0385 | Crankshaft position (CKP) sensor B – circuit malfunction | Wiring, CKP sensor, ECM |
Crankshaft position (CKP) sensor B – range/performance | ||
P0386 | Insecure sensor/rotor, air gap, wiring, CKP sensor | |
problem | ||
P0387 | Crankshaft position (CKP) sensor B – low input | Wiring short to earth, CKP sensor, ECM |
P0388 | Crankshaft position (CKP) sensor B – high input | Wiring short to positive, CKP sensor, ECM |
P0389 | Crankshaft position (CKP) sensor B – circuit intermittent | Wiring, poor connection, CKP sensor, ECM |
Camshaft position (CMP) sensor B, bank 2 – circuit | ||
P0390 | Wiring, poor connection, CMP sensor, ECM | |
malfunction | ||
Camshaft position (CMP) sensor B, bank 2 – circuit | ||
P0391 | Wiring, poor connection, CMP sensor | |
range/performance | ||
P0392 | Camshaft position (CMP) sensor B, bank 2 – circuit low input | Wiring short to earth, CMP sensor, ECM |
P0393 | Camshaft position (CMP) sensor B, bank 2 – circuit high input | Wiring short to positive, CMP sensor, ECM |
Camshaft position (CMP) sensor B, bank 2 – circuit | ||
P0394 | Wiring, poor connection, ECM | |
intermittent | ||
P0395 | Cylinder pressure sensor, cylinder 1 – circuit malfunction | Wiring, cylinder pressure sensor, ECM |
Cylinder pressure sensor, cylinder 1 – circuit | ||
P0396 | Wiring, cylinder pressure sensor, ECM | |
range/performance | ||
P0397 | Cylinder pressure sensor, cylinder 1 – circuit low | Wiring, cylinder pressure sensor, ECM |
P0398 | Cylinder pressure sensor, cylinder 1 – circuit high | Wiring, cylinder pressure sensor, ECM |
Cylinder pressure sensor, cylinder 1 – circuit | ||
P0399 | Wiring, cylinder pressure sensor, ECM | |
intermittent/erratic | ||
P039A | Cylinder 1 – pressure too low | – |
P039B | Cylinder 1 – pressure too high | – |
P039C | Cylinder 1 – pressure variation low | – |
P039D | Cylinder 1 – pressure variation high | – |
P039E | Cylinder 1 – combustion performance | – |
P039F | Cylinder pressure sensor, cylinder 2 – circuit malfunction | Wiring, cylinder pressure sensor, ECM |
Cylinder pressure sensor, cylinder 2 – circuit | ||
P03A0 | Wiring, cylinder pressure sensor, ECM | |
range/performance | ||
P03A1 | Cylinder pressure sensor, cylinder 2 – circuit low | Wiring, cylinder pressure sensor, ECM |
P03A2 | Cylinder pressure sensor, cylinder 2 – circuit high | Wiring, cylinder pressure sensor, ECM |
Cylinder pressure sensor, cylinder 2 – circuit | ||
P03A3 | Wiring, cylinder pressure sensor, ECM | |
intermittent/erratic | ||
P03A4 | Cylinder 2 – pressure too low | – |
P03A5 | Cylinder 2 – pressure too high | – |
P03A6 | Cylinder 2 – pressure variation low | – |
P03A7 | Cylinder 2 – pressure variation high | – |
P03A8 | Cylinder 2 – combustion performance | – |
P03A9 | Cylinder pressure sensor, cylinder 3 – circuit malfunction | Wiring, cylinder pressure sensor, ECM |
Cylinder pressure sensor, cylinder 3 – circuit | ||
P03AA | Wiring, cylinder pressure sensor, ECM | |
range/performance | ||
P03AB | Cylinder pressure sensor, cylinder 3 – circuit low | Wiring, cylinder pressure sensor, ECM |
P03AC | Cylinder pressure sensor, cylinder 3 – circuit high | Wiring, cylinder pressure sensor, ECM |
Cylinder pressure sensor, cylinder 3 – circuit | ||
P03AD | Wiring, cylinder pressure sensor, ECM | |
intermittent/erratic | ||
P03AE | Cylinder 3 – pressure too low | – |
P03AF | Cylinder 3 – pressure too high | – |
P03B0 | Cylinder 3 – pressure variation low | – |
P03B1 | Cylinder 3 – pressure variation high | – |
P03B2 | Cylinder 3 – combustion performance | – |
P03B3 | Cylinder pressure sensor, cylinder 4 – circuit malfunction | Wiring, cylinder pressure sensor, ECM |
Cylinder pressure sensor, cylinder 4 – circuit | ||
P03B4 | Wiring, cylinder pressure sensor, ECM | |
range/performance | ||
P03B5 | Cylinder pressure sensor, cylinder 4 – circuit low | Wiring, cylinder pressure sensor, ECM |
P03B6 | Cylinder pressure sensor, cylinder 4 – circuit high | Wiring, cylinder pressure sensor, ECM |
Cylinder pressure sensor, cylinder 4 – circuit | ||
P03B7 | Wiring, cylinder pressure sensor, ECM | |
intermittent/erratic | ||
P03B8 | Cylinder 4 – pressure too low | – |
P03B9 | Cylinder 4 – pressure too high | – |
P03BA | Cylinder 4 – pressure variation low | – |
P03BB | Cylinder 4 – pressure variation high | – |
P03BC | Cylinder 4 – combustion performance | – |
P03BD | Cylinder pressure sensor, cylinder 5 – circuit malfunction | Wiring, cylinder pressure sensor, ECM |
Cylinder pressure sensor, cylinder 5 – circuit | ||
P03BE | Wiring, cylinder pressure sensor, ECM | |
range/performance | ||
P03BF | Cylinder pressure sensor, cylinder 5 – circuit low | Wiring, cylinder pressure sensor, ECM |
P03C0 | Cylinder pressure sensor, cylinder 5 – circuit high | Wiring, cylinder pressure sensor, ECM |
Cylinder pressure sensor, cylinder 5 – circuit | ||
P03C1 | Wiring, cylinder pressure sensor, ECM | |
intermittent/erratic | ||
P03C2 | Cylinder 5 – pressure too low | – |
P03C3 | Cylinder 5 – pressure too high | – |
P03C4 | Cylinder 5 – pressure variation low | – |
P03C5 | Cylinder 5 – pressure variation high | – |
P03C6 | Cylinder 5 – combustion performance | – |
P03C7 | Cylinder pressure sensor, cylinder 6 – circuit malfunction | Wiring, cylinder pressure sensor, ECM |
Cylinder pressure sensor, cylinder 6 – circuit | ||
P03C8 | Wiring, cylinder pressure sensor, ECM | |
range/performance | ||
P03C9 | Cylinder pressure sensor, cylinder 6 – circuit low | Wiring, cylinder pressure sensor, ECM |
P03CA | Cylinder pressure sensor, cylinder 6 – circuit high | Wiring, cylinder pressure sensor, ECM |
Cylinder pressure sensor, cylinder 6 – circuit | ||
P03CB | Wiring, cylinder pressure sensor, ECM | |
intermittent/erratic | ||
P03CC | Cylinder 6 – pressure too low | – |
P03CD | Cylinder 6 – pressure too high | – |
P03CE | Cylinder 6 – pressure variation low | – |
P03CF | Cylinder 6 – pressure variation high | – |
P03D0 | Cylinder 6 – combustion performance | – |
P03D1 | Cylinder pressure sensor, cylinder 7 – circuit malfunction | Wiring, cylinder pressure sensor, ECM |
Cylinder pressure sensor, cylinder 7 – circuit | ||
P03D2 | Wiring, cylinder pressure sensor, ECM | |
range/performance | ||
P03D3 | Cylinder pressure sensor, cylinder 7 – circuit low | Wiring, cylinder pressure sensor, ECM |
P03D4 | Cylinder pressure sensor, cylinder 7 – circuit high | Wiring, cylinder pressure sensor, ECM |
Cylinder pressure sensor, cylinder 7 – circuit | ||
P03D5 | Wiring, cylinder pressure sensor, ECM | |
intermittent/erratic | ||
P03D6 | Cylinder 7 – pressure too low | – |
P03D7 | Cylinder 7 – pressure too high | – |
P03D8 | Cylinder 7 – pressure variation low | – |
P03D9 | Cylinder 7 – pressure variation high | – |
P03DA | Cylinder 7 – combustion performance | – |
P03DB | Cylinder pressure sensor, cylinder 8 – circuit malfunction | Wiring, cylinder pressure sensor, ECM |
Cylinder pressure sensor, cylinder 8 – circuit | ||
P03DC | Wiring, cylinder pressure sensor, ECM | |
range/performance | ||
P03DD | Cylinder pressure sensor, cylinder 8 – circuit low | Wiring, cylinder pressure sensor, ECM |
P03DE | Cylinder pressure sensor, cylinder 8 – circuit high | Wiring, cylinder pressure sensor, ECM |
Cylinder pressure sensor, cylinder 8 – circuit | ||
P03DF | Wiring, cylinder pressure sensor, ECM | |
intermittent/erratic | ||
P03E0 | Cylinder 8 – pressure too low | – |
P03E1 | Cylinder 8 – pressure too high | – |
P03E2 | Cylinder 8 – pressure variation low | – |
P03E3 | Cylinder 8 – pressure variation high | – |
P03E4 | Cylinder 8 – combustion performance | – |
Hose leak/blockage, basic setting not carried out (if | ||
P0400 | Exhaust gas recirculation (EGR) system – flow malfunction | |
applicable), wiring, EGR valve, EGR solenoid, ECM | ||
Exhaust gas recirculation (EGR) system – insufficient flow | Hose leak/blockage, basic setting not carried out (if | |
P0401 | ||
detected | applicable), wiring, EGR valve, EGR solenoid, ECM | |
Exhaust gas recirculation (EGR) system – excessive flow | Hose leak/blockage, basic setting not carried out (if | |
P0402 | ||
detected | applicable), wiring, EGR valve, EGR solenoid, ECM | |
P0403 | Exhaust gas recirculation (EGR) – circuit malfunction | Wiring, EGR solenoid, ECM |
Exhaust gas recirculation (EGR) system – range/performance | ||
P0404 | Hose leak/blockage, wiring, EGR valve/solenoid | |
problem | ||
Exhaust gas recirculation (EGR) valve position sensor A – low | ||
P0405 | Wiring short to earth, EGR valve position sensor, ECM | |
input | ||
Exhaust gas recirculation (EGR) valve position sensor A – | ||
P0406 | Wiring short to positive, EGR valve position sensor, ECM | |
high input | ||
Exhaust gas recirculation (EGR) valve position sensor B – low | ||
P0407 | Wiring short to earth, EGR valve position sensor, ECM | |
input | ||
Exhaust gas recirculation (EGR) valve position sensor B – | ||
P0408 | Wiring short to positive, EGR valve position sensor, ECM | |
high input | ||
Exhaust gas recirculation (EGR) sensor A – circuit | ||
P0409 | Wiring, poor connection, EGR sensor, ECM | |
malfunction | ||
Exhaust gas recirculation (EGR) temperature sensor A – | ||
P040A | Wiring, EGR temperature sensor, ECM | |
circuit malfunction | ||
Exhaust gas recirculation (EGR) temperature sensor A – | ||
P040B | Wiring, EGR temperature sensor, ECM | |
circuit range/performance | ||
Exhaust gas recirculation (EGR) temperature sensor A – | ||
P040C | Wiring, EGR temperature sensor, ECM | |
circuit low | ||
Exhaust gas recirculation (EGR) temperature sensor A – | ||
P040D | Wiring, EGR temperature sensor, ECM | |
circuit high | ||
Exhaust gas recirculation (EGR) temperature sensor A – | ||
P040E | Wiring, EGR temperature sensor, ECM | |
circuit intermittent/erratic | ||
Exhaust gas recirculation (EGR) temperature sensor A/B – | ||
P040F | Wiring, EGR temperature sensor, ECM | |
correlation | ||
P0410 | Secondary air injection (AIR) system – malfunction | Wiring, AIR valve, AIR solenoid, ECM |
P0411 | Secondary air injection (AIR) system – incorrect flow detected | AIR pump, AIR valve, AIR hose(s) |
P0412 | Secondary air injection (AIR) solenoid A – circuit malfunction | Wiring, AIR solenoid, ECM |
P0413 | Secondary air injection (AIR) solenoid A – open circuit | Wiring open circuit, AIR solenoid, ECM |
P0414 | Secondary air injection (AIR) solenoid A – short circuit | Wiring short circuit, AIR solenoid, ECM |
P0415 | Secondary air injection (AIR) solenoid B – circuit malfunction | Wiring, AIR solenoid, ECM |
P0416 | Secondary air injection (AIR) solenoid B – open circuit | Wiring open circuit, AIR solenoid, ECM |
P0417 | Secondary air injection (AIR) solenoid B – short circuit | Wiring short circuit, AIR solenoid, ECM |
Secondary air injection (AIR) pump relay A – circuit | ||
P0418 | Wiring, AIR pump relay, ECM | |
malfunction | ||
Secondary air injection (AIR) pump relay B – circuit | ||
P0419 | Wiring, AIR pump relay, ECM | |
malfunction | ||
Exhaust gas recirculation (EGR) temperature sensor B – | ||
P041A | Wiring, EGR temperature sensor, ECM | |
circuit malfunction | ||
Exhaust gas recirculation (EGR) temperature sensor B – | ||
P041B | Wiring, EGR temperature sensor, ECM | |
circuit range/performance | ||
Exhaust gas recirculation (EGR) temperature sensor B – | ||
P041C | Wiring, EGR temperature sensor, ECM | |
circuit low | ||
Exhaust gas recirculation (EGR) temperature sensor B – | ||
P041D | Wiring, EGR temperature sensor, ECM | |
circuit high | ||
Exhaust gas recirculation (EGR) temperature sensor B – | ||
P041E | Wiring, EGR temperature sensor, ECM | |
circuit intermittent/erratic | ||
P041F | Secondary air injection (AIR) switching valve A – circuit low | Wiring, AIR switching valve, ECM |
Catalytic converter system, bank 1 – efficiency below | ||
P0420 | Catalytic converter, wiring, HO2S 2 | |
threshold | ||
Warm up catalytic converter, bank 1 – efficiency below | ||
P0421 | Catalytic converter, wiring, HO2S 2 | |
threshold | ||
P0422 | Main catalytic converter, bank 1 – efficiency below threshold | Catalytic converter, wiring, HO2S 2 |
Heated catalytic converter, bank 1 – efficiency below | ||
P0423 | Catalytic converter, wiring, HO2S 2 | |
threshold | ||
Heated catalytic converter, bank 1 – temperature below | ||
P0424 | Catalytic converter, wiring, HO2S 2 | |
threshold | ||
Wiring, poor connection, catalytic converter temperature | ||
P0425 | Catalytic converter temperature sensor, bank 1 | |
sensor, ECM | ||
Catalytic converter temperature sensor, bank 1 – | Wiring, poor connection, catalytic converter temperature | |
P0426 | ||
range/performance problem | sensor | |
Wiring short to earth, catalytic converter temperature | ||
P0427 | Catalytic converter temperature sensor, bank 1 – low input | |
sensor, ECM | ||
Wiring short to positive, catalytic converter temperature | ||
P0428 | Catalytic converter temperature sensor, bank 1 – high input | |
sensor, ECM | ||
P0429 | Catalytic converter heater, bank 1 – circuit malfunction | Wiring, relay, ECM |
Catalytic converter temperature sensor 2, bank 1 – circuit | ||
P042A | Wiring, catalytic converter temperature sensor, ECM | |
malfunction | ||
Catalytic converter temperature sensor 2, bank 1 – circuit | ||
P042B | Wiring, catalytic converter temperature sensor, ECM | |
range/performance | ||
P042C | Catalytic converter temperature sensor 2, bank 1 – circuit low | Wiring, catalytic converter temperature sensor, ECM |
P042D | Catalytic converter temperature sensor 2, bank 1 – circuit high | Wiring, catalytic converter temperature sensor, ECM |
Exhaust gas recirculation (EGR) valve actuator A – actuator | ||
P042E | Wiring, EGR valve actuator, mechanical fault, ECM | |
stuck open | ||
Exhaust gas recirculation (EGR) valve actuator A – actuator | ||
P042F | Wiring, EGR valve actuator, mechanical fault, ECM | |
stuck closed | ||
Catalytic converter system, bank 2 – efficiency below | ||
P0430 | Catalytic converter, wiring, HO2S 2 | |
threshold | ||
Warm up catalytic converter, bank 2 – efficiency below | ||
P0431 | Catalytic converter, wiring, HO2S 2 | |
threshold | ||
P0432 | Main catalytic converter, bank 2 – efficiency below threshold | Catalytic converter, wiring, HO2S 2 |
Heated catalytic converter, bank 2 – efficiency below | ||
P0433 | Catalytic converter, wiring, HO2S 2 | |
threshold | ||
Heated catalytic converter, bank 2 – temperature below | ||
P0434 | Catalytic converter, wiring, HO2S 2 | |
threshold | ||
Wiring, poor connection, catalytic converter temperature | ||
P0435 | Catalytic converter temperature sensor, bank 2 | |
sensor, ECM | ||
Catalytic converter temperature sensor, bank 2 – | Wiring, poor connection, catalytic converter temperature | |
P0436 | ||
range/performance problem | sensor | |
Wiring short to earth, catalytic converter temperature | ||
P0437 | Catalytic converter temperature sensor, bank 2 – low input | |
sensor, ECM | ||
Wiring short to positive, catalytic converter temperature | ||
P0438 | Catalytic converter temperature sensor, bank 2 – high input | |
sensor, ECM | ||
P0439 | Catalytic converter heater, bank 2 – circuit malfunction | Wiring, relay, ECM |
Catalytic converter temperature sensor 2, bank 2 – circuit | ||
P043A | Wiring, catalytic converter temperature sensor, ECM | |
malfunction | ||
Catalytic converter temperature sensor 2, bank 2 – circuit | ||
P043B | Wiring, catalytic converter temperature sensor, ECM | |
range/performance | ||
P043C | Catalytic converter temperature sensor 2, bank 2 – circuit low | Wiring, catalytic converter temperature sensor, ECM |
P043D | Catalytic converter temperature sensor 2, bank 2 – circuit high | Wiring, catalytic converter temperature sensor, ECM |
Evaporative emission (EVAP) leak detection reference orifice | Wiring, EVAP leak detection control module, hose | |
P043E | ||
– low flow | connections, ECM | |
Evaporative emission (EVAP) leak detection system | Wiring, EVAP leak detection control module, hose | |
P043F | ||
reference orifice – excessive flow detected | connections, ECM | |
Hose connection(s), intake leak, EVAP canister purge | ||
P0440 | Evaporative emission (EVAP) system – malfunction | |
valve | ||
Evaporative emission (EVAP) system – incorrect flow | Hose connection(s), intake leak, EVAP canister purge | |
P0441 | ||
detected | valve | |
Hose connection(s), intake leak, EVAP canister, EVAP | ||
P0442 | Evaporative emission (EVAP) system – small leak detected | |
canister purge valve | ||
Evaporative emission (EVAP) canister purge valve – circuit | ||
P0443 | Wiring, EVAP canister purge valve, ECM | |
malfunction | ||
Evaporative emission (EVAP) canister purge valve – open | ||
P0444 | Wiring open circuit, EVAP canister purge valve, ECM | |
circuit | ||
Evaporative emission (EVAP) canister purge valve – short | ||
P0445 | Wiring short circuit, EVAP canister purge valve, ECM | |
circuit | ||
Evaporative emission (EVAP) system, vent control – circuit | ||
P0446 | Wiring, EVAP canister purge valve, ECM | |
malfunction | ||
Evaporative emission (EVAP) system, vent control – open | ||
P0447 | Wiring open circuit, EVAP canister purge valve, ECM | |
circuit | ||
Evaporative emission (EVAP) system, vent control – short | ||
P0448 | Wiring short circuit, EVAP canister purge valve, ECM | |
circuit | ||
Evaporative emission (EVAP) system, vent valve – circuit | ||
P0449 | Wiring, EVAP canister purge valve, ECM | |
malfunction | ||
Exhaust gas recirculation (EGR) sensor C – circuit | ||
P044A | Wiring, EGR sensor, ECM | |
malfunction | ||
Exhaust gas recirculation (EGR) sensor C – | ||
P044B | Wiring, EGR sensor, ECM | |
range/performance problem | ||
Exhaust gas recirculation (EGR) valve position sensor C – | ||
P044C | Wiring, EGR valve position sensor, ECM | |
circuit low | ||
P044D | Exhaust gas recirculation (EGR) sensor C – circuit high | Wiring, EGR sensor, ECM |
Exhaust gas recirculation (EGR) sensor C – circuit | ||
P044E | Wiring, EGR sensor, ECM | |
intermittent/erratic | ||
P044F | Secondary air injection (AIR) switching valve A – circuit high | Wiring, AIR switching valve, ECM |
Evaporative emission (EVAP) pressure sensor – circuit | ||
P0450 | Wiring, EVAP pressure sensor, ECM | |
malfunction | ||
Evaporative emission (EVAP) pressure sensor – | ||
P0451 | EVAP pressure sensor | |
range/performance problem | ||
P0452 | Evaporative emission (EVAP) pressure sensor – low input | Wiring short to earth, EVAP pressure sensor, ECM |
P0453 | Evaporative emission (EVAP) pressure sensor – high input | Wiring short to positive, EVAP pressure sensor, ECM |
Evaporative emission (EVAP) pressure sensor – circuit | ||
P0454 | Wiring, poor connection, EVAP pressure sensor, ECM | |
intermittent | ||
Hose connection(s), intake leak, EVAP canister, EVAP | ||
P0455 | Evaporative emission (EVAP) system – large leak detected | |
canister purge valve | ||
Evaporative emission (EVAP) system – very small leak | Mechanical fault, hose connection(s), EVAP pressure | |
P0456 | ||
detected | sensor | |
Evaporative emission (EVAP) system – leak detected (filler | Mechanical fault, hose connection(s), EVAP pressure | |
P0457 | ||
cap loose/off) | sensor | |
Evaporative emission (EVAP) system, EVAP valve – circuit | ||
P0458 | Wiring short to earth, EVAP valve | |
low | ||
Evaporative emission (EVAP) system, EVAP valve – circuit | ||
P0459 | Wiring short to positive, EVAP valve | |
high | ||
Exhaust gas recirculation (EGR) valve actuator B – circuit | ||
P045A | Wiring, EGR valve actuator, ECM | |
malfunction | ||
Exhaust gas recirculation (EGR) valve B – circuit | ||
P045B | Wiring, EGR valve, ECM | |
range/performance | ||
P045C | Exhaust gas recirculation (EGR) valve actuator B – circuit low | Wiring, EGR valve actuator, ECM |
Exhaust gas recirculation (EGR) valve actuator B – circuit | ||
P045D | Wiring, EGR valve actuator, ECM | |
high | ||
Exhaust gas recirculation (EGR) valve actuator B – actuator | ||
P045E | Wiring, EGR valve actuator, mechanical fault, ECM | |
stuck open | ||
P045F | Exhaust gas recirculation (EGR) valve B – valve stuck closed | Wiring, EGR valve, mechanical fault, ECM |
P0460 | Fuel tank level sensor – circuit malfunction | Wiring, fuel tank level sensor, ECM |
P0461 | Fuel tank level sensor – range/performance problem | Wiring, fuel tank level sensor |
P0462 | Fuel tank level sensor – low input | Wiring short to earth, fuel tank level sensor, ECM |
P0463 | Fuel tank level sensor – high input | Wiring short to positive, fuel tank level sensor, ECM |
P0464 | Fuel tank level sensor – circuit intermittent | Wiring, poor connection, fuel tank level sensor, ECM |
Evaporative emission (EVAP) canister purge flow sensor – | ||
P0465 | Wiring, EVAP canister purge flow sensor, ECM | |
circuit malfunction | ||
Evaporative emission (EVAP) canister purge flow sensor – | ||
P0466 | EVAP canister purge flow sensor | |
range/performance problem | ||
Evaporative emission (EVAP) canister purge flow sensor – | Wiring short to earth, EVAP canister purge flow sensor, | |
P0467 | ||
low input | ECM | |
Evaporative emission (EVAP) canister purge flow sensor – | Wiring short to positive, EVAP canister purge flow | |
P0468 | ||
high input | sensor, ECM | |
Evaporative emission (EVAP) canister purge flow sensor – | Wiring, poor connection, EVAP canister purge flow | |
P0469 | ||
circuit intermittent | sensor, ECM | |
Catalytic converter temperature sensor 1/2, bank 1 – | ||
P046A | Wiring, catalytic converter temperature sensor, ECM | |
correlation | ||
Catalytic converter temperature sensor 1/2, bank 2 – | ||
P046B | Wiring, catalytic converter temperature sensor, ECM | |
correlation | ||
Exhaust gas recirculation (EGR) valve position sensor A – | ||
P046C | Wiring, EGR valve position sensor, ECM | |
range/performance problem | ||
Exhaust gas recirculation (EGR) sensor A – | ||
P046D | Wiring, EGR sensor, ECM | |
intermittent/erratic | ||
Exhaust gas recirculation (EGR) sensor B – | ||
P046E | Wiring, EGR sensor, ECM | |
range/performance problem | ||
Exhaust gas recirculation (EGR) sensor B – | ||
P046F | Wiring, EGR sensor, ECM | |
intermittent/erratic | ||
P0470 | Exhaust gas pressure sensor – circuit malfunction | Wiring, exhaust gas pressure sensor, ECM |
P0471 | Exhaust gas pressure sensor – range/performance problem | Exhaust gas pressure sensor |
P0472 | Exhaust gas pressure sensor – low input | Wiring short to earth, exhaust gas pressure sensor, ECM |
Wiring short to positive, exhaust gas pressure sensor, | ||
P0473 | Exhaust gas pressure sensor – high input | |
ECM | ||
Wiring, poor connection, exhaust gas pressure sensor, | ||
P0474 | Exhaust gas pressure sensor – circuit intermittent | |
ECM | ||
P0475 | Exhaust gas pressure control valve – circuit malfunction | Wiring, exhaust gas pressure control valve, ECM |
Exhaust gas pressure control valve – range/performance | ||
P0476 | Exhaust gas pressure control valve | |
problem | ||
Wiring short to earth, exhaust gas pressure control valve, | ||
P0477 | Exhaust gas pressure control valve – low input | |
ECM | ||
Wiring short to positive, exhaust gas pressure control | ||
P0478 | Exhaust gas pressure control valve – high input | |
valve, ECM | ||
Wiring, poor connection, exhaust gas pressure control | ||
P0479 | Exhaust gas pressure control valve – circuit intermittent | |
valve, ECM | ||
P047A | Exhaust gas pressure sensor B – circuit | Wiring, exhaust gas pressure sensor, ECM |
P047B | Exhaust gas pressure sensor B – circuit range/performance | Wiring, exhaust gas pressure sensor, ECM |
P047C | Exhaust gas pressure sensor B – circuit low | Wiring, exhaust gas pressure sensor, ECM |
P047D | Exhaust gas pressure sensor B – circuit high | Wiring, exhaust gas pressure sensor, ECM |
P047E | Exhaust gas pressure sensor B – circuit intermittent/erratic | Wiring, exhaust gas pressure sensor, ECM |
Wiring, exhaust gas pressure control valve, mechanical | ||
P047F | Exhaust gas pressure control valve – valve stuck open | |
fault, ECM | ||
P0480 | Engine coolant blower motor 1 – circuit malfunction | Wiring, engine coolant blower motor, ECM |
P0481 | Engine coolant blower motor 2 – circuit malfunction | Wiring, engine coolant blower motor, ECM |
P0482 | Engine coolant blower motor 3 – circuit malfunction | Wiring, engine coolant blower motor, ECM |
P0483 | Engine coolant blower motor, rationality check – malfunction | Wiring, engine coolant blower motor, ECM |
P0484 | Engine coolant blower motor – circuit over current | Wiring, engine coolant blower motor, ECM |
P0485 | Engine coolant blower motor, power/earth – circuit malfunction | Wiring, engine coolant blower motor, ECM |
Exhaust gas recirculation (EGR) valve position sensor B – | Wiring, poor connection, EGR valve position sensor, | |
P0486 | ||
circuit malfunction | ECM | |
Exhaust gas recirculation (EGR) system, throttle position | ||
P0487 | Wiring, poor connection, ECM | |
control – circuit malfunction | ||
Exhaust gas recirculation (EGR) system, throttle position | ||
P0488 | Wiring, poor connection, ECM | |
control – range/performance problem | ||
P0489 | Exhaust gas recirculation (EGR) system – circuit low | Wiring short to earth, EGR valve |
Wiring, exhaust gas control actuator, mechanical fault, | ||
P048A | Exhaust gas control actuator – actuator stuck closed | |
ECM | ||
Exhaust gas control actuator position sensor/switch – circuit | Wiring, exhaust gas control actuator position sensor, | |
P048B | ||
malfunction | ECM | |
Exhaust gas control actuator position sensor/switch – circuit | Wiring, exhaust gas control actuator position sensor, | |
P048C | ||
range/performance | ECM | |
Exhaust gas pressure control valve position sensor/switch – | Wiring, exhaust gas pressure control valve position | |
P048D | ||
circuit low | sensor/switch, ECM | |
Exhaust gas pressure control valve position sensor/switch – | Wiring, exhaust gas pressure control valve position | |
P048E | ||
circuit high | sensor, ECM | |
Exhaust gas control actuator position sensor/switch – circuit | Wiring, exhaust gas control actuator position | |
P048F | ||
intermittent/erratic | sensor/switch, ECM | |
P0490 | Exhaust gas recirculation (EGR) system – circuit high | Wiring short to positive, EGR valve |
P0491 | Secondary air injection (AIR) system, bank 1 – malfunction | Wiring, AIR solenoid, hose connections, mechanical fault |
P0492 | Secondary air injection (AIR) system, bank 2 – malfunction | Wiring, AIR solenoid, hose connections, mechanical fault |
P0493 | Engine coolant blower motor over-speed (clutch locked) | Blower motor clutch, mechanical fault |
P0494 | Engine coolant blower motor speed – low | Wiring, relay, blower motor, mechanical fault |
P0495 | Engine coolant blower motor speed – high | Wiring, relay, blower motor, mechanical fault |
P0496 | Evaporative emission (EVAP) system – high purge flow | Wiring, EVAP valve, mechanical fault |
P0497 | Evaporative emission (EVAP) system – low purge flow | |
Evaporative emission (EVAP) system, vent control – circuit | ||
P0498 | Wiring short to earth, EVAP valve | |
low | ||
Evaporative emission (EVAP) system, vent control – circuit | ||
P0499 | Wiring short to positive, EVAP valve | |
high | ||
Exhaust gas recirculation (EGR) valve actuator B – flow | ||
P049A | Wiring, EGR valve actuator, ECM | |
malfunction | ||
P049B | Exhaust gas recirculation (EGR) B – insufficient flow detected | |
sensor, MAP sensor, VAF sensor, ECM | ||
Exhaust gas recirculation (EGR) valve actuator B – excessive | ||
P049C | Wiring, EGR valve actuator, ECM | |
flow detected | ||
Exhaust gas recirculation (EGR) valve actuator A – learning | ||
P049D | Wiring, EGR valve actuator, ECM | |
limit exceeded | ||
Exhaust gas recirculation (EGR) valve B – learning limit | ||
P049E | Wiring, EGR valve, ECM | |
exceeded | ||
P049F | Exhaust gas pressure control valve B | – |
Exhaust gas pressure control valve B – circuit | ||
P04A0 | – | |
range/performance | ||
P04A1 | Exhaust gas pressure control valve B – circuit low | – |
P04A2 | Exhaust gas pressure control valve B – circuit high | – |
P04A3 | Exhaust gas pressure control valve B – circuit intermittent | – |
P04A4 | Exhaust gas pressure control valve B – valve stuck open | – |
P04A5 | Exhaust gas pressure control valve B – valve stuck closed | – |
Exhaust gas pressure control valve position sensor/switch B – | ||
P04A6 | – | |
circuit malfunction | ||
Exhaust gas pressure control valve position sensor/switch B – | ||
P04A7 | – | |
circuit range/performance | ||
Exhaust gas pressure control valve position sensor/switch B – | ||
P04A8 | – | |
circuit low | ||
Exhaust gas pressure control valve position sensor/switch B – | ||
P04A9 | – | |
circuit high | ||
Exhaust gas pressure control valve position sensor/switch B – | ||
P04AA | – | |
circuit intermittent/erratic | ||
Evaporative emission (EVAP) canister purge valve B – open | ||
P04AB | ||
circuit | ||
Evaporative emission (EVAP) canister purge valve B – circuit | ||
P04AC | ||
low | ||
Evaporative emission (EVAP) canister purge valve B – circuit | ||
P04AD | ||
high | ||
Evaporative emission (EVAP) canister purge valve B – | ||
P04AE | ||
performance problem or valve stuck open | ||
Evaporative emission (EVAP) canister purge valve B – EVAP | ||
P04AF | ||
valve stuck closed | ||
P04B0 | Refuelling vapour control valve – open circuit | Wiring, refuelling vapour control valve |
P04B1 | Refuelling vapour control valve – circuit low | Wiring, refuelling vapour control valve |
P04B2 | Refuelling vapour control valve – circuit high | Wiring, refuelling vapour control valve |
Refuelling vapour control valve – performance problem or | ||
P04B3 | Wiring, refuelling vapour control valve | |
valve stuck open | ||
P04B4 | Refuelling vapour control valve – valve stuck closed | Wiring, refuelling vapour control valve |
P04B5 | Fuel filler flap – flap stuck open | – |
P04B6 | Fuel filler flap – flap stuck closed | – |
P04B7 | Fuel filler flap sensor/switch – circuit intermittent/erratic | Wiring, fuel filler flap sensor/switch |
P04B8 | Fuel filler flap sensor/switch – circuit malfunction | Wiring, fuel filler flap sensor/switch |
P04B9 | Fuel filler flap sensor/switch – circuit low | Wiring, fuel filler flap sensor/switch |
P04BA | Fuel filler flap sensor/switch – circuit high | Wiring, fuel filler flap sensor/switch |
P04BB | Fuel filler flap lock control – circuit open | Wiring, fuel filler flap actuator |
P04BC | Fuel filler flap lock control – circuit range/performance | Wiring, fuel filler flap actuator |
P04BD | Fuel filler flap lock control – circuit low | Wiring, fuel filler flap actuator |
P04BE | Fuel filler flap lock control – circuit high | Wiring, fuel filler flap actuator |
P04BF | Fuel filler flap unlock control – circuit open | Wiring, fuel filler flap actuator |
P04C0 | Fuel filler flap unlock control – circuit range/performance | Wiring, fuel filler flap actuator |
P04C1 | Fuel filler flap unlock control – circuit low | Wiring, fuel filler flap actuator |
P04C2 | Fuel filler flap unlock control – circuit high | Wiring, fuel filler flap actuator |
P04C3 | Fuel filler flap lock position sensor/switch – circuit malfunction | Wiring, fuel filler flap lock position sensor/switch |
Fuel filler flap lock position sensor/switch – circuit | ||
P04C4 | Wiring, fuel filler flap lock position sensor/switch | |
range/performance | ||
P04C5 | Fuel filler flap lock position sensor/switch – circuit low | Wiring, fuel filler flap lock position sensor/switch |
P04C6 | Fuel filler flap lock position sensor/switch – circuit high | Wiring, fuel filler flap lock position sensor/switch |
Fuel filler flap lock position sensor/switch – circuit | ||
P04C7 | Wiring, fuel filler flap lock position sensor/switch | |
intermittent/erratic | ||
P04C8 | Fuel filler flap open request sensor/switch – circuit malfunction | Wiring, fuel filler flap open request sensor/switch |
Fuel filler flap open request sensor/switch – performance or | ||
P04C9 | Wiring, fuel filler flap open request sensor/switch | |
stuck off | ||
P04CA | Fuel filler flap open request sensor/switch – signal stuck low | Wiring, fuel filler flap open request sensor/switch |
P04CB | Fuel filler flap open request sensor/switch – signal stuck high | Wiring, fuel filler flap open request sensor/switch |
Fuel filler flap open request sensor/switch – intermittent/erratic | ||
P04CC | Wiring, fuel filler flap open request sensor/switch | |
signal | ||
P04CD | Fuel filler flap open request sensor/switch – stuck on | Wiring, fuel filler flap open request sensor/switch |
Exhaust gas recirculation (EGR) temperature sensor C – | ||
P04CE | Wiring, EGR temperature sensor, ECM | |
circuit malfunction | ||
Exhaust gas recirculation (EGR) temperature sensor C – | ||
P04CF | Wiring, EGR temperature sensor, ECM | |
circuit malfunction | ||
Exhaust gas recirculation (EGR) temperature sensor C – | ||
P04D0 | Wiring, EGR temperature sensor, ECM | |
circuit low | ||
Exhaust gas recirculation (EGR) temperature sensor C – | ||
P04D1 | Wiring, EGR temperature sensor, ECM | |
circuit high | ||
Exhaust gas recirculation (EGR) temperature sensor C – | ||
P04D2 | Wiring, EGR temperature sensor, ECM | |
circuit intermittent/erratic | ||
P04D3 | Exhaust brake – input circuit malfunction | Wiring |
P04D4 | Exhaust brake – input circuit range/performance | Wiring |
P04D5 | Exhaust brake – input circuit low | Wiring |
P04D6 | Exhaust brake – input circuit high | Wiring |
P04D7 | Exhaust brake – circuit intermittent/erratic | Wiring |
P04D8 | Excessive time to enter closed loop EGR control | – |
P04D9 | Closed loop EGR control, limit reached – low flow detected | – |
P04DA | Closed loop EGR control, limit reached – high flow detected | – |
P04DB | Crankcase breather system disconnected | – |
P0500 | Vehicle speed sensor (VSS) – circuit malfunction | Wiring, VSS, ECM |
P0501 | Vehicle speed sensor (VSS) – range/performance problem | Wiring, speedometer, VSS, CAN data bus |
P0502 | Vehicle speed sensor (VSS) – low input | Wiring short to earth, VSS, ECM |
Wiring, poor connection, other connected system, | ||
P0503 | Vehicle speed sensor (VSS) – intermittent/erratic/high input | |
instrument panel, VSS | ||
P0504 | Brake pedal position (BPP) switch A/B – correlation | Wiring, mechanical fault |
Wiring, ISC actuator/IAC valve, throttle motor, throttle | ||
P0505 | Idle speed control (ISC) system – malfunction | |
valve tight/sticking, ECM | ||
Wiring, ISC actuator/IAC valve, throttle motor, throttle | ||
P0506 | Idle speed control (ISC) system – rpm lower than expected | |
valve tight/sticking, ECM | ||
Wiring, ISC actuator/IAC valve, throttle motor, throttle | ||
P0507 | Idle speed control (ISC) system – rpm higher than expected | |
valve tight/sticking, ECM | ||
P0508 | Idle air control (IAC) – circuit low | Wiring short to earth, IAC valve, ECM |
P0509 | Idle air control (IAC) – circuit high | Wiring short to positive, IAC valve, ECM |
P050A | Idle air control (IAC) valve, cold start – performance problem | Wiring, IAC valve, ECM |
P050B | Ignition timing, cold start – performance problem | Wiring, CKP sensor, CMP sensor, mechanical fault, ECM |
Engine coolant temperature (ECT) sensor, cold start – | ||
P050C | Wiring, ECT sensor, ECM | |
performance problem | ||
P050D | Cold start rough idle | Wiring, IAC valve, intake manifold air leak, ECM |
P050E | Exhaust temperature, cold start – out of range | Wiring, exhaust gas temperature sensor, ECM |
P050F | Brake booster pressure sensor – low | Wiring, brake booster pressure sensor |
P0510 | Closed throttle position (CTP) switch – circuit malfunction | Wiring, CTP switch, ECM |
P0511 | Idle air control (IAC) – circuit malfunction | Wiring, poor connection, IAC valve, ECM |
P0512 | Starter request circuit – malfunction | Wiring, immobilizer system, relay |
P0513 | Incorrect immobilizer key | Immobilizer system |
P0514 | Battery temperature sensor – circuit range/performance | Wiring, poor connection, battery temperature sensor |
P0515 | Battery temperature sensor – circuit malfunction | Wiring, poor connection, battery temperature sensor |
P0516 | Battery temperature sensor – circuit low | Wiring short to earth, battery temperature sensor, ECM |
Wiring short to positive, battery temperature sensor, | ||
P0517 | Battery temperature sensor – circuit high | |
ECM | ||
P0518 | Idle air control (IAC) – circuit intermittent | Wiring, poor connection, IAC valve, ECM |
P0519 | Idle air control (IAC) – circuit performance | Wiring, poor connection, IAC valve, ECM |
P051A | Crankcase pressure sensor – circuit malfunction | Wiring, crankcase pressure sensor, ECM |
P051B | Crankcase pressure sensor – circuit range/performance | Wiring, crankcase pressure sensor, ECM |
P051C | Crankcase pressure sensor – circuit low | Wiring, crankcase pressure sensor, ECM |
P051D | Crankcase pressure sensor – circuit high | Wiring, crankcase pressure sensor, ECM |
P051E | Crankcase pressure sensor – circuit intermittent | Wiring, crankcase pressure sensor, ECM |
Positive crankcase ventilation (PCV) filter – PCV filter | ||
P051F | – | |
restricted | ||
P0520 | Engine oil pressure sensor/switch – circuit malfunction | Wiring, engine oil pressure sensor/switch, ECM |
Engine oil pressure sensor/switch – range/performance | ||
P0521 | Engine oil pressure sensor/switch | |
problem | ||
Wiring short to earth, engine oil pressure sensor/switch, | ||
P0522 | Engine oil pressure sensor/switch – low voltage | |
ECM | ||
Wiring short to positive, engine oil pressure | ||
P0523 | Engine oil pressure sensor/switch – high voltage | |
sensor/switch, ECM | ||
P0524 | Engine oil pressure too low | Mechanical fault |
Cruise control system, actuator control – circuit | ||
P0525 | Wiring, poor connection, cruise control actuator | |
range/performance | ||
Engine coolant blower motor speed sensor – circuit | Wiring, poor connection, blower motor speed sensor, | |
P0526 | ||
malfunction | ECM | |
Engine coolant blower motor speed sensor – circuit | ||
P0527 | Wiring, poor connection, blower motor speed sensor | |
range/performance | ||
Wiring, poor connection, blower motor speed sensor, | ||
P0528 | Engine coolant blower motor speed sensor – no signal | |
ECM | ||
Engine coolant blower motor speed sensor – circuit | ||
P0529 | Wiring, poor connection, ECM | |
intermittent | ||
Wiring, CKP sensor, CMP sensor, camshaft position | ||
P052A | Camshaft timing – cold start, bank 1 – timing over-advanced | |
(CMP) actuator, mechanical fault, ECM | ||
Wiring, CKP sensor, CMP sensor, camshaft position | ||
P052B | Camshaft timing – cold start, bank 1 – timing over-retarded | |
(CMP) actuator, mechanical fault, ECM | ||
Wiring, CKP sensor, CMP sensor, camshaft position | ||
P052C | Camshaft timing – cold start, bank 2 – timing over-advanced | |
(CMP) actuator, mechanical fault, ECM | ||
Wiring, CKP sensor, CMP sensor, camshaft position | ||
P052D | Camshaft timing – cold start, bank 2 – timing over-retarded | |
(CMP) actuator, mechanical fault, ECM | ||
Positive crankcase ventilation (PCV) regulator valve – | ||
P052E | – | |
performance malfunction | ||
P052F | Glow plug control module – system voltage malfunction | Wiring, glow plug control module |
P0530 | AC refrigerant pressure sensor – circuit malfunction | Wiring, AC refrigerant pressure sensor, ECM |
P0531 | AC refrigerant pressure sensor – range/performance problem | AC refrigerant pressure sensor |
AC refrigerant pressure too low (incorrectly charged), | ||
P0532 | AC refrigerant pressure sensor – low input | |
wiring, AC refrigerant pressure sensor, ECM | ||
AC refrigerant pressure too high (cooling fault/incorrectly | ||
P0533 | AC refrigerant pressure sensor – high input | |
charged), wiring, AC refrigerant pressure sensor, ECM | ||
P0534 | AC refrigerant charge loss | AC leak, wiring, AC refrigerant pressure sensor |
Wiring, poor connection, AC evaporator temperature | ||
P0535 | AC evaporator temperature sensor – circuit malfunction | |
sensor, ECM | ||
AC evaporator temperature sensor – circuit | Wiring, poor connection, AC evaporator temperature | |
P0536 | ||
range/performance | sensor, ECM | |
Wiring short to earth, AC evaporator temperature sensor, | ||
P0537 | AC evaporator temperature sensor – circuit low | |
ECM | ||
Wiring short to positive, AC evaporator temperature | ||
P0538 | AC evaporator temperature sensor – circuit high | |
sensor, ECM | ||
Wiring, poor connection, AC evaporator temperature | ||
P0539 | AC evaporator temperature sensor – circuit intermittent | |
sensor, ECM | ||
P053A | Crankcase breather heater – open circuit | Wiring, crankcase breather heater, ECM |
P053B | Crankcase breather heater – circuit low | Wiring, crankcase breather heater, ECM |
P053C | Crankcase breather heater – circuit high | Wiring, crankcase breather heater, ECM |
P053D | Crankcase breather heater – performance problem | Wiring, crankcase breather heater, ECM |
P053F | Cold start fuel pressure – performance problem | – |
P0540 | Intake air heater A – circuit malfunction | Wiring, relay, intake air heater |
P0541 | Intake air heater A – circuit low | Wiring short to earth, intake air heater |
P0542 | Intake air heater A – circuit high | Wiring short to positive, intake air heater |
P0543 | Intake air heater A – open circuit | Wiring, intake air heater |
Exhaust gas temperature (EGT) sensor 1, bank 1 – circuit | ||
P0544 | Wiring, EGT sensor, ECM | |
malfunction | ||
P0545 | Exhaust gas temperature (EGT) sensor 1, bank 1 – low input | Wiring short to earth, EGT sensor, ECM |
P0546 | Exhaust gas temperature (EGT) sensor 1, bank 1 – high input | Wiring short to positive, EGT sensor, ECM |
Exhaust gas temperature (EGT) sensor 1, bank 2 – circuit | ||
P0547 | Wiring, poor connection, EGT sensor, ECM | |
malfunction | ||
P0548 | Exhaust gas temperature (EGT) sensor 1, bank 2 – circuit low | Wiring short to earth, EGT sensor, ECM |
Exhaust gas temperature (EGT) sensor 1, bank 2 – circuit | ||
P0549 | Wiring short to positive, EGT sensor, ECM | |
high | ||
Camshaft position (CMP) sensor B, cold start – timing over- | ||
P054A | Wiring, CMP sensor | |
advanced | ||
Camshaft position (CMP) sensor B, cold start – timing over- | ||
P054B | Wiring, CMP sensor | |
retarded | ||
Camshaft position (CMP) sensor B, cold start – timing over- | ||
P054C | Wiring, CMP sensor | |
advanced | ||
Camshaft position (CMP) sensor B, cold start – timing over- | ||
P054D | Wiring, CMP sensor | |
retarded | ||
P054E | Idle control system – fuel quantity lower than expected | – |
P054F | Idle control system – fuel quantity higher than expected | – |
Power steering pressure (PSP) sensor/switch – circuit | ||
P0550 | Wiring, PSP sensor/switch, ECM | |
malfunction | ||
Power steering pressure (PSP) sensor/switch – | ||
P0551 | PAS system, PSP sensor/switch | |
range/performance problem | ||
P0552 | Power steering pressure (PSP) sensor/switch – low input | Wiring short to earth, PSP sensor/switch, ECM |
P0553 | Power steering pressure (PSP) sensor/switch – high input | Wiring short to positive, PSP sensor/switch, ECM |
Power steering pressure (PSP) sensor/switch – circuit | ||
P0554 | Wiring, poor connection, PSP sensor/switch, ECM | |
intermittent | ||
Wiring, poor connection, brake booster pressure sensor, | ||
P0555 | Brake booster pressure sensor – circuit malfunction | |
ECM | ||
Wiring, poor connection, brake booster pressure sensor, | ||
P0556 | Brake booster pressure sensor – circuit range/performance | |
ECM | ||
Wiring short to earth, brake booster pressure sensor, | ||
P0557 | Brake booster pressure sensor – circuit low input | |
ECM | ||
Wiring short to positive, brake booster pressure sensor, | ||
P0558 | Brake booster pressure sensor – circuit high input | |
ECM | ||
Wiring, poor connection, brake booster pressure sensor, | ||
P0559 | Brake booster pressure sensor – circuit intermittent | |
ECM | ||
P055A | Engine oil pressure sensor/switch B – circuit malfunction | Wiring, engine oil pressure sensor/switch, ECM |
Engine oil pressure sensor/switch B – circuit | ||
P055B | Wiring, engine oil pressure sensor/switch, ECM | |
range/performance | ||
P055C | Engine oil pressure sensor/switch B – circuit low | Wiring, engine oil pressure sensor/switch, ECM |
P055D | Engine oil pressure sensor/switch B – circuit high | Wiring, engine oil pressure sensor/switch, ECM |
P0560 | System voltage – malfunction | Wiring, poor connection, battery, alternator |
P0561 | System voltage – unstable | Wiring, poor connection, battery, alternator |
P0562 | System voltage – low | Wiring, poor connection, battery, alternator |
P0563 | System voltage – high | Alternator |
Cruise control system, multi-function switch input A – circuit | Wiring, poor connection, multi-function switch, | |
P0564 | ||
malfunction | mechanical fault | |
P0565 | Cruise control master switch, ON signal – malfunction | Wiring, cruise control master switch, ECM |
P0566 | Cruise control master switch, OFF signal – malfunction | Wiring, cruise control master switch, ECM |
P0567 | Cruise control selector switch, RESUME signal – malfunction | Wiring, cruise control selector switch, ECM |
P0568 | Cruise control master switch, SET signal – malfunction | Wiring, cruise control master switch, ECM |
P0569 | Cruise control selector switch, COAST signal – malfunction | Wiring, cruise control selector switch, ECM |
Wiring, cruise control distance range control module, | ||
P056A | Cruise control increase distance signal malfunction | |
ECM | ||
Wiring, cruise control distance range control module, | ||
P056B | Cruise control decrease distance signal malfunction | |
ECM | ||
P056C | Cruise control, cancel signal | – |
P0570 | Cruise control system, APP sensor signal – malfunction | Wiring, APP sensor, ECM |
P0571 | Cruise control/brake switch A – circuit malfunction | Wiring, cruise control/brake switch, ECM |
P0572 | Cruise control/brake switch A – circuit low | Wiring short to earth, cruise control/brake switch, ECM |
P0573 | Cruise control/brake switch A – circuit high | Wiring short to positive, cruise control/brake switch, ECM |
P0574 | Cruise control system – vehicle speed too high | Mechanical fault |
P0575 | Cruise control system – input circuit malfunction | Wiring, poor connection, mechanical fault, ECM |
P0576 | Cruise control system – input circuit low | Wiring short to earth |
P0577 | Cruise control system – input circuit high | Wiring short to positive |
Cruise control system, multi-function switch input A – circuit | Wiring, poor connection, multi-function switch, | |
P0578 | ||
stuck | mechanical fault | |
Cruise control system, multi-function switch input A – circuit | Wiring, poor connection, multi-function switch, | |
P0579 | ||
range/performance | mechanical fault | |
P057A | Brake pedal position (BPP) sensor – circuit open | Wiring, BPP sensor, ECM |
Brake pedal position (BPP) sensor – circuit | ||
P057B | Wiring, BPP sensor, ECM | |
range/performance | ||
P057C | Brake pedal position (BPP) sensor – circuit low | Wiring, BPP sensor, ECM |
P057D | Brake pedal position (BPP) sensor – circuit high | Wiring, BPP sensor, ECM |
P057E | Brake pedal position (BPP) sensor – circuit intermittent/erratic | Wiring, BPP sensor, ECM |
Cruise control system, multi-function switch input A – circuit | Wiring short to earth, multi-function switch, mechanical | |
P0580 | ||
low | fault | |
Cruise control system, multi-function switch input A – circuit | Wiring short to positive, multi-function switch, mechanical | |
P0581 | ||
high | fault | |
P0582 | Cruise control system, vacuum control – open circuit | Wiring, vacuum control solenoid |
P0583 | Cruise control system, vacuum control – circuit low | Wiring short to earth, vacuum control solenoid |
P0584 | Cruise control system, vacuum control – circuit high | Wiring short to positive, vacuum control solenoid |
Cruise control system, multi-function switch input A/B – | ||
P0585 | Mechanical fault | |
correlation | ||
P0586 | Cruise control system, vent control – open circuit | Wiring, vent control solenoid |
P0587 | Cruise control system, vent control – circuit low | Wiring short to earth, vent control solenoid |
P0588 | Cruise control system, vent control – circuit high | Wiring short to positive, vent control solenoid |
Cruise control system, multi-function switch input B – circuit | Wiring, poor connection, multi-function switch, | |
P0589 | ||
malfunction | mechanical fault | |
Cruise control system, multi-function switch input B – circuit | Wiring, poor connection, multi-function switch, | |
P0590 | ||
stuck | mechanical fault | |
Cruise control system, multi-function switch input B – circuit | Wiring, poor connection, multi-function switch, | |
P0591 | ||
range/performance | mechanical fault | |
Cruise control system, multi-function switch input B – circuit | Wiring short to earth, multi-function switch, mechanical | |
P0592 | ||
low | fault | |
Cruise control system, multi-function switch input B – circuit | Wiring short to positive, multi-function switch, mechanical | |
P0593 | ||
high | fault | |
P0594 | Cruise control system, actuator control – open circuit | Wiring, actuator |
P0595 | Cruise control system, actuator control – circuit low | Wiring short to earth, actuator |
P0596 | Cruise control system, actuator control – circuit high | Wiring short to positive, actuator |
P0597 | Thermostat heater control system – open circuit | Wiring, relay, thermostat heater |
P0598 | Thermostat heater control system – circuit low | Wiring short to earth, relay, thermostat heater |
P0599 | Thermostat heater control system – circuit high | Wiring short to positive, relay, thermostat heater |
P0600 | CAN data bus – malfunction | Wiring, connected system, ECM |
P0601 | Engine control module (ECM) – memory check sum error | ECM |
P0602 | Engine control module (ECM) – programming error | ECM |
P0603 | Engine control module (ECM) – KAM error | ECM |
P0604 | Engine control module (ECM) – RAM error | ECM |
P0605 | Engine control module (ECM) – ROM error | ECM |
Engine control module (ECM)/powertrain control module | ||
P0606 | ECM/PCM | |
(PCM) – processor fault | ||
P0607 | Engine control module (ECM) – performance problem | ECM |
P0608 | Engine control module (ECM), VSS output A – malfunction | ECM |
P0609 | Engine control module (ECM), VSS output B – malfunction | ECM |
Engine control module (ECM), monitoring processor | ||
P060A | ECM | |
performance problem | ||
P060B | Engine control module (ECM), A/D processing performance | ECM |
Engine control module (ECM), main processor – performance | ||
P060C | ECM | |
problem | ||
Engine control module (ECM), accelerator pedal position – | ||
P060D | ECM | |
performance problem | ||
Engine control module (ECM), throttle position (TP) – | ||
P060E | ECM | |
performance problem | ||
Engine control module (ECM), engine coolant temperature | ||
P060F | ECM | |
(ECT) – performance problem | ||
P0610 | Engine control module (ECM) – vehicle options error | ECM |
P0611 | Fuel injector control module – performance problem | Fuel injector control module |
P0612 | Fuel injector control module – control relay circuit | Wiring, relay, fuel injector control module |
P0613 | Transmission control module (TCM) – processor error | TCM |
Engine control module (ECM)/transmission control module | ||
P0614 | ECM/TCM | |
(TCM) – mismatch | ||
P0615 | Starter motor relay – circuit malfunction | Wiring, poor connection, starter motor relay, ECM |
P0616 | Starter motor relay – circuit low | Wiring short to earth, starter motor relay, ECM |
P0617 | Starter motor relay – circuit high | Wiring short to positive, starter motor relay, ECM |
P0618 | Alternative fuel control module – KAM error | Alternative fuel control module |
P0619 | Alternative fuel control module – RAM/ROM error | Alternative fuel control module |
Engine control module (ECM), engine torque – performance | ||
P061A | ECM | |
problem | ||
Engine control module (ECM), torque calculation – | ||
P061B | ECM | |
performance problem | ||
Engine control module (ECM), engine rpm – performance | ||
P061C | ECM | |
problem | ||
Engine control module (ECM), engine air mass – performance | ||
P061D | ECM | |
problem | ||
Engine control module (ECM), brake pedal position (BPP) | ||
P061E | ECM | |
switch/sensor – performance problem | ||
Engine control module (ECM), throttle actuator controller – | ||
P061F | ECM | |
performance problem | ||
P0620 | Alternator, control – circuit malfunction | Wiring, alternator, battery, ECM |
P0621 | Alternator warning lamp – circuit malfunction | Wiring, alternator warning lamp, ECM |
P0622 | Alternator field control – circuit malfunction | Wiring, alternator, battery, ECM |
P0623 | Alternator warning lamp, control – circuit malfunction | Wiring, poor connection, bulb, ECM |
P0624 | Filler cap warning lamp, control – circuit malfunction | Wiring, poor connection, bulb, ECM |
P0625 | Alternator field terminal – circuit low | Wiring short to earth, alternator |
P0626 | Alternator field terminal – circuit high | Wiring short to positive, alternator |
P0627 | Fuel pump (FP) control – open circuit | Wiring, relay, fuel pump (FP) |
P0628 | Fuel pump (FP) control – circuit low | Wiring short to earth, relay, fuel pump (FP) |
P0629 | Fuel pump (FP) control – circuit high | Wiring short to positive, relay, fuel pump (FP) |
P062A | Fuel pump (FP) A – control circuit range/performance | Wiring, FP, ECM |
Engine control module (ECM), fuel injector control – | ||
P062B | ECM | |
performance problem | ||
Engine control module (ECM), vehicle speed – performance | ||
P062C | ECM | |
problem | ||
P062D | Injector control module, bank 1 – performance problem | Wiring, injector control module, ECM |
P062E | Injector control module, bank 2 – performance problem | Wiring, injector control module, ECM |
P062F | Engine control module (ECM), EEPROM error | ECM |
P0630 | VIN not programmed or mismatch – ECM/PCM | ECM/PCM |
P0631 | VIN not programmed or mismatch – TCM | TCM |
P0632 | Odometer not programmed – ECM/PCM | Programming, ECM/PCM |
P0633 | Immobilizer key not programmed – ECM/PCM | Programming, ECM/PCM |
P0634 | PCM/ECM/TCM – internal temperature too high | Mechanical fault, PCM/ECM/TCM |
P0635 | Power steering control – circuit malfunction | Wiring, poor connection, PSP sensor/switch, ECM |
P0636 | Power steering control – circuit low | Wiring short to earth, PSP sensor/switch, ECM |
P0637 | Power steering control – circuit high | Wiring short to positive, PSP sensor/switch, ECM |
Throttle actuator control (TAC), bank 1 – range/performance | Basic setting not carried out (if applicable), ISC | |
P0638 | ||
problem | actuator/throttle motor, APP sensor | |
Throttle actuator control (TAC), bank 2 – range/performance | ||
P0639 | Wiring, throttle control unit | |
problem | ||
P063A | Generator voltage monitoring – circuit malfunction | Wiring, generator, ECM |
P063B | Generator voltage monitoring – circuit range/performance | Wiring, generator, ECM |
P063C | Generator voltage monitoring – circuit low | Wiring, generator, ECM |
P063D | Generator voltage monitoring – circuit high | Wiring, generator, ECM |
Throttle control unit, automatic configuration – input not | ||
P063E | Wiring, throttle control unit, ECM | |
present | ||
Engine coolant temperature (ECT) sensor, automatic | ||
P063F | Wiring, ECT sensor, ECM | |
configuration – input not present | ||
P0640 | Intake air heater control – circuit malfunction | Wiring, relay, intake air heater |
P0641 | Sensor reference voltage A – open circuit | Wiring |
P0642 | Sensor reference voltage A – circuit low | Wiring |
P0643 | Sensor reference voltage A – circuit high | Wiring short to positive |
P0644 | Driver display, serial communication – circuit malfunction | Wiring, CAN data bus, ECM |
P0645 | AC compressor clutch relay – circuit malfunction | Wiring, AC compressor clutch relay |
P0646 | AC compressor clutch relay – circuit low | Wiring short to earth, AC compressor clutch relay |
P0647 | AC compressor clutch relay – circuit high | Wiring short to positive, AC compressor clutch relay |
P0648 | Immobilizer warning lamp, control – circuit malfunction | Wiring, poor connection, bulb, ECM |
P0649 | Cruise control indicator lamp, control – circuit malfunction | Wiring, poor connection, bulb, ECM |
P064A | Fuel pump (FP) control module – malfunction | Wiring, FP, ECM |
P064B | Power take-off (PTO) control module – malfunction | Wiring, PTO control module, ECM |
P064C | Glow plug control module – malfunction | Wiring, glow plug, ECM |
Engine control module (ECM), HO2S processor, bank 1 – | ||
P064D | ECM | |
performance problem | ||
Engine control module (ECM), O2S processor, bank 2 – | ||
P064E | ECM | |
performance problem | ||
Unauthorized software – non original equipment calibration | ||
P064F | Unauthorized software | |
detected | ||
P0650 | Malfunction indicator lamp (MIL), control – circuit malfunction | Wiring, MIL, ECM |
P0651 | Sensor reference voltage B – open circuit | Wiring |
P0652 | Sensor reference voltage B – circuit low | Wiring short to earth |
P0653 | Sensor reference voltage B – circuit high | Wiring short to positive |
P0654 | Engine rpm, output – circuit malfunction | Wiring, ECM |
P0655 | Engine hot lamp output – circuit malfunction | Wiring, engine hot lamp, ECM |
P0656 | Fuel level output – circuit malfunction | Wiring, ECM |
P0657 | Actuator supply voltage – open circuit | Wiring |
P0658 | Actuator supply voltage – circuit low | Wiring short to earth, actuator |
P0659 | Actuator supply voltage – circuit high | Wiring short to positive, actuator |
P065A | Generator – performance problem | Wiring, generator, ECM |
P065B | Generator – control circuit range/performance | Wiring, generator, ECM |
P065C | Generator – mechanical fault/performance problem | Generator |
P065D | Reductant system malfunction lamp – circuit malfunction | Wiring, reductant system malfunction lamp, ECM |
Intake manifold air control actuator, bank 1 – performance | ||
P065E | Wiring, intake manifold air control actuator, ECM | |
problem | ||
Intake manifold air control actuator bank 2 – performance | ||
P065F | Wiring, intake manifold air control actuator, ECM | |
problem | ||
P0660 | Intake manifold air control solenoid, bank 1 – open circuit | Wiring, intake manifold air control solenoid |
P0661 | Intake manifold air control solenoid, bank 1 – circuit low | Wiring short to earth, intake manifold air control solenoid |
Wiring short to positive, intake manifold air control | ||
P0662 | Intake manifold air control solenoid, bank 1 – circuit high | |
solenoid | ||
P0663 | Intake manifold air control solenoid, bank 2 – open circuit | Wiring, intake manifold air control solenoid |
P0664 | Intake manifold air control solenoid, bank 2 – circuit low | Wiring short to earth, intake manifold air control solenoid |
P0665 | Intake manifold air control solenoid, bank 2 – circuit high | Wiring short to positive, intake manifold |
ECM/PCM/TCM internal temperature sensor – circuit | Poor connection, internal temperature sensor, | |
P0666 | ||
malfunction | ECM/PCM/TCM | |
ECM/PCM/TCM internal temperature sensor – | Poor connection, internal temperature sensor, | |
P0667 | ||
range/performance problem | ECM/PCM/TCM | |
Internal short to earth, internal temperature sensor, | ||
P0668 | ECM/PCM/TCM internal temperature sensor – circuit low | |
ECM/PCM/TCM | ||
Internal short to positive, internal temperature sensor, | ||
P0669 | ECM/PCM/TCM internal temperature sensor – circuit high | |
ECM/PCM/TCM | ||
P066A | Glow plug, cylinder 1 – circuit low | Wiring, glow plug, ECM |
P066B | Glow plug, cylinder 1 – circuit high | Wiring, glow plug, ECM |
P066C | Glow plug, cylinder 2 – circuit low | Wiring, glow plug, ECM |
P066D | Glow plug, cylinder 2 – circuit high | Wiring, glow plug, ECM |
P066E | Glow plug, cylinder 3 – circuit low | Wiring, glow plug, ECM |
P066F | Glow plug, cylinder 3 – circuit high | Wiring, glow plug, ECM |
Wiring, poor connection, glow plug control module, glow | ||
P0670 | Glow plug control module – circuit malfunction | |
plug, ECM | ||
Wiring, poor connection, relay, glow plug control module, | ||
P0671 | Glow plug, cylinder 1 – circuit malfunction | |
glow plug, ECM | ||
Wiring, poor connection, relay, glow plug control module, | ||
P0672 | Glow plug, cylinder 2 – circuit malfunction | |
glow plug, ECM | ||
Wiring, poor connection, relay, glow plug control module, | ||
P0673 | Glow plug, cylinder 3 – circuit malfunction | |
glow plug, ECM | ||
Wiring, poor connection, relay, glow plug control module, | ||
P0674 | Glow plug, cylinder 4 – circuit malfunction | |
glow plug, ECM | ||
Wiring, poor connection, relay, glow plug control module, | ||
P0675 | Glow plug, cylinder 5 – circuit malfunction | |
glow plug, ECM | ||
Wiring, poor connection, relay, glow plug control module, | ||
P0676 | Glow plug, cylinder 6 – circuit malfunction | |
glow plug, ECM | ||
Wiring, poor connection, relay, glow plug control module, | ||
P0677 | Glow plug, cylinder 7 – circuit malfunction | |
glow plug, ECM | ||
Wiring, poor connection, relay, glow plug control module, | ||
P0678 | Glow plug, cylinder 8 – circuit malfunction | |
glow plug, ECM | ||
Wiring, poor connection, relay, glow plug control module, | ||
P0679 | Glow plug, cylinder 9 – circuit malfunction | |
glow plug, ECM | ||
P067A | Glow plug, cylinder 4 – circuit low | Wiring, glow plug, ECM |
P067B | Glow plug, cylinder 4 – circuit high | Wiring, glow plug, ECM |
P067C | Glow plug, cylinder 5 – circuit low | Wiring, glow plug, ECM |
P067D | Glow plug, cylinder 5 – circuit high | Wiring, glow plug, ECM |
P067E | Glow plug, cylinder 6 – circuit low | Wiring, glow plug, ECM |
P067F | Glow plug, cylinder 6 – circuit high | Wiring, glow plug, ECM |
Wiring, poor connection, relay, glow plug control module, | ||
P0680 | Glow plug, cylinder 10 – circuit malfunction | |
glow plug, ECM | ||
Wiring, poor connection, relay, glow plug control module, | ||
P0681 | Glow plug, cylinder 11 – circuit malfunction | |
glow plug, ECM | ||
Wiring, poor connection, relay, glow plug control module, | ||
P0682 | Glow plug, cylinder 12 – circuit malfunction | |
glow plug, ECM | ||
Wiring, poor connection, glow plug control module, | ||
P0683 | Glow plug control module to ECM/PCM communication error | |
ECM/PCM | ||
Glow plug control module to ECM/PCM communication error – | Wiring, poor connection, glow plug control module, | |
P0684 | ||
range/performance problem | ECM/PCM | |
P0685 | Engine control (EC) relay – open circuit | Wiring, EC relay |
P0686 | Engine control (EC) relay – circuit low | Wiring short to earth, EC relay, ECM |
P0687 | Engine control (EC) relay – short to earth | Wiring short to earth, EC relay, ECM |
P0688 | Engine control (EC) relay – short to positive | Wiring short to positive, EC relay, ECM |
P0689 | Engine control (EC) relay – sense circuit low | Wiring short to earth, EC relay, ECM |
P068A | Engine control (EC) relay – shut-off early | Wiring, EC relay, ECM |
P068B | Engine control (EC) relay – shut-off delay | Wiring, EC relay, ECM |
P068C | Glow plug, cylinder 7 – circuit low | Wiring, glow plug, ECM |
P068D | Glow plug, cylinder 7 – circuit high | Wiring, glow plug, ECM |
P068E | Glow plug, cylinder 8 – circuit low | Wiring, glow plug, ECM |
P068F | Glow plug, cylinder 8 – circuit high | Wiring, glow plug, ECM |
P0690 | Engine control (EC) relay – sense circuit high | Wiring short to positive, EC relay, ECM |
P0691 | Engine coolant blower motor 1 – circuit low | Wiring short to earth, engine coolant blower motor, ECM |
Wiring short to positive, engine coolant blower motor, | ||
P0692 | Engine coolant blower motor 1 – circuit high | |
ECM | ||
P0693 | Engine coolant blower motor 2 – circuit low | Wiring short to earth, engine coolant blower motor, ECM |
Wiring short to positive, engine coolant blower motor, | ||
P0694 | Engine coolant blower motor 2 – circuit high | |
ECM | ||
P0695 | Engine coolant blower motor 3 – circuit low | Wiring short to earth, engine coolant blower motor |
P0696 | Engine coolant blower motor 3 – circuit high | Wiring short to positive, engine coolant blower motor |
P0697 | Sensor reference voltage C – open circuit | Wiring |
P0698 | Sensor reference voltage C – circuit low | Wiring short to earth |
P0699 | Sensor reference voltage C – circuit high | Wiring short to positive |
P069A | Glow plug, cylinder 9 – circuit low | Wiring, glow plug, ECM |
P069B | Glow plug, cylinder 9 – circuit high | Wiring, glow plug, ECM |
P069C | Glow plug, cylinder 10 – circuit low | Wiring, glow plug, ECM |
P069D | Glow plug, cylinder 10 – circuit high | Wiring, glow plug, ECM |
P069E | Fuel pump (FP) control module – MIL activation requested | Wiring, FP, FP control module, ECM |
P069F | Throttle control system warning lamp – circuit malfunction | Wiring, warning lamp, ECM |
Wiring, AC control module, AC compressor variable | ||
P06A0 | Variable AC compressor control – circuit malfunction | |
displacement solenoid, ECM | ||
Wiring, AC control module, AC compressor variable | ||
P06A1 | Variable AC compressor control – circuit low | |
displacement solenoid, ECM | ||
Wiring, AC control module, AC compressor variable | ||
P06A2 | Variable AC compressor control – circuit high | |
displacement solenoid, ECM | ||
P06A3 | Sensor reference voltage D – open circuit | Wiring, ECM |
P06A4 | Sensor reference voltage D – circuit low | Wiring, sensor short circuit, ECM |
P06A5 | Sensor reference voltage D – circuit high | Wiring, ECM |
P06A6 | Sensor reference voltage A – circuit range/performance | Wiring, ECM |
P06A7 | Sensor reference voltage B – circuit range/performance | Wiring, ECM |
P06A8 | Sensor reference voltage C – circuit range/performance | Wiring, ECM |
P06A9 | Sensor reference voltage D – circuit range/performance | Wiring, ECM |
Engine control module (ECM)/transmission control module | ||
P06AA | Wiring, ECM, TCM | |
(TCM) B – internal temperature too high | ||
Engine control module (ECM)/transmission control module | ||
P06AB | Wiring, ECM, TCM | |
(TCM), internal temperature sensor B – circuit malfunction | ||
Engine control module (ECM)/transmission control module | ||
P06AC | (TCM), internal temperature sensor B – circuit | Wiring, ECM, TCM |
range/performance | ||
Engine control module (ECM)/transmission control module | ||
P06AD | Wiring, ECM, TCM | |
(TCM), internal temperature sensor B – circuit low | ||
Engine control module (ECM)/transmission control module | ||
P06AE | Wiring, ECM, TCM | |
(TCM), internal temperature sensor B – circuit high | ||
P06AF | Torque management system – forced engine shut down mode | Wiring, ECM, TCM |
P06B0 | Sensor power supply A – open circuit | Wiring, ECM, TCM |
P06B1 | Sensor power supply A – circuit low | Wiring, ECM, TCM |
P06B2 | Sensor power supply A – circuit high | Wiring, ECM, TCM |
P06B3 | Sensor power supply B – open circuit | Wiring, ECM, TCM |
P06B4 | Sensor power supply B – circuit low | Wiring, ECM, TCM |
P06B5 | Sensor power supply B – circuit high | Wiring, ECM, TCM |
Internal control module, knock sensor (KS) processor 1 – | ||
P06B6 | Wiring, ECM, TCM | |
performance malfunction | ||
Internal control module, knock sensor (KS) processor 2 – | ||
P06B7 | Wiring, ECM, TCM | |
performance malfunction | ||
P06B8 | Internal control module, non-volatile memory – error | – |
P06B9 | Glow plug, cylinder 1 – circuit range/performance | Wiring, glow plug |
P06BA | Glow plug, cylinder 2 – circuit range/performance | Wiring, glow plug |
P06BB | Glow plug, cylinder 3 – circuit range/performance | Wiring, glow plug |
P06BC | Glow plug, cylinder 4 – circuit range/performance | Wiring, glow plug |
P06BD | Glow plug, cylinder 5 – circuit range/performance | Wiring, glow plug |
P06BE | Glow plug, cylinder 6 – circuit range/performance | Wiring, glow plug |
P06BF | Glow plug, cylinder 7 – circuit range/performance | Wiring, glow plug |
P06C0 | Glow plug, cylinder 8 – circuit range/performance | Wiring, glow plug |
P06C1 | Glow plug, cylinder 9 – circuit range/performance | Wiring, glow plug |
P06C2 | Glow plug, cylinder 10 – circuit range/performance | Wiring, glow plug |
P06C3 | Glow plug, cylinder 11 – circuit range/performance | Wiring, glow plug |
P06C4 | Glow plug, cylinder 12 – circuit range/performance | Wiring, glow plug |
P06C5 | Glow plug, cylinder 1 – incorrect | Wiring, glow plug |
P06C6 | Glow plug, cylinder 2 – incorrect | Wiring, glow plug |
P06C7 | Glow plug, cylinder 3 – incorrect | Wiring, glow plug |
P06C8 | Glow plug, cylinder 4 – incorrect | Wiring, glow plug |
P06C9 | Glow plug, cylinder 5 – incorrect | Wiring, glow plug |
P06CA | Glow plug, cylinder 6 – incorrect | Wiring, glow plug |
P06CB | Glow plug, cylinder 7 – incorrect | Wiring, glow plug |
P06CC | Glow plug, cylinder 8 – incorrect | Wiring, glow plug |
P06CD | Glow plug, cylinder 9 – incorrect | Wiring, glow plug |
P06CE | Glow plug, cylinder 10 – incorrect | Wiring, glow plug |
P06CF | Glow plug, cylinder 11 – incorrect | Wiring, glow plug |
P06D0 | Glow plug, cylinder 12 – incorrect | Wiring, glow plug |
Internal control module, ignition coil control – performance | ||
P06D1 | – | |
malfunction | ||
P06D2 | Sensor reference voltage E – circuit open | Wiring |
P06D3 | Sensor reference voltage E – circuit low | Wiring |
P06D4 | Sensor reference voltage E – circuit high | Wiring |
P06D5 | Sensor reference voltage E – circuit range/performance | Wiring |
P06D6 | Sensor reference voltage F – circuit open | Wiring |
P06D7 | Sensor reference voltage F – circuit low | Wiring |
P06D8 | Sensor reference voltage F – circuit high | Wiring |
P06D9 | Sensor reference voltage F – circuit range/performance | Wiring |
P06DA | Engine oil pressure control – circuit open | Wiring |
P06DB | Engine oil pressure control – circuit low | Wiring |
P06DC | Engine oil pressure control – circuit high | Wiring |
P06DD | Engine oil pressure control – circuit performance problem | Wiring |
Engine oil pressure control – control circuit malfunction, ON | ||
P06DE | Wiring | |
signal | ||
P06DF | Glow plug control module – memory check sum error | – |
P06E0 | Glow plug, cylinder 11 – control circuit low | Wiring, glow plug, glow plug control module, ECM |
P06E1 | Glow plug, cylinder 11 – control circuit high | Wiring, glow plug, glow plug control module, ECM |
P06E2 | Glow plug, cylinder 12 – control circuit low | Wiring, glow plug, glow plug control module, ECM |
P06E3 | Glow plug, cylinder 12 – control circuit high | Wiring, glow plug, glow plug control module, ECM |
P06E4 | Control module wake-up signal – signal error | – |
P06E5 | Glow plug control module – performance problem | Wiring, glow plug control module, ECM |
P0700 | Transmission control system, MIL request – circuit malfunction | Wiring, ECM/PCM/TCM |
P0701 | Transmission control system – range/performance problem | Wiring, ECM/PCM/TCM |
P0702 | Transmission control system – electrical | Wiring, ECM/PCM/TCM |
P0703 | Brake switch B – circuit malfunction | Wiring, brake switch, ECM/PCM/TCM |
P0704 | Clutch pedal position (CPP) switch – circuit malfunction | Wiring, CPP switch, ECM/PCM/TCM |
Transmission range (TR) sensor, PRNDL input – circuit | ||
P0705 | Wiring, TR sensor, ECM/PCM/TCM | |
malfunction | ||
Transmission range (TR) sensor – range/performance | ||
P0706 | Wiring, TR sensor | |
problem | ||
P0707 | Transmission range (TR) sensor – low input | Wiring short to earth, TR sensor, ECM/PCM/TCM |
P0708 | Transmission range (TR) sensor – high input | Wiring short to positive, TR sensor, ECM/PCM/TCM |
P0709 | Transmission range (TR) sensor – circuit intermittent | |
P070A | Transmission fluid level sensor – circuit malfunction | Wiring, transmission fluid level sensor, ECM |
P070B | Transmission fluid level sensor – circuit range/performance | Wiring, transmission fluid level sensor, ECM |
P070C | Transmission fluid level sensor – circuit low | Wiring, transmission fluid level sensor, ECM |
P070D | Transmission fluid level sensor – circuit high | Wiring, transmission fluid level sensor, ECM |
P070E | Transmission fluid level sensor – circuit intermittent/erratic | Wiring, transmission fluid level sensor, ECM |
P070F | Transmission fluid level – low | Transmission fluid level – low |
Transmission fluid temperature (TFT) sensor – circuit | ||
P0710 | Wiring, TFT sensor, ECM, ECM/PCM/TCM | |
malfunction | ||
Transmission fluid temperature (TFT) sensor – | ||
P0711 | Wiring, TFT sensor | |
range/performance problem | ||
P0712 | Transmission fluid temperature (TFT) sensor – low input | Wiring short to earth, TFT sensor, ECM/PCM/TCM |
P0713 | Transmission fluid temperature (TFT) sensor – high input | |
Transmission fluid temperature (TFT) sensor – circuit | ||
P0714 | ||
intermittent | ||
P0715 | Turbine shaft speed (TSS) sensor – circuit malfunction | Wiring, TSS sensor, ECM/PCM/TCM |
Turbine shaft speed (TSS) sensor – range/performance | ||
P0716 | Wiring, TSS sensor | |
problem | ||
P0717 | Turbine shaft speed (TSS) sensor – no signal | Wiring, TSS sensor, ECM/PCM/TCM |
P0718 | Turbine shaft speed (TSS) sensor – circuit intermittent | |
P0719 | Brake switch B – circuit low | Wiring short to earth, brake switch, ECM/PCM/TCM |
P071A | Transmission mode selection switch A – circuit malfunction | Transmission mode selection switch, ECM |
P071B | Transmission mode selection switch A – circuit low | Wiring, transmission mode selection switch, ECM |
P071C | Transmission mode selection switch A – circuit high | Transmission mode selection switch, ECM |
P071D | Transmission mode selection switch B – circuit malfunction | Wiring, transmission mode selection switch, ECM |
P071E | Transmission mode selection switch B – circuit low | Wiring, transmission mode selection switch, ECM |
P071F | Transmission mode selection switch B – circuit high | Wiring, transmission mode selection switch, ECM |
P0720 | Output shaft speed (OSS) sensor – circuit malfunction | Wiring, VSS, ECM/PCM/TCM |
Output shaft speed (OSS) sensor – range/performance | ||
P0721 | Wiring, VSS | |
problem | ||
P0722 | Output shaft speed (OSS) sensor – no signal | Wiring, VSS, ECM/PCM/TCM |
P0723 | Output shaft speed (OSS) sensor – circuit intermittent | Wiring, poor connection, VSS, ECM/PCM/TCM |
P0724 | Brake switch B – circuit high | Wiring short to positive, brake switch, ECM/PCM/TCM |
P0725 | Engine RPM input – circuit malfunction | Wiring, CKP/RPM sensor, ECM/PCM/TCM |
P0726 | Engine RPM input – range/performance problem | Wiring, CKP/RPM sensor |
P0727 | Engine RPM input – no signal | Wiring, CKP/RPM sensor, ECM/PCM/TCM |
Wiring, poor connection, CKP/RPM sensor, | ||
P0728 | Engine RPM input – circuit intermittent | |
ECM/PCM/TCM | ||
Wiring, TR sensor/switch, shift solenoids, transmission | ||
P0729 | Gear 6 – incorrect ratio | |
mechanical fault | ||
Wiring, shift solenoid (SS), transmission mechanical | ||
P072A | Transmission system – stuck in neutral | |
fault, TCM, ECM | ||
Wiring, shift solenoid (SS), transmission mechanical | ||
P072B | Transmission system – stuck in reverse | |
fault, TCM, ECM | ||
Wiring, shift solenoid (SS), transmission mechanical | ||
P072C | Transmission system – stuck in gear 1 | |
fault, TCM, ECM | ||
Wiring, shift solenoid (SS), transmission mechanical | ||
P072D | Transmission system – stuck in gear 2 | |
fault, TCM, ECM | ||
Wiring, shift solenoid (SS), transmission mechanical | ||
P072E | Transmission system – stuck in gear 3 | |
fault, TCM, ECM | ||
Wiring, shift solenoid (SS), transmission mechanical | ||
P072F | Transmission system – stuck in gear 4 | |
fault, TCM, ECM | ||
Wiring, TR sensor/switch, shift solenoids, transmission | ||
P0730 | Incorrect gear ratio | |
mechanical fault | ||
Wiring, TR sensor/switch, shift solenoids, transmission | ||
P0731 | Gear 1 – incorrect ratio | |
mechanical fault | ||
Wiring, TR sensor/switch, shift solenoids, transmission | ||
P0732 | Gear 2 – incorrect ratio | |
mechanical fault | ||
Wiring, TR sensor/switch, shift solenoids, transmission | ||
P0733 | Gear 3 – incorrect ratio | |
mechanical fault | ||
Wiring, TR sensor/switch, shift solenoids, transmission | ||
P0734 | Gear 4 – incorrect ratio | |
mechanical fault | ||
Wiring, TR sensor/switch, shift solenoids, transmission | ||
P0735 | Gear 5 – incorrect ratio | |
mechanical fault | ||
Wiring, TR sensor/switch, shift solenoids, transmission | ||
P0736 | Reverse gear – incorrect ratio | |
mechanical fault | ||
P0737 | TCM engine speed – output circuit | Wiring, TCM |
P0738 | TCM engine speed – output circuit low | Wiring, TCM |
P0739 | TCM engine speed – output circuit high | Wiring, TCM |
Wiring, shift solenoid (SS), transmission mechanical | ||
P073A | Transmission system – stuck in gear 5 | |
fault, TCM, ECM | ||
Wiring, shift solenoid (SS), transmission mechanical | ||
P073B | Transmission system – stuck in gear 6 | |
fault, TCM, ECM | ||
Wiring, shift solenoid (SS), transmission mechanical | ||
P073C | Transmission system – stuck in gear 7 | |
fault, TCM, ECM | ||
Wiring, shift solenoid (SS), transmission mechanical | ||
P073D | Transmission system – unable to engage neutral | |
fault, TCM, ECM | ||
Wiring, shift solenoid (SS), transmission mechanical | ||
P073E | Transmission system – unable to engage gear reverse | |
fault, TCM, ECM | ||
Wiring, shift solenoid (SS), transmission mechanical | ||
P073F | Transmission system – unable to engage gear 1 | |
fault, TCM, ECM | ||
P0740 | Torque converter clutch (TCC) solenoid – circuit malfunction | Wiring, TCC solenoid, ECM/PCM/TCM |
Torque converter clutch (TCC) solenoid – performance or | ||
P0741 | Wiring, TCC solenoid | |
stuck off | ||
P0742 | Torque converter clutch (TCC) solenoid – stuck on | Wiring, TCC solenoid |
P0743 | Torque converter clutch (TCC) solenoid – electrical | Wiring, TCC solenoid, ECM/PCM/TCM |
P0744 | Torque converter clutch (TCC) solenoid – circuit intermittent | Wiring, poor connection, TCC solenoid, ECM/PCM/TCM |
Transmission fluid pressure (TFP) solenoid – circuit | ||
P0745 | Wiring, TFP solenoid, ECM/PCM/TCM | |
malfunction | ||
Transmission fluid pressure (TFP) solenoid – performance or | ||
P0746 | Wiring, TFP solenoid | |
stuck off | ||
P0747 | Transmission fluid pressure (TFP) solenoid – stuck on | Wiring, TFP solenoid |
P0748 | Transmission fluid pressure (TFP) solenoid – electrical | Wiring, TFP solenoid, ECM/PCM/TCM |
Transmission fluid pressure (TFP) solenoid – circuit | ||
P0749 | Wiring, poor connection, TFP solenoid, ECM/PCM/TCM | |
intermittent | ||
Wiring, shift solenoid (SS), transmission mechanical | ||
P074A | Transmission system – unable to engage gear 2 | |
fault, TCM, ECM | ||
Wiring, shift solenoid (SS), transmission mechanical | ||
P074B | Transmission system – unable to engage gear 3 | |
fault, TCM, ECM | ||
P074C | Transmission system – unable to engage gear 4 | Wiring, SS, TCM, ECM |
Wiring, shift solenoid (SS), transmission mechanical | ||
P074D | Transmission system – unable to engage gear 5 | |
fault, TCM, ECM | ||
Wiring, shift solenoid (SS), transmission mechanical | ||
P074E | Transmission system – unable to engage gear 6 | |
fault, TCM, ECM | ||
Wiring, shift solenoid (SS), transmission mechanical | ||
P074F | Transmission system – unable to engage gear 7 | |
fault, TCM, ECM | ||
P0750 | Shift solenoid (SS) A – circuit malfunction | Wiring, shift solenoid (SS), ECM/PCM/TCM |
P0751 | Shift solenoid (SS) A – performance or stuck off | Wiring, shift solenoid |
P0752 | Shift solenoid (SS) A – stuck on | Wiring, shift solenoid |
P0753 | Shift solenoid (SS) A – electrical | Wiring, shift solenoid (SS), ECM/PCM/TCM |
Wiring, poor connection, shift solenoid (SS), | ||
P0754 | Shift solenoid (SS) A – circuit intermittent | |
ECM/PCM/TCM | ||
P0755 | Shift solenoid (SS) B – circuit malfunction | Wiring, shift solenoid (SS), ECM/PCM/TCM |
P0756 | Shift solenoid (SS) B – performance or stuck off | Wiring, shift solenoid |
P0757 | Shift solenoid (SS) B – stuck on | Wiring, shift solenoid |
P0758 | Shift solenoid (SS) B – electrical | Wiring, shift solenoid (SS), ECM/PCM/TCM |
Wiring, poor connection, shift solenoid (SS), | ||
P0759 | Shift solenoid (SS) B – circuit intermittent | |
ECM/PCM/TCM | ||
P075A | Shift solenoid (SS) G – malfunction | Wiring, SS, transmission mechanical fault, ECM |
P075B | Shift solenoid (SS) G – performance problem or stuck off | Wiring, SS, TCM, ECM |
P075C | Shift solenoid (SS) G – solenoid stuck on | Wiring, SS, transmission mechanical fault, ECM |
P075D | Shift solenoid (SS) G – electrical | Wiring, SS, TCM, ECM |
P075E | Shift solenoid (SS) G – intermittent | Wiring, SS, TCM, ECM |
P075F | Transmission fluid level – high | Transmission fluid level – high |
P0760 | Shift solenoid (SS) C – circuit malfunction | Wiring, shift solenoid (SS), ECM/PCM/TCM |
P0761 | Shift solenoid (SS) C – performance or stuck off | Wiring, shift solenoid |
P0762 | Shift solenoid (SS) C – stuck on | Wiring, shift solenoid |
P0763 | Shift solenoid (SS) C – electrical | Wiring, shift solenoid (SS), ECM/PCM/TCM |
Wiring, poor connection, shift solenoid (SS), | ||
P0764 | Shift solenoid (SS) C – circuit intermittent | |
ECM/PCM/TCM | ||
P0765 | Shift solenoid (SS) D – circuit malfunction | Wiring, shift solenoid (SS), ECM/PCM/TCM |
P0766 | Shift solenoid (SS) D – performance or stuck off | Wiring, shift solenoid |
P0767 | Shift solenoid (SS) D – stuck on | Wiring, shift solenoid |
P0768 | Shift solenoid (SS) D – electrical | Wiring, shift solenoid (SS), ECM/PCM/TCM |
Wiring, poor connection, shift solenoid (SS), | ||
P0769 | Shift solenoid (SS) D – circuit intermittent | |
ECM/PCM/TCM | ||
P076A | Shift solenoid (SS) H – malfunction | Wiring, SS, TCM, ECM |
P076B | Shift solenoid (SS) H – performance problem or stuck off | Wiring, SS, TCM, ECM |
P076C | Shift solenoid (SS) H – solenoid stuck on | Wiring, SS, TCM, ECM |
P076D | Shift solenoid (SS) H – electrical | Wiring, SS, TCM, ECM |
P076E | Shift solenoid (SS) H – intermittent | Wiring, SS, TCM, ECM |
P076F | Transmission system – gear 7 ratio incorrect | Transmission mechanical fault, VSS, incorrect tyre size |
P0770 | Shift solenoid (SS) E – circuit malfunction | Wiring, shift solenoid (SS), ECM/PCM/TCM |
P0771 | Shift solenoid (SS) E – performance or stuck off | Wiring, shift solenoid |
P0772 | Shift solenoid (SS) E – stuck on | Wiring, shift solenoid |
P0773 | Shift solenoid (SS) E – electrical | Wiring, shift solenoid (SS), ECM/PCM/TCM |
Wiring, poor connection, shift solenoid (SS), | ||
P0774 | Shift solenoid (SS) E – circuit intermittent | |
ECM/PCM/TCM | ||
P0775 | Pressure control solenoid B – malfunction | Pressure control solenoid |
P0776 | Pressure control solenoid B – performance or stuck off | Wiring, pressure control solenoid |
P0777 | Pressure control solenoid B – stuck on | Wiring, pressure control solenoid |
P0778 | Pressure control solenoid B – electrical malfunction | Wiring, pressure control solenoid |
P0779 | Pressure control solenoid B – circuit intermittent | Wiring, poor connection, pressure control solenoid |
P077A | Output speed sensor – loss of direction signal | – |
P077B | Output speed sensor – direction error | – |
P077C | Output speed sensor – circuit low | Wiring, output speed sensor, ECM/PCM/TCM |
P077D | Output speed sensor – circuit high | Wiring, output speed sensor, ECM/PCM/TCM |
Transmission fluid temperature (TFT) measurement system – | ||
P077E | Wiring, TFT sensor, ECM/PCM/TCM | |
multiple sensor correlation | ||
P077F | Reverse gear 2 – incorrect ratio | – |
Wiring, TR sensor, shift solenoids, transmission | ||
P0780 | Gear selection – shift malfunction | |
mechanical fault | ||
Wiring, TR sensor, shift solenoids, transmission | ||
P0781 | Gear selection, 1-2 – shift malfunction | |
mechanical fault | ||
Wiring, TR sensor, shift solenoids, transmission | ||
P0782 | Gear selection, 2-3 – shift malfunction | |
mechanical fault | ||
Wiring, TR sensor, shift solenoids, transmission | ||
P0783 | Gear selection, 3-4 – shift malfunction | |
mechanical fault | ||
Wiring, TR sensor, shift solenoids, transmission | ||
P0784 | Gear selection, 4-5 – shift malfunction | |
mechanical fault | ||
P0785 | Shift/timing solenoid – circuit malfunction | Wiring, shift/timing solenoid, ECM/PCM/TCM |
P0786 | Shift/timing solenoid – range/performance problem | Wiring, shift/timing solenoid |
Wiring short to earth, shift/timing solenoid, | ||
P0787 | Shift/timing solenoid – low | |
ECM/PCM/TCM | ||
Wiring short to positive, shift/timing solenoid, | ||
P0788 | Shift/timing solenoid – high | |
ECM/PCM/TCM | ||
Wiring, poor connection, shift/timing solenoid, | ||
P0789 | Shift/timing solenoid – circuit intermittent | |
ECM/PCM/TCM | ||
P078A | Shift solenoid (SS), timing B – malfunction | Wiring, SS, transmission mechanical fault, ECM |
P078B | Shift solenoid (SS) B – range/performance problem | Wiring, SS, TCM, ECM |
P078C | Shift solenoid (SS) B, shifting-times – circuit low | Wiring, SS, TCM, ECM |
P078D | Shift solenoid (SS), timing B – circuit high | Wiring, SS, TCM, ECM |
P078E | Shift solenoid (SS) B – intermittent | Wiring, SS, TCM, ECM |
Wiring, transmission mode selection switch, | ||
P078F | Transmission mode selection switch C – circuit malfunction | |
ECM/PCM/TCM | ||
Wiring, transmission mode selection switch, | ||
P0790 | Transmission mode selection switch – circuit malfunction | |
ECM/PCM/TCM | ||
Wiring, poor connection, intermediate shaft speed | ||
P0791 | Intermediate shaft speed sensor – circuit malfunction | |
sensor, ECM/PCM/TCM | ||
Intermediate shaft speed sensor – range/performance | Wiring, poor connection, intermediate shaft speed | |
P0792 | ||
problem | sensor, ECM/PCM/TCM | |
Wiring, poor connection, short to earth, intermediate | ||
P0793 | Intermediate shaft speed sensor – no signal | |
shaft speed sensor, ECM/PCM/TCM | ||
Wiring, poor connection, intermediate shaft speed | ||
P0794 | Intermediate shaft speed sensor – circuit intermittent | |
sensor, ECM/PCM/TCM | ||
Transmission fluid pressure (TFP) solenoid C – circuit | ||
P0795 | Wiring, poor connection, TFP solenoid, ECM/PCM/TCM | |
malfunction | ||
Transmission fluid pressure (TFP) solenoid C – performance | ||
P0796 | Wiring, poor connection, TFP solenoid, ECM/PCM/TCM | |
or stuck off | ||
P0797 | Transmission fluid pressure (TFP) solenoid C – stuck on | Wiring, poor connection, TFP solenoid, ECM/PCM/TCM |
Transmission fluid pressure (TFP) solenoid C – electrical | ||
P0798 | Wiring, poor connection, TFP solenoid, ECM/PCM/TCM | |
malfunction | ||
Transmission fluid pressure (TFP) solenoid C – circuit | ||
P0799 | Wiring, poor connection, ECM/PCM/TCM | |
intermittent | ||
P079A | Transmission friction element A – slip detected | – |
P079B | Transmission friction element B – slip detected | – |
P079C | Transmission friction element C – slip detected | – |
P079D | Transmission friction element D – slip detected | – |
P079E | Transmission friction element E – slip detected | – |
P079F | Transmission friction element F – slip detected | – |
P07A0 | Transmission friction element G – slip detected | – |
P07A1 | Transmission friction element H – slip detected | – |
P07A2 | Transmission friction element A – performance or stuck off | – |
P07A3 | Transmission friction element A – stuck on | – |
P07A4 | Transmission friction element B – performance or stuck off | – |
P07A5 | Transmission friction element B – stuck on | – |
P07A6 | Transmission friction element C – performance or stuck off | – |
P07A7 | Transmission friction element C – stuck on | – |
P07A8 | Transmission friction element D – performance or stuck off | – |
P07A9 | Transmission friction element D – stuck on | – |
P07AA | Transmission friction element E – performance or stuck off | – |
P07AB | Transmission friction element E – stuck on | – |
P07AC | Transmission friction element F – performance or stuck off | – |
P07AD | Transmission friction element F – stuck on | – |
P07AE | Transmission friction element G – performance or stuck off | – |
P07AF | Transmission friction element G – stuck on | – |
P07B0 | Transmission friction element H – performance or stuck off | – |
P07B1 | Transmission friction element H – stuck on | – |
P07B2 | Transmission park position sensor/switch A – open circuit | Wiring, transmission park position sensor/switch |
P07B3 | Transmission park position sensor/switch A – circuit low | Wiring, transmission park position sensor/switch |
P07B4 | Transmission park position sensor/switch A – circuit high | Wiring, transmission park position sensor/switch |
Transmission park position sensor/switch A – circuit | ||
P07B5 | Wiring, transmission gear position switch | |
low/performance | ||
Transmission park position sensor/switch A – circuit | ||
P07B6 | Wiring, transmission park position sensor/switch | |
high/performance | ||
Transmission park position sensor/switch A – circuit | ||
P07B7 | Wiring, transmission park position sensor/switch | |
intermittent/erratic | ||
P07B8 | Transmission park position sensor/switch B – open circuit | Wiring, transmission park position sensor/switch |
P07B9 | Transmission park position sensor/switch B – circuit low | Wiring, transmission park position sensor/switch |
P07BA | Transmission park position sensor/switch B – circuit high | Wiring, transmission park position sensor/switch |
Transmission park position sensor/switch B – circuit | ||
P07BB | Wiring, transmission park position sensor/switch | |
low/performance | ||
Transmission park position sensor/switch B – circuit | ||
P07BC | Wiring, transmission park position sensor/switch | |
high/performance | ||
Transmission park position sensor/switch B – circuit | ||
P07BD | Wiring, transmission park position sensor/switch | |
intermittent/erratic | ||
P07BE | Transmission park position sensor/switch A/B – correlation | Wiring, transmission park position sensor/switch |
Input shaft speed (ISS) sensor/turbine shaft speed (TSS) | Wiring, input shaft speed (ISS) sensor, TSS sensor, | |
P07BF | ||
sensor A – circuit low | ECM/PCM/TCM | |
Input shaft speed (ISS) sensor/turbine shaft speed (TSS) | Wiring, input shaft speed (ISS) sensor, TSS sensor, | |
P07C0 | ||
sensor A – circuit high | ECM/PCM/TCM | |
Input shaft speed (ISS) sensor/turbine shaft speed (TSS) | Wiring, input shaft speed (ISS) sensor, TSS sensor, | |
P07C1 | ||
sensor B – circuit low | ECM/PCM/TCM | |
Input shaft speed (ISS) sensor/turbine shaft speed (TSS) | Wiring, input shaft speed (ISS) sensor, TSS sensor, | |
P07C2 | ||
sensor B – circuit high | ECM/PCM/TCM | |
Input shaft speed (ISS) sensor/turbine shaft speed (TSS) | Wiring, input shaft speed (ISS) sensor, TSS sensor, | |
P07C3 | ||
sensor C – circuit low | ECM/PCM/TCM | |
Input shaft speed (ISS) sensor/turbine shaft speed (TSS) | Wiring, input shaft speed (ISS) sensor, TSS sensor, | |
P07C4 | ||
sensor C – circuit high | ECM/PCM/TCM | |
P07C5 | Intermediate shaft speed sensor A – circuit low | Wiring, intermediate shaft speed sensor, ECM/PCM/TCM |
P07C6 | Intermediate shaft speed sensor A – circuit high | Wiring, intermediate shaft speed sensor, ECM/PCM/TCM |
P07C7 | Intermediate shaft speed sensor B – circuit low | Wiring, intermediate shaft speed sensor, ECM/PCM/TCM |
P07C8 | Intermediate shaft speed sensor B – circuit high | Wiring, intermediate shaft speed sensor, ECM/PCM/TCM |
P07C9 | Intermediate shaft speed sensor C – circuit low | Wiring, intermediate shaft speed sensor, ECM/PCM/TCM |
P07CA | Intermediate shaft speed sensor C – circuit high | Wiring, intermediate shaft speed sensor, ECM/PCM/TCM |
P07CB | Transmission fluid thermostat – performance problem | Wiring, transmission fluid thermostat, ECM/PCM/TCM |
P0800 | Transfer box control system, MIL request – circuit malfunction | Wiring, mechanical fault |
P0801 | Reverse inhibit circuit – circuit malfunction | Wiring, poor connection |
P0802 | Transmission control system, MIL request – open circuit | Wiring, mechanical fault |
P0803 | 1-4 Upshift (Skip shift) solenoid – circuit malfunction | Wiring, poor connection, upshift solenoid |
P0804 | 1-4 Upshift (Skip shift) warning lamp – circuit malfunction | Wiring, poor connection |
Wiring, poor connection, clutch position sensor, | ||
P0805 | Clutch position sensor – circuit malfunction | |
ECM/PCM/TCM | ||
Wiring, poor connection, clutch position sensor, | ||
P0806 | Clutch position sensor – range/performance problem | |
ECM/PCM/TCM | ||
Wiring short to earth, clutch position sensor, | ||
P0807 | Clutch position sensor – low input | |
ECM/PCM/TCM | ||
Wiring short to positive, clutch position sensor, | ||
P0808 | Clutch position sensor – high input | |
ECM/PCM/TCM | ||
Wiring, poor connection, clutch position sensor, | ||
P0809 | Clutch position sensor – circuit intermittent | |
ECM/PCM/TCM | ||
P080A | Clutch position not learned | Wiring, CPP sensor, ECM |
Shift solenoid (SS), upshift/skip shift – circuit | ||
P080B | Wiring, SS, TCM, ECM | |
range/performance | ||
P080C | Shift solenoid (SS), upshift/skip shift – circuit low | Wiring, SS, TCM, ECM |
P080D | Shift solenoid (SS), upshift/skip shift – circuit high | Wiring, SS, TCM, ECM |
P0810 | Clutch position control error | Wiring, poor connection, ECM/PCM/TCM |
Wiring, poor connection, mechanical fault, | ||
P0811 | Excessive clutch slip | |
ECM/PCM/TCM | ||
P0812 | Reverse gear – input circuit malfunction | Wiring, poor connection, ECM/PCM/TCM |
P0813 | Reverse gear – output circuit malfunction | Wiring, poor connection, ECM/PCM/TCM |
P0814 | Transmission range (TR) display – circuit malfunction | Wiring, poor connection, TR sensor, ECM/PCM/TCM |
Transmission gear selection switch, upshift – circuit | Wiring, poor connection, transmission gear selection | |
P0815 | ||
malfunction | switch, ECM/PCM/TCM | |
Transmission gear selection switch, downshift – circuit | Wiring, poor connection, transmission gear selection | |
P0816 | ||
malfunction | switch, ECM/PCM/TCM | |
P0817 | Starter disable circuit – malfunction | Wiring, poor connection, ECM/PCM/TCM |
P0818 | Driveline disconnect switch – circuit malfunction | Wiring, poor connection, upshift switch, ECM/PCM/TCM |
Transmission gear selection switch, upshift/downshift – | Wiring, poor connection, transmission gear selection | |
P0819 | ||
correlation to transmission range (TR) | switch, transmission mechanical fault, ECM/PCM/TCM | |
P081A | Starter disable circuit – signal low | Wiring, starter motor relay, ECM |
P081B | Starter disable circuit – signal high | Wiring, starter motor relay, ECM |
Wiring, PNP switch, transmission range (TR) sensor, | ||
P081C | Park position input signal – circuit malfunction | |
ECM | ||
Wiring, PNP switch, transmission range (TR) sensor, | ||
P081D | Neutral position input signal – circuit malfunction | |
ECM | ||
P081E | Transmission clutch B – excessive clutch slip | Transmission mechanical fault |
Wiring, poor connection, gear lever position sensor, | ||
P0820 | Gear lever X-Y position sensor – circuit malfunction | |
ECM/PCM/TCM | ||
Wiring, poor connection, gear lever position sensor, | ||
P0821 | Gear lever X position sensor – circuit malfunction | |
ECM/PCM/TCM | ||
Wiring, poor connection, gear lever position sensor, | ||
P0822 | Gear lever Y position sensor – circuit malfunction | |
ECM/PCM/TCM | ||
Wiring, poor connection, gear lever position sensor, | ||
P0823 | Gear lever X position sensor – circuit intermittent | |
ECM/PCM/TCM | ||
Wiring, poor connection, gear lever position sensor, | ||
P0824 | Gear lever Y position sensor – circuit intermittent | |
ECM/PCM/TCM | ||
Wiring, poor connection, gear lever push-pull switch, | ||
P0825 | Gear lever push-pull switch – circuit malfunction | |
ECM/PCM/TCM | ||
Transmission gear selection switch, upshift/downshift – circuit | ||
P0826 | Wiring, transmission gear selection switch | |
malfunction | ||
Transmission gear selection switch, upshift/downshift – circuit | ||
P0827 | Wiring short to earth, transmission gear selection switch | |
low | ||
Transmission gear selection switch, upshift/downshift – circuit | Wiring short to positive, transmission gear selection | |
P0828 | ||
high | switch | |
P0829 | 5-6 Upshift | Mechanical fault |
P082A | Gear lever X position – circuit range/performance | – |
P082B | Gear lever X position – circuit low | – |
P082C | Gear lever X position – circuit high | – |
P082D | Gear lever Y position – circuit range/performance | – |
P082E | Gear lever Y position – circuit low | – |
P082F | Gear lever Y position – circuit high | – |
P0830 | Clutch pedal position (CPP) switch A – circuit malfunction | Wiring, poor connection, CPP switch, ECM/PCM/TCM |
P0831 | Clutch pedal position (CPP) switch A – low input | Wiring short to earth, CPP switch, ECM/PCM/TCM |
P0832 | Clutch pedal position (CPP) switch A – high input | Wiring short to positive, CPP switch, ECM/PCM/TCM |
P0833 | Clutch pedal position (CPP) switch B – circuit malfunction | Wiring, poor connection, CPP switch, ECM/PCM/TCM |
P0834 | Clutch pedal position (CPP) switch B – low input | Wiring short to earth, CPP switch, ECM/PCM/TCM |
P0835 | Clutch pedal position (CPP) switch B – high input | Wiring short to positive, CPP switch, ECM/PCM/TCM |
Wiring, poor connection, four wheel drive switch, | ||
P0836 | Four wheel drive switch – circuit malfunction | |
ECM/PCM/TCM | ||
Wiring, poor connection, four wheel drive switch, | ||
P0837 | Four wheel drive switch – range/performance problem | |
ECM/PCM/TCM | ||
Wiring short to earth, four wheel drive switch, | ||
P0838 | Four wheel drive switch – low input | |
ECM/PCM/TCM | ||
Wiring short to positive, four wheel drive switch, | ||
P0839 | Four wheel drive switch – high input | |
ECM/PCM/TCM | ||
Transmission fluid pressure (TFP) sensor/switch G – circuit | ||
P083A | Wiring, transmission fluid pressure (TFP) sensor, ECM | |
malfunction | ||
Transmission fluid pressure (TFP) sensor/switch G – circuit | ||
P083B | Wiring, transmission fluid pressure (TFP) sensor, ECM | |
range/performance | ||
Transmission fluid pressure (TFP) sensor/switch G – circuit | ||
P083C | Wiring, transmission fluid pressure (TFP) sensor, ECM | |
low | ||
Transmission fluid pressure (TFP) sensor/switch G – circuit | ||
P083D | Wiring, transmission fluid pressure (TFP) sensor, ECM | |
high | ||
Transmission fluid pressure (TFP) sensor/switch G – circuit | ||
P083E | Wiring, transmission fluid pressure (TFP) sensor, ECM | |
intermittent | ||
Wiring, CPP switch, CPP switch incorrectly adjusted, | ||
P083F | Clutch pedal position (CPP) switch A/B – correlation | |
ECM | ||
Transmission fluid pressure (TFP) sensor A – circuit | ||
P0840 | Wiring, poor connection, TFP sensor, ECM/PCM/TCM | |
malfunction | ||
Transmission fluid pressure (TFP) switch A – circuit | ||
P0840 | Wiring, poor connection, TFP switch, ECM/PCM/TCM | |
malfunction | ||
Transmission fluid pressure (TFP) sensor A – | ||
P0841 | Wiring, poor connection, TFP sensor, ECM/PCM/TCM | |
range/performance problem | ||
Transmission fluid pressure (TFP) switch A – | ||
P0841 | Wiring, poor connection, TFP switch, ECM/PCM/TCM | |
range/performance problem | ||
P0842 | Transmission fluid pressure (TFP) sensor A – low input | Wiring short to earth, TFP sensor, ECM/PCM/TCM |
P0842 | Transmission fluid pressure (TFP) switch A – low input | Wiring short to earth, TFP switch, ECM/PCM/TCM |
P0843 | Transmission fluid pressure (TFP) sensor A – high input | Wiring short to positive, TFP sensor, ECM/PCM/TCM |
P0843 | Transmission fluid pressure (TFP) switch A – high input | Wiring short to positive, TFP switch, ECM/PCM/TCM |
Transmission fluid pressure (TFP) sensor A – circuit | ||
P0844 | Wiring, poor connection, TFP sensor, ECM/PCM/TCM | |
intermittent | ||
Transmission fluid pressure (TFP) switch A – circuit | ||
P0844 | Wiring, poor connection, TFP switch, ECM/PCM/TCM | |
intermittent | ||
Transmission fluid pressure (TFP) sensor B – circuit | ||
P0845 | Wiring, poor connection, TFP sensor, ECM/PCM/TCM | |
malfunction | ||
Transmission fluid pressure (TFP) switch B – circuit | ||
P0845 | Wiring, poor connection, TFP switch, ECM/PCM/TCM | |
malfunction | ||
Transmission fluid pressure (TFP) sensor B – | ||
P0846 | Wiring, poor connection, TFP sensor, ECM/PCM/TCM | |
range/performance problem | ||
Transmission fluid pressure (TFP) switch B – | ||
P0846 | Wiring, poor connection, TFP switch, ECM/PCM/TCM | |
range/performance problem | ||
P0847 | Transmission fluid pressure (TFP) sensor B – low input | Wiring short to earth, TFP sensor, ECM/PCM/TCM |
P0847 | Transmission fluid pressure (TFP) switch B – low input | Wiring short to earth, TFP switch, ECM/PCM/TCM |
P0848 | Transmission fluid pressure (TFP) sensor B – high input | Wiring short to positive, TFP sensor, ECM/PCM/TCM |
P0848 | Transmission fluid pressure (TFP) switch B – high input | Wiring short to positive, TFP switch, ECM/PCM/TCM |
Transmission fluid pressure (TFP) sensor B – circuit | ||
P0849 | Wiring, poor connection, TFP sensor, ECM/PCM/TCM | |
intermittent | ||
Transmission fluid pressure (TFP) switch B – circuit | ||
P0849 | Wiring, poor connection, TFP switch, ECM/PCM/TCM | |
intermittent | ||
Transmission fluid pressure (TFP) sensor/switch H – circuit | Wiring, transmission fluid pressure (TFP) sensor/switch, | |
P084A | ||
malfunction | ECM | |
Transmission fluid pressure (TFP) sensor/switch H – circuit | ||
P084B | Wiring, transmission fluid pressure (TFP) sensor, ECM | |
range/performance | ||
Transmission fluid pressure (TFP) sensor/switch H – circuit | Wiring, transmission fluid pressure (TFP) sensor/switch, | |
P084C | ||
low | ECM | |
Transmission fluid pressure (TFP) sensor/switch H – circuit | Wiring, transmission fluid pressure (TFP) sensor/switch, | |
P084D | ||
high | ECM | |
Transmission fluid pressure (TFP) sensor/switch H – circuit | ||
P084E | Wiring, transmission fluid pressure (TFP) sensor, ECM | |
intermittent | ||
P084F | Park/neutral position (PNP) switch – output circuit | – |
P0850 | Park/neutral position (PNP) switch – input circuit malfunction | Wiring, PNP switch, ECM/PCM/TCM |
P0851 | Park/neutral position (PNP) switch – input circuit low | Wiring short to earth, PNP switch, ECM/PCM/TCM |
P0852 | Park/neutral position (PNP) switch – input circuit high | Wiring short to positive, PNP switch, ECM/PCM/TCM |
P0853 | Drive switch – input circuit malfunction | Wiring, drive switch, ECM/PCM/TCM |
P0854 | Drive switch – input circuit low | Wiring short to earth, drive switch, ECM/PCM/TCM |
P0855 | Drive switch – input circuit high | Wiring short to positive, drive switch, ECM/PCM/TCM |
P0856 | Traction control input signal – malfunction | Wiring, poor connection, ECM/PCM/TCM |
P0857 | Traction control input signal – range/performance problem | Wiring, poor connection, ECM/PCM/TCM |
P0858 | Traction control input signal – low | Wiring short to earth, ECM/PCM/TCM |
P0859 | Traction control input signal – high | Wiring short to positive, ECM/PCM/TCM |
Gear shift control module B, communication circuit – | ||
P085A | Wiring, gear shift module, ECM | |
malfunction | ||
Gear shift control module B, communication circuit – signal | ||
P085B | Wiring, gear shift module, ECM | |
low | ||
Gear shift control module B, communication circuit – signal | ||
P085C | Wiring, gear shift module, ECM | |
high | ||
P085D | Transmission shift control module A – performance problem | – |
P085E | Transmission shift control module B – performance problem | – |
Wiring, poor connection, gear shift module, | ||
P0860 | Gear shift module communication circuit – malfunction | |
ECM/PCM/TCM | ||
P0861 | Gear shift module communication circuit – low input | Wiring short to earth, gear shift module, ECM/PCM/TCM |
Wiring short to positive, gear shift module, | ||
P0862 | Gear shift module communication circuit – high input | |
ECM/PCM/TCM | ||
Transmission control module (TCM), communication – circuit | ||
P0863 | Wiring, poor connection, TCM | |
malfunction | ||
Transmission control module (TCM), communication – | ||
P0864 | Wiring, poor connection, TCM | |
range/performance problem | ||
Transmission control module (TCM), communication – low | ||
P0865 | Wiring short to earth, TCM | |
input | ||
Transmission control module (TCM), communication – high | ||
P0866 | Wiring short to positive, TCM | |
input | ||
P0867 | Transmission fluid pressure (TFP) sensor | Wiring, poor connection, TFP sensor, ECM/PCM/TCM |
P0868 | Transmission fluid pressure (TFP) sensor – low | Wiring short to earth, TFP sensor, ECM/PCM/TCM |
P0869 | Transmission fluid pressure (TFP) sensor – high | Wiring short to positive, TFP sensor, ECM/PCM/TCM |
P086A | Neutral position (NP) sensor – circuit open | Wiring, NP sensor, ECM/PCM/TCM |
P086B | Neutral position (NP) sensor – circuit range/performance | Wiring, NP sensor, ECM/PCM/TCM |
P086C | Neutral position (NP) sensor – circuit low | Wiring, NP sensor, ECM/PCM/TCM |
P086D | Neutral position (NP) sensor – circuit high | Wiring, NP sensor, ECM/PCM/TCM |
P086E | Neutral position (NP) sensor – circuit intermittent/erratic | Wiring, NP sensor, ECM/PCM/TCM |
Transmission fluid pressure (TFP) sensor C – circuit | ||
P0870 | Wiring, poor connection, TFP sensor, ECM/PCM/TCM | |
malfunction | ||
Transmission fluid pressure (TFP) switch C – circuit | ||
P0870 | Wiring, poor connection, TFP switch, ECM/PCM/TCM | |
malfunction | ||
Transmission fluid pressure (TFP) sensor C – | ||
P0871 | Wiring, poor connection, TFP sensor, ECM/PCM/TCM | |
range/performance problem | ||
Transmission fluid pressure (TFP) switch C – | ||
P0871 | Wiring, poor connection, TFP switch, ECM/PCM/TCM | |
range/performance problem | ||
P0872 | Transmission fluid pressure (TFP) sensor C – circuit low | Wiring short to earth, TFP sensor, ECM/PCM/TCM |
P0872 | Transmission fluid pressure (TFP) switch C – circuit low | Wiring short to earth, TFP switch, ECM/PCM/TCM |
P0873 | Transmission fluid pressure (TFP) sensor C – circuit high | Wiring short to positive, TFP sensor, ECM/PCM/TCM |
P0873 | Transmission fluid pressure (TFP) switch C – circuit high | Wiring short to positive, TFP switch, ECM/PCM/TCM |
Transmission fluid pressure (TFP) sensor C – circuit | ||
P0874 | Wiring, poor connection, TFP sensor, ECM/PCM/TCM | |
intermittent | ||
Transmission fluid pressure (TFP) switch C – circuit | ||
P0874 | Wiring, poor connection, TFP switch, ECM/PCM/TCM | |
intermittent | ||
Transmission fluid pressure (TFP) sensor D – circuit | ||
P0875 | Wiring, poor connection, TFP sensor, ECM/PCM/TCM | |
malfunction | ||
Transmission fluid pressure (TFP) switch D – circuit | ||
P0875 | Wiring, poor connection, TFP switch, ECM/PCM/TCM | |
malfunction | ||
Transmission fluid pressure (TFP) sensor D – | ||
P0876 | Wiring, poor connection, TFP sensor, ECM/PCM/TCM | |
range/performance problem | ||
Transmission fluid pressure (TFP) switch D – | ||
P0876 | Wiring, poor connection, TFP switch, ECM/PCM/TCM | |
range/performance problem | ||
P0877 | Transmission fluid pressure (TFP) sensor D – circuit low | Wiring short to earth, TFP sensor, ECM/PCM/TCM |
P0877 | Transmission fluid pressure (TFP) switch D – circuit low | Wiring short to earth, TFP switch, ECM/PCM/TCM |
P0878 | Transmission fluid pressure (TFP) sensor D – circuit high | Wiring short to positive, TFP sensor, ECM/PCM/TCM |
P0878 | Transmission fluid pressure (TFP) switch D – circuit high | Wiring short to positive, TFP switch, ECM/PCM/TCM |
Transmission fluid pressure (TFP) sensor D – circuit | ||
P0879 | Wiring, poor connection, TFP sensor, ECM/PCM/TCM | |
intermittent | ||
Transmission fluid pressure (TFP) switch D – circuit | ||
P0879 | Wiring, poor connection, TFP switch, ECM/PCM/TCM | |
intermittent | ||
P087A | Clutch position sensor B – circuit malfunction | Wiring, clutch position sensor, ECM/PCM/TCM |
P087B | Clutch position sensor B – circuit range/performance | Wiring, clutch position sensor, ECM/PCM/TCM |
P087C | Clutch position sensor B – circuit low | Wiring, clutch position sensor, ECM/PCM/TCM |
P087D | Clutch position sensor B – circuit high | Wiring, clutch position sensor, ECM/PCM/TCM |
P087E | Clutch position sensor B – circuit intermittent | Wiring, clutch position sensor, ECM/PCM/TCM |
Transmission control module (TCM) – power input signal | ||
P0880 | Wiring, poor connection, TCM | |
malfunction | ||
Transmission control module (TCM) – power input signal | ||
P0881 | Wiring, poor connection, TCM | |
range/performance | ||
P0882 | Transmission control module (TCM) – power input signal low | Wiring short to earth, TCM |
P0883 | Transmission control module (TCM) – power input signal high | Wiring short to positive, TCM |
Transmission control module (TCM), power input signal – | ||
P0884 | Wiring, poor connection, TCM | |
circuit intermittent | ||
Transmission control module (TCM) power relay, control – | ||
P0885 | Wiring, poor connection, TCM power relay, TCM | |
open circuit | ||
Transmission control module (TCM) power relay, control – | ||
P0886 | Wiring short to earth, TCM power relay, TCM | |
circuit low | ||
Transmission control module (TCM) power relay, control – | ||
P0887 | Wiring short to positive, TCM power relay, TCM | |
circuit high | ||
Transmission control module (TCM) power relay, sense circuit | ||
P0888 | Wiring, poor connection, TCM power relay, TCM | |
malfunction | ||
Transmission control module (TCM) power relay, sense circuit | ||
P0889 | Wiring, poor connection, TCM power relay, TCM | |
range/performance | ||
P088A | Transmission fluid filter – filter deteriorated | – |
P088B | Transmission fluid filter – filter very deteriorated | – |
Transmission control module (TCM) power relay, sense circuit | ||
P0890 | Wiring short to earth, TCM power relay, TCM | |
low | ||
Transmission control module (TCM) power relay, sense circuit | ||
P0891 | Wiring short to positive, TCM power relay, TCM | |
high | ||
Transmission control module (TCM) power relay, sense circuit | ||
P0892 | Wiring, poor connection, TCM power relay, TCM | |
intermittent malfunction | ||
P0893 | Multiple gears engaged | Mechanical fault |
P0894 | Transmission component slipping | Mechanical fault |
P0895 | Shift time too short | Mechanical fault |
P0896 | Shift time too long | Mechanical fault |
P0897 | Transmission fluid deteriorated | Mechanical fault |
P0898 | Transmission control system – MIL request – circuit low | Wiring short to earth, poor connection |
P0899 | Transmission control system – MIL request – circuit high | Wiring short to positive, poor connection |
P089A | Gear lever X position sensor 2 – circuit malfunction | Wiring, gear lever position sensor, ECM/PCM/TCM |
P089B | Gear lever X position sensor 2 – circuit range/performance | Wiring, gear lever position sensor, ECM/PCM/TCM |
P089C | Gear lever X position sensor 2 – circuit low | Wiring, gear lever position sensor, ECM/PCM/TCM |
P089D | Gear lever X position sensor 2 – circuit high | Wiring, gear lever position sensor, ECM/PCM/TCM |
P089E | Gear lever X position sensor 2 – circuit intermittent/erratic | Wiring, gear lever position sensor, ECM/PCM/TCM |
P089F | Gear lever Y position sensor 2 – circuit malfunction | Wiring, gear lever position sensor, ECM/PCM/TCM |
P08A0 | Gear lever Y position sensor 2 – circuit range/performance | Wiring, gear lever position sensor, ECM/PCM/TCM |
P08A1 | Gear lever Y position sensor 2 – circuit low | Wiring, gear lever position sensor, ECM/PCM/TCM |
P08A2 | Gear lever Y position sensor 2 – circuit high | Wiring, gear lever position sensor, ECM/PCM/TCM |
P08A3 | Gear lever Y position sensor 2 – circuit intermittent/erratic | Wiring, gear lever position sensor, ECM/PCM/TCM |
P08A4 | Gear lever X position sensor 1/2 – correlation | Wiring, gear lever position sensor, ECM/PCM/TCM |
P08A5 | Gear lever Y position sensor 1/2 – correlation | Wiring, gear lever position sensor, ECM/PCM/TCM |
Gear lever position measurement system – multiple sensor | ||
P08A6 | Wiring, gear lever position sensor, ECM/PCM/TCM | |
correlation | ||
P0900 | Clutch actuator – open circuit | Wiring, clutch actuator, ECM/PCM/TCM |
P0901 | Clutch actuator – circuit range/performance | Wiring, poor connection, clutch actuator, ECM/PCM/TCM |
P0902 | Clutch actuator – circuit low | Wiring short to earth, clutch actuator, ECM/PCM/TCM |
P0903 | Clutch actuator – circuit high | Wiring short to positive, clutch actuator, ECM/PCM/TCM |
P0904 | Transmission gate select position circuit – malfunction | Wiring, poor connection, ECM/PCM/TCM |
Transmission gate select position circuit – range/performance | ||
P0905 | Wiring, poor connection, ECM/PCM/TCM | |
problem | ||
P0906 | Transmission gate select position circuit – low | Wiring short to earth, ECM/PCM/TCM |
P0907 | Transmission gate select position circuit – high | Wiring short to positive, ECM/PCM/TCM |
P0908 | Transmission gate select position circuit – circuit intermittent | Wiring, poor connection, ECM/PCM/TCM |
P0909 | Transmission gate select control error | Mechanical fault |
P090A | Clutch actuator B – open circuit | Wiring, clutch actuator, ECM/PCM/TCM |
P090B | Clutch actuator B – circuit range/performance | Wiring, clutch actuator, ECM/PCM/TCM |
P090C | Clutch actuator B – circuit low | Wiring, clutch actuator, ECM/PCM/TCM |
P090D | Clutch actuator B – circuit high | Wiring, clutch actuator, ECM/PCM/TCM |
Wiring, transmission gate select actuator, | ||
P0910 | Transmission gate select actuator – open circuit | |
ECM/PCM/TCM | ||
Wiring, poor connection, transmission gate select | ||
P0911 | Transmission gate select actuator – circuit range/performance | |
actuator, ECM/PCM/TCM | ||
Wiring short to earth, transmission gate select actuator, | ||
P0912 | Transmission gate select actuator – circuit low | |
ECM/PCM/TCM | ||
Wiring short to positive, transmission gate select | ||
P0913 | Transmission gate select actuator – circuit high | |
actuator, ECM/PCM/TCM | ||
P0914 | Gear shift position circuit – malfunction | Wiring, poor connection, ECM/PCM/TCM |
P0915 | Gear shift position circuit – range/performance problem | Wiring, poor connection, ECM/PCM/TCM |
P0916 | Gear shift position circuit – low | Wiring short to earth, ECM/PCM/TCM |
P0917 | Gear shift position circuit – high | Wiring short to positive, ECM/PCM/TCM |
P0918 | Gear shift position circuit – circuit intermittent | Wiring, poor connection, ECM/PCM/TCM |
P0919 | Gear shift position control – error | Wiring, poor connection, ECM/PCM/TCM |
P0920 | Gear shift forward actuator – open circuit | Wiring, gear shift forward actuator, ECM/PCM/TCM |
Wiring, poor connection, gear shift forward actuator, | ||
P0921 | Gear shift forward actuator – circuit range/performance | |
ECM/PCM/TCM | ||
Wiring short to earth, gear shift forward actuator, | ||
P0922 | Gear shift forward actuator – circuit low | |
ECM/PCM/TCM | ||
Wiring short to positive, gear shift forward actuator, | ||
P0923 | Gear shift forward actuator – circuit high | |
ECM/PCM/TCM | ||
P0924 | Gear shift reverse actuator – open circuit | Wiring, gear shift reverse actuator, ECM/PCM/TCM |
Wiring, poor connection, gear shift reverse actuator, | ||
P0925 | Gear shift reverse actuator – circuit range/performance | |
ECM/PCM/TCM | ||
Wiring short to earth, gear shift reverse actuator, | ||
P0926 | Gear shift reverse actuator – circuit low | |
ECM/PCM/TCM | ||
Wiring short to positive, gear shift reverse actuator, | ||
P0927 | Gear shift reverse actuator – circuit high | |
ECM/PCM/TCM | ||
P0928 | Gear shift lock solenoid – open circuit | Wiring, gear shift lock solenoid, ECM/PCM/TCM |
P0929 | Gear shift lock solenoid – circuit range/performance | Wiring, gear shift lock solenoid, ECM/PCM/TCM |
Gear shift lock solenoid/actuator control circuit B – open | ||
P092A | – | |
circuit | ||
Gear shift lock solenoid/actuator control circuit B – circuit | ||
P092B | – | |
range/performance | ||
P092C | Gear shift lock solenoid/actuator control circuit B – circuit low | – |
P092D | Gear shift lock solenoid/actuator control circuit B – circuit high | – |
Wiring short to earth, gear shift lock solenoid, | ||
P0930 | Gear shift lock solenoid – circuit low | |
ECM/PCM/TCM | ||
Wiring short to positive, gear shift lock solenoid, | ||
P0931 | Gear shift lock solenoid – circuit high | |
ECM/PCM/TCM | ||
Wiring, poor connection, hydraulic pressure sensor, | ||
P0932 | Hydraulic pressure sensor – circuit malfunction | |
ECM/PCM/TCM | ||
P0933 | Hydraulic pressure sensor – range/performance problem | Wiring, hydraulic pressure sensor, ECM/PCM/TCM |
Wiring short to earth, hydraulic pressure sensor, | ||
P0934 | Hydraulic pressure sensor – circuit low input | |
ECM/PCM/TCM | ||
Wiring short to positive, hydraulic pressure sensor, | ||
P0935 | Hydraulic pressure sensor – circuit high input | |
ECM/PCM/TCM | ||
Wiring, poor connection, hydraulic pressure sensor, | ||
P0936 | Hydraulic pressure sensor – circuit intermittent | |
ECM/PCM/TCM | ||
Wiring, poor connection, hydraulic oil temperature | ||
P0937 | Hydraulic oil temperature sensor – circuit malfunction | |
sensor, ECM/PCM/TCM | ||
Hydraulic oil temperature sensor – range/performance | ||
P0938 | Wiring, hydraulic oil temperature sensor, ECM/PCM/TCM | |
problem | ||
Wiring short to earth, hydraulic oil temperature sensor, | ||
P0939 | Hydraulic oil temperature sensor – circuit low input | |
ECM/PCM/TCM | ||
Wiring short to positive, hydraulic oil temperature sensor, | ||
P0940 | Hydraulic oil temperature sensor – circuit high input | |
ECM/PCM/TCM | ||
Wiring, poor connection, hydraulic oil temperature | ||
P0941 | Hydraulic oil temperature sensor – circuit intermittent | |
sensor, ECM/PCM/TCM | ||
P0942 | Hydraulic pressure unit | Mechanical fault |
P0943 | Hydraulic pressure unit – cycling period too short | Mechanical fault |
P0944 | Hydraulic pressure unit – loss of pressure | Mechanical fault |
P0945 | Hydraulic pump relay – open circuit | Wiring, hydraulic pump relay, ECM/PCM/TCM |
P0946 | Hydraulic pump relay – circuit range/performance | Wiring, hydraulic pump relay, ECM/PCM/TCM |
Wiring short to earth, hydraulic pump relay, | ||
P0947 | Hydraulic pump relay – circuit low | |
ECM/PCM/TCM | ||
Wiring short to positive, hydraulic pump relay, | ||
P0948 | Hydraulic pump relay – circuit high | |
ECM/PCM/TCM | ||
Auto shift manual (ASM) transmission – adaptive learning not | ||
P0949 | ECM/PCM/TCM | |
done | ||
Auto shift manual (ASM) transmission, control – circuit | ||
P0950 | Wiring, poor connection, ECM/PCM/TCM | |
malfunction | ||
Auto shift manual (ASM) transmission, control – | ||
P0951 | Wiring, poor connection, ECM/PCM/TCM | |
range/performance problem | ||
P0952 | Auto shift manual (ASM) transmission, control – circuit low | Wiring, poor connection, short to earth, ECM/PCM/TCM |
Wiring, poor connection, short to positive, | ||
P0953 | Auto shift manual (ASM) transmission, control – circuit high | |
ECM/PCM/TCM | ||
Auto shift manual (ASM) transmission, control – circuit | ||
P0954 | Wiring, poor connection, ECM/PCM/TCM | |
intermittent | ||
Auto shift manual (ASM) transmission, mode – circuit | ||
P0955 | Wiring, poor connection, ECM/PCM/TCM | |
malfunction | ||
Auto shift manual (ASM) transmission, mode – | ||
P0956 | Wiring, poor connection, ECM/PCM/TCM | |
range/performance problem | ||
P0957 | Auto shift manual (ASM) transmission, mode – circuit low | Wiring, poor connection, short to earth, ECM/PCM/TCM |
Wiring, poor connection, short to positive, | ||
P0958 | Auto shift manual (ASM) transmission, mode – circuit high | |
ECM/PCM/TCM | ||
Auto shift manual (ASM) transmission, mode – circuit | ||
P0959 | Wiring, poor connection, ECM/PCM/TCM | |
intermittent | ||
Wiring, poor connection, pressure control solenoid, | ||
P0960 | Pressure control (PC) solenoid A – open circuit | |
ECM/PCM/TCM | ||
Pressure control (PC) solenoid A – range/performance | Wiring, poor connection, pressure control solenoid, | |
P0961 | ||
problem | ECM/PCM/TCM | |
Wiring short to earth, pressure control solenoid, | ||
P0962 | Pressure control (PC) solenoid A – circuit low | |
ECM/PCM/TCM | ||
Wiring short to positive, pressure control solenoid, | ||
P0963 | Pressure control (PC) solenoid A – circuit high | |
ECM/PCM/TCM | ||
Wiring, poor connection, pressure control solenoid, | ||
P0964 | Pressure control (PC) solenoid B – open circuit | |
ECM/PCM/TCM | ||
Pressure control (PC) solenoid B – range/performance | Wiring, poor connection, pressure control solenoid, | |
P0965 | ||
problem | ECM/PCM/TCM | |
Wiring short to earth, pressure control solenoid, | ||
P0966 | Pressure control (PC) solenoid B – circuit low | |
ECM/PCM/TCM | ||
Wiring short to positive, pressure control solenoid, | ||
P0967 | Pressure control (PC) solenoid B – circuit high | |
ECM/PCM/TCM | ||
Wiring, poor connection, pressure control solenoid, | ||
P0968 | Pressure control (PC) solenoid C – open circuit | |
ECM/PCM/TCM | ||
Pressure control (PC) solenoid C – range/performance | Wiring, poor connection, pressure control solenoid, | |
P0969 | ||
problem | ECM/PCM/TCM | |
Wiring short to earth, pressure control solenoid, | ||
P0970 | Pressure control (PC) solenoid C – circuit low | |
ECM/PCM/TCM | ||
Wiring short to positive, pressure control solenoid, | ||
P0971 | Pressure control (PC) solenoid C – circuit high | |
ECM/PCM/TCM | ||
Wiring, poor connection, shift solenoid (SS), | ||
P0972 | Shift solenoid (SS) A – range/performance problem | |
ECM/PCM/TCM | ||
P0973 | Shift solenoid (SS) A – circuit low | Wiring short to earth, shift solenoid (SS), ECM/PCM/TCM |
Wiring short to positive, shift solenoid (SS), | ||
P0974 | Shift solenoid (SS) A – circuit high | |
ECM/PCM/TCM | ||
Wiring, poor connection, shift solenoid (SS), | ||
P0975 | Shift solenoid (SS) B – range/performance problem | |
ECM/PCM/TCM | ||
P0976 | Shift solenoid (SS) B – circuit low | Wiring short to earth, shift solenoid (SS), ECM/PCM/TCM |
Wiring short to positive, shift solenoid (SS), | ||
P0977 | Shift solenoid (SS) B – circuit high | |
ECM/PCM/TCM | ||
Wiring, poor connection, shift solenoid (SS), | ||
P0978 | Shift solenoid (SS) C – range/performance problem | |
ECM/PCM/TCM | ||
P0979 | Shift solenoid (SS) C – circuit low | Wiring short to earth, shift solenoid (SS), ECM/PCM/TCM |
Wiring short to positive, shift solenoid (SS), | ||
P0980 | Shift solenoid (SS) C – circuit high | |
ECM/PCM/TCM | ||
Wiring, poor connection, shift solenoid (SS), | ||
P0981 | Shift solenoid (SS) D – range/performance problem | |
ECM/PCM/TCM | ||
P0982 | Shift solenoid (SS) D – circuit low | Wiring short to earth, shift solenoid (SS), ECM/PCM/TCM |
Wiring short to positive, shift solenoid (SS), | ||
P0983 | Shift solenoid (SS) D – circuit high | |
ECM/PCM/TCM | ||
Wiring, poor connection, shift solenoid (SS), | ||
P0984 | Shift solenoid (SS) E – range/performance problem | |
ECM/PCM/TCM | ||
P0985 | Shift solenoid (SS) E – circuit low | Wiring short to earth, shift solenoid (SS), ECM/PCM/TCM |
Wiring short to positive, shift solenoid (SS), | ||
P0986 | Shift solenoid (SS) E – circuit high | |
ECM/PCM/TCM | ||
Transmission fluid pressure (TFP) sensor E – circuit | ||
P0987 | Wiring, poor connection, TFP sensor, ECM/PCM/TCM | |
malfunction | ||
Transmission fluid pressure (TFP) switch E – circuit | ||
P0987 | Wiring, poor connection, TFP switch, ECM/PCM/TCM | |
malfunction | ||
Transmission fluid pressure (TFP) sensor E – | ||
P0988 | Wiring, poor connection, TFP sensor, ECM/PCM/TCM | |
range/performance problem | ||
Transmission fluid pressure (TFP) switch E – | ||
P0988 | Wiring, poor connection, TFP switch, ECM/PCM/TCM | |
range/performance problem | ||
P0989 | Transmission fluid pressure (TFP) sensor E – circuit low | Wiring short to earth, TFP sensor, ECM/PCM/TCM |
P0989 | Transmission fluid pressure (TFP) switch E – circuit low | Wiring short to earth, TFP switch, ECM/PCM/TCM |
P0990 | Transmission fluid pressure (TFP) sensor E – circuit high | Wiring short to positive, TFP sensor, ECM/PCM/TCM |
P0990 | Transmission fluid pressure (TFP) switch E – circuit high | Wiring short to positive, TFP switch, ECM/PCM/TCM |
Transmission fluid pressure (TFP) sensor E – circuit | ||
P0991 | Wiring, poor connection, TFP sensor, ECM/PCM/TCM | |
intermittent | ||
Transmission fluid pressure (TFP) switch E – circuit | ||
P0991 | Wiring, poor connection, TFP switch, ECM/PCM/TCM | |
intermittent | ||
Transmission fluid pressure (TFP) sensor F – circuit | ||
P0992 | Wiring, poor connection, TFP sensor, ECM/PCM/TCM | |
malfunction | ||
Transmission fluid pressure (TFP) switch F – circuit | ||
P0992 | Wiring, poor connection, TFP switch, ECM/PCM/TCM | |
malfunction | ||
Transmission fluid pressure (TFP) sensor F – | ||
P0993 | Wiring, poor connection, TFP sensor, ECM/PCM/TCM | |
range/performance problem | ||
Transmission fluid pressure (TFP) switch F – | ||
P0993 | Wiring, poor connection, TFP switch, ECM/PCM/TCM | |
range/performance problem | ||
P0994 | Transmission fluid pressure (TFP) sensor F – circuit low | Wiring short to earth, TFP sensor, ECM/PCM/TCM |
P0994 | Transmission fluid pressure (TFP) switch F – circuit low | Wiring short to earth, TFP switch, ECM/PCM/TCM |
P0995 | Transmission fluid pressure (TFP) sensor F – circuit high | Wiring short to positive, TFP sensor, ECM/PCM/TCM |
P0995 | Transmission fluid pressure (TFP) switch F – circuit high | Wiring short to positive, TFP switch, ECM/PCM/TCM |
Transmission fluid pressure (TFP) sensor F – circuit | ||
P0996 | Wiring, poor connection, TFP sensor, ECM/PCM/TCM | |
intermittent | ||
Transmission fluid pressure (TFP) switch F – circuit | ||
P0996 | Wiring, poor connection, TFP switch, ECM/PCM/TCM | |
intermittent | ||
Wiring, poor connection, shift solenoid (SS), | ||
P0997 | Shift solenoid (SS) F – range/performance problem | |
ECM/PCM/TCM | ||
P0998 | Shift solenoid (SS) F – circuit low | Wiring short to earth, shift solenoid (SS), ECM/PCM/TCM |
Wiring short to positive, shift solenoid (SS), | ||
P0999 | Shift solenoid (SS) F – circuit high | |
ECM/PCM/TCM | ||
P099A | Shift solenoid (SS) G – control circuit range/performance | Wiring, SS, TCM, ECM |
P099B | Shift solenoid (SS) G – control circuit low | Wiring, SS, TCM, ECM |
P099C | Shift solenoid (SS) G – control circuit high | Wiring, SS, TCM, ECM |
P099D | Shift solenoid (SS) H – control circuit range/performance | Wiring, SS, TCM, ECM |
P099E | Shift solenoid (SS) H – control circuit low | Wiring, SS, TCM, ECM |
P099F | Shift solenoid (SS) H – control circuit high | Wiring, SS, TCM, ECM |
Voltage converter coolant temperature sensor – circuit | ||
P0A00 | Wiring, voltage converter coolant temperature sensor | |
malfunction | ||
Voltage converter coolant temperature sensor – circuit | ||
P0A01 | Wiring, voltage converter coolant temperature sensor | |
range/performance | ||
P0A02 | Voltage converter coolant temperature sensor – circuit low | Wiring, voltage converter coolant temperature sensor |
P0A03 | Voltage converter coolant temperature sensor – circuit high | Wiring, voltage converter coolant temperature sensor |
Voltage converter coolant temperature sensor – circuit | ||
P0A04 | Wiring, voltage converter coolant temperature sensor | |
intermittent | ||
P0A05 | Voltage converter coolant pump control A – open circuit | Wiring, voltage converter coolant pump |
P0A06 | Voltage converter coolant pump control A – circuit low | Wiring, voltage converter coolant pump |
P0A07 | Voltage converter coolant pump control A – circuit high | Wiring, voltage converter coolant pump |
P0A08 | DC to DC converter status – circuit malfunction | – |
P0A09 | DC to DC converter status – circuit low | – |
P0A0A | High voltage system – interlock circuit malfunction | – |
P0A0B | High voltage system – interlock circuit performance | – |
P0A0C | High voltage system – interlock circuit low | – |
P0A0D | High voltage system – interlock circuit high | – |
P0A0E | High voltage system – interlock circuit intermittent | – |
P0A0F | Hybrid drive system – engine failed to start | – |
P0A10 | DC to DC converter status – circuit high | – |
P0A11 | DC to DC converter enable – circuit open | – |
P0A12 | DC to DC converter enable – circuit low | – |
P0A13 | DC to DC converter enable – circuit high | – |
P0A14 | Engine mounting control A – open circuit | – |
P0A15 | Engine mounting control A – circuit low | – |
P0A16 | Engine mounting control A – circuit high | – |
P0A17 | Motor torque sensor – circuit malfunction | Wiring, motor torque sensor |
P0A18 | Motor torque sensor – circuit range/performance | Wiring, motor torque sensor |
P0A19 | Motor torque sensor – circuit low | Wiring, motor torque sensor |
P0A1A | Generator control module | Wiring, Generator control module |
P0A1B | Drive motor A control module | Wiring, drive motor control module |
P0A1C | Drive motor B control module | Wiring, drive motor control module |
P0A1D | Hybrid powertrain control module | Wiring, hybrid powertrain control module |
P0A1E | Starter/generator control module | Wiring, starter/generator control module |
P0A1F | Battery energy control module | Wiring, battery energy control module |
P0A20 | Motor torque sensor – circuit high | Wiring, motor torque sensor |
P0A21 | Motor torque sensor – circuit intermittent | Wiring, motor torque sensor |
P0A22 | Generator torque sensor – circuit malfunction | Wiring, generator torque sensor |
P0A23 | Generator torque sensor – circuit range/performance | Wiring, generator torque sensor |
P0A24 | Generator torque sensor – circuit low | Wiring, generator torque sensor |
P0A25 | Generator torque sensor – circuit high | Wiring, generator torque sensor |
P0A26 | Generator torque sensor – circuit intermittent | Wiring, generator torque sensor |
P0A27 | Hybrid battery power off – circuit malfunction | – |
P0A28 | Hybrid battery power off – circuit low | – |
P0A29 | Hybrid battery power off – circuit high | – |
P0A2A | Drive motor A temperature sensor – circuit open | – |
P0A2B | Drive motor A temperature sensor – circuit range/performance | – |
P0A2C | Drive motor A temperature sensor – circuit low | – |
P0A2D | Drive motor A temperature sensor – circuit high | – |
P0A2E | Drive motor A temperature sensor – circuit intermittent | – |
Drive motor A temperature sensor – over-temperature | ||
P0A2F | – | |
condition | ||
P0A30 | Drive motor B temperature sensor – circuit open | – |
P0A31 | Drive motor B temperature sensor – circuit range/performance | – |
P0A32 | Drive motor B temperature sensor – circuit low | – |
P0A33 | Drive motor B temperature sensor – circuit high | – |
P0A34 | Drive motor B temperature sensor – circuit intermittent | – |
Drive motor B temperature sensor – over-temperature | ||
P0A35 | – | |
condition | ||
P0A36 | Generator temperature sensor – circuit malfunction | – |
P0A37 | Generator temperature sensor – circuit range/performance | – |
P0A38 | Generator temperature sensor – circuit low | – |
P0A39 | Generator temperature sensor – circuit high | – |
P0A3A | Generator temperature sensor – circuit intermittent | – |
P0A3B | Generator – over-temperature condition | – |
P0A3C | Drive motor A inverter – over-temperature condition | – |
P0A3D | Drive motor B inverter – over-temperature condition | – |
P0A3E | Generator inverter – over-temperature condition | – |
P0A3F | Drive motor A position sensor – circuit malfunction | |
P0A40 | Drive motor A position sensor – circuit range/performance | |
P0A41 | Drive motor A position sensor – circuit low | |
P0A42 | Drive motor A position sensor – circuit high | |
P0A43 | Drive motor A position sensor – circuit intermittent | |
P0A44 | Drive motor A position sensor – circuit over-speed | |
P0A45 | Drive motor B position sensor – circuit malfunction | |
P0A46 | Drive motor B position sensor – circuit range/performance | |
P0A47 | Drive motor B position sensor – circuit low | |
P0A48 | Drive motor B position sensor – circuit high | |
P0A49 | Drive motor B position sensor – circuit intermittent | |
P0A4A | Drive motor B position sensor – circuit over-speed | |
P0A4B | Generator position sensor – circuit malfunction | Wiring, generator position sensor |
P0A4C | Generator position sensor – circuit range/performance | Wiring, generator position sensor |
P0A4D | Generator position sensor – circuit low | Wiring, generator position sensor |
P0A4E | Generator position sensor – circuit high | Wiring, generator position sensor |
P0A4F | Generator position sensor – circuit intermittent | Wiring, generator position sensor |
P0A50 | Generator position sensor – circuit over-speed | Wiring, generator position sensor |
P0A51 | Drive motor A current sensor – circuit open | – |
P0A52 | Drive motor A current sensor – circuit range/performance | – |
P0A53 | Drive motor A current sensor – circuit low | – |
P0A54 | Drive motor A current sensor – circuit high | – |
P0A55 | Drive motor B current sensor – circuit malfunction | – |
P0A56 | Drive motor B current sensor – circuit range/performance | – |
P0A57 | Drive motor B current sensor – circuit low | – |
P0A58 | Drive motor B current sensor – circuit high | – |
P0A59 | Generator current sensor – circuit malfunction | Wiring, generator current sensor |
P0A5A | Generator current sensor – circuit range/performance | Wiring, generator current sensor |
P0A5B | Generator current sensor – circuit low | Wiring, generator current sensor |
P0A5C | Generator current sensor – circuit high | Wiring, generator current sensor |
P0A5D | Drive motor A – phase U current malfunction | – |
P0A5E | Drive motor A – phase U current low | – |
P0A5F | Drive motor A – phase U current high | – |
P0A60 | Drive motor A – phase V current malfunction | – |
P0A61 | Drive motor A – phase V current low | – |
P0A62 | Drive motor A – phase V current high | – |
P0A63 | Drive motor A – phase W current malfunction | – |
P0A64 | Drive motor A – phase W current low | – |
P0A65 | Drive motor A – phase W current high | – |
P0A66 | Drive motor B – phase U current malfunction | – |
P0A67 | Drive motor B – phase U current low | – |
P0A68 | Drive motor B – phase U current high | – |
P0A69 | Drive motor B – phase V current malfunction | – |
P0A6A | Drive motor B – phase V current low | – |
P0A6B | Drive motor B – phase V current high | – |
P0A6C | Drive motor B – phase W current malfunction | – |
P0A6D | Drive motor B – phase W current low | – |
P0A6E | Drive motor B – phase W current high | – |
P0A6F | Generator – phase U current malfunction | – |
P0A70 | Generator – phase U current low | – |
P0A71 | Generator – phase U current high | – |
P0A72 | Generator – phase V current malfunction | – |
P0A73 | Generator – phase V current low | – |
P0A74 | Generator – phase V current high | – |
P0A75 | Generator – phase W current malfunction | – |
P0A76 | Generator – phase W current low | – |
P0A77 | Generator – phase W current high | – |
P0A78 | Drive motor A inverter – performance problem | – |
P0A79 | Drive motor B inverter – performance problem | – |
P0A7A | Generator inverter – performance problem | – |
P0A7B | Battery energy control module – MIL activation requested | – |
P0A7C | Voltage converter – over-temperature condition | – |
P0A7D | Hybrid battery pack – battery discharged | – |
P0A7E | Hybrid battery pack – over-temperature condition | – |
P0A7F | Hybrid battery pack – deterioration | – |
P0A80 | Hybrid battery pack | Replace hybrid battery pack |
P0A81 | Hybrid battery pack cooling fan 1 – control circuit open | – |
P0A82 | Hybrid battery pack cooling fan 1 – performance or stuck off | – |
P0A83 | Hybrid battery pack cooling fan 1 – stuck on | – |
P0A84 | Hybrid battery pack cooling fan 1 – control circuit low | – |
P0A85 | Hybrid battery pack cooling fan 1 – control circuit high | – |
P0A86 | 14 volt power module current sensor – circuit malfunction | – |
14 volt power module current sensor – circuit | ||
P0A87 | – | |
range/performance | ||
P0A88 | 14 volt power module current sensor – circuit low | – |
P0A89 | 14 volt power module current sensor – circuit high | – |
P0A8A | 14 volt power module current sensor – circuit intermittent | – |
P0A8B | 14 volt power module – system voltage | – |
P0A8C | 14 volt power module – system voltage unstable | – |
P0A8D | 14 volt power module – system voltage low | – |
P0A8E | 14 volt power module – system voltage high | – |
P0A8F | 14 volt power module – system performance | – |
P0A90 | Drive motor A – performance problem | Wiring, drive motor |
P0A91 | Drive motor B – performance problem | Wiring, drive motor |
P0A92 | Hybrid generator – performance problem | – |
P0A93 | Inverter A – cooling system performance | – |
P0A94 | DC to DC converter – performance problem | – |
P0A95 | Hybrid battery pack – high voltage fuse | – |
P0A96 | Hybrid battery pack cooling fan 2 – control circuit open | – |
P0A97 | Hybrid battery pack cooling fan 2 – performance or stuck off | – |
P0A98 | Hybrid battery pack cooling fan 2 – stuck on | – |
P0A99 | Hybrid battery pack cooling fan 2 – control circuit low | – |
P0A9A | Hybrid battery pack cooling fan 2 – control circuit high | – |
P0A9B | Hybrid battery temperature sensor A – circuit | – |
Hybrid battery temperature sensor A – circuit | ||
P0A9C | – | |
range/performance | ||
P0A9D | Hybrid battery temperature sensor A – circuit low | – |
P0A9E | Hybrid battery temperature sensor A – circuit high | – |
Hybrid battery temperature sensor A – circuit | ||
P0A9F | – | |
intermittent/erratic | ||
P0AA0 | Hybrid battery positive contactor – circuit malfunction | – |
P0AA1 | Hybrid battery positive contactor – circuit stuck closed | – |
P0AA2 | Hybrid battery positive contactor – circuit stuck open | – |
P0AA3 | Hybrid battery positive contactor – circuit malfunction | – |
P0AA4 | Hybrid battery positive contactor – circuit stuck closed | – |
P0AA5 | Hybrid battery positive contactor – circuit stuck open | – |
P0AA6 | Hybrid battery voltage system – isolation fault | – |
P0AA7 | Hybrid battery voltage isolation sensor – circuit malfunction | – |
Hybrid battery voltage isolation sensor – circuit | ||
P0AA8 | – | |
range/performance | ||
P0AA9 | Hybrid battery voltage isolation sensor – circuit low | – |
P0AAA | Hybrid battery voltage isolation sensor – circuit high | – |
Hybrid battery voltage isolation sensor – circuit | ||
P0AAB | – | |
intermittent/erratic | ||
Hybrid battery pack air temperature sensor A – circuit | ||
P0AAC | – | |
malfunction | ||
Hybrid battery pack air temperature sensor A – circuit | ||
P0AAD | – | |
range/performance | ||
P0AAE | Hybrid battery pack air temperature sensor A – circuit low | – |
Hybrid battery pack air temperature sensor A – circuit | ||
P0AAF | – | |
malfunction | ||
Hybrid battery pack current sensor A – circuit | ||
P0AB0 | – | |
intermittent/erratic | ||
Hybrid battery pack air temperature sensor B – circuit | ||
P0AB1 | – | |
malfunction | ||
Hybrid battery pack air temperature sensor B – circuit | ||
P0AB2 | – | |
malfunction | ||
P0AB3 | Hybrid battery pack air temperature sensor B – circuit low | – |
P0AB4 | Hybrid battery pack air temperature sensor B – circuit high | – |
Hybrid battery pack air temperature sensor B – circuit | ||
P0AB5 | – | |
intermittent/erratic | ||
P0AB6 | Engine mounting control B – circuit open | – |
P0AB7 | Engine mounting control B – circuit low | – |
P0AB8 | Engine mounting control B – circuit high | – |
P0AB9 | Hybrid drive system – performance problem | – |
P0ABA | Hybrid battery pack voltage sensor A – circuit malfunction | – |
Hybrid battery pack voltage sensor A – circuit | ||
P0ABB | – | |
range/performance | ||
P0ABC | Hybrid battery pack voltage sensor A – circuit low | – |
P0ABD | Hybrid battery pack voltage sensor A – circuit high | – |
Hybrid battery pack voltage sensor A – circuit | ||
P0ABE | – | |
intermittent/erratic | ||
P0ABF | Hybrid battery pack current sensor A – circuit malfunction | – |
Hybrid battery pack current sensor A – circuit | ||
P0AC0 | – | |
range/performance | ||
P0AC1 | Hybrid battery pack current sensor A – circuit low | – |
P0AC2 | Hybrid battery pack current sensor A – circuit high | – |
Hybrid battery pack current sensor A – circuit | ||
P0AC3 | – | |
intermittent/erratic | ||
P0AC4 | Hybrid powertrain control module – MIL activation requested | – |
P0AC5 | Hybrid battery temperature sensor B – circuit malfunction | – |
Hybrid battery temperature sensor B – circuit | ||
P0AC6 | – | |
range/performance | ||
P0AC7 | Hybrid battery temperature sensor B – circuit low | – |
P0AC8 | Hybrid battery temperature sensor B – circuit high | – |
Hybrid battery temperature sensor B – circuit | ||
P0AC9 | – | |
intermittent/erratic | ||
P0ACA | Hybrid battery temperature sensor C – circuit malfunction | – |
Hybrid battery temperature sensor C – circuit | ||
P0ACB | – | |
range/performance | ||
P0ACC | Hybrid battery temperature sensor C – circuit low | – |
P0ACD | Hybrid battery temperature sensor C – circuit high | – |
Hybrid battery temperature sensor C – circuit | ||
P0ACE | – | |
intermittent/erratic | ||
P0ACF | Hybrid battery pack cooling fan 3 – control circuit open | – |
P0AD0 | Hybrid battery pack cooling fan 3 – performance or stuck off | – |
P0AD1 | Hybrid battery pack cooling fan 3 – stuck on | – |
P0AD2 | Hybrid battery pack cooling fan 3 – control circuit low | – |
P0AD3 | Hybrid battery pack cooling fan 3 – control circuit high | – |
P0AD4 | Hybrid battery pack cooling system – insufficient air flow | – |
P0AD5 | Hybrid battery pack air flow valve A – control circuit open | – |
Hybrid battery pack air flow valve A – circuit | ||
P0AD6 | – | |
range/performance | ||
P0AD7 | Hybrid battery pack air flow valve A – control circuit low | – |
P0AD8 | Hybrid battery pack air flow valve A – control circuit high | – |
P0AD9 | Hybrid battery positive contactor – control circuit open | – |
Hybrid battery positive contactor – control circuit | ||
P0ADA | – | |
range/performance | ||
P0ADB | Hybrid battery positive contactor – control circuit low | – |
P0ADC | Hybrid battery positive contactor – control circuit high | – |
P0ADD | Hybrid battery positive contactor – control circuit open | – |
Hybrid battery positive contactor – control circuit | ||
P0ADE | – | |
range/performance | ||
P0ADF | Hybrid battery positive contactor – control circuit low | – |
P0AE0 | Hybrid battery positive contactor – control circuit high | – |
P0AE1 | Hybrid battery precharge contactor – circuit malfunction | – |
P0AE2 | Hybrid battery precharge contactor – circuit stuck closed | – |
P0AE3 | Hybrid battery precharge contactor – circuit stuck open | – |
Hybrid battery precharge contactor – control circuit | ||
P0AE4 | – | |
malfunction | ||
Hybrid battery precharge contactor – circuit | ||
P0AE5 | – | |
range/performance | ||
P0AE6 | Hybrid battery precharge contactor – control circuit low | – |
P0AE7 | Hybrid battery precharge contactor – control circuit high | – |
P0AE8 | Hybrid battery temperature sensor D – circuit malfunction | – |
Hybrid battery temperature sensor D – circuit | ||
P0AE9 | – | |
range/performance | ||
P0AEA | Hybrid battery temperature sensor D – circuit low | – |
P0AEB | Hybrid battery temperature sensor D – circuit high | – |
Hybrid battery temperature sensor D – circuit | ||
P0AEC | – | |
intermittent/erratic | ||
Drive motor inverter temperature sensor A – circuit | ||
P0AED | – | |
malfunction | ||
Drive motor inverter temperature sensor A – circuit | ||
P0AEE | – | |
range/performance | ||
P0AEF | Drive motor inverter temperature sensor A – circuit low | – |
P0AF0 | Drive motor inverter temperature sensor A – circuit high | – |
Drive motor inverter temperature sensor A – circuit | ||
P0AF1 | – | |
intermittent/erratic | ||
Drive motor inverter temperature sensor B – circuit | ||
P0AF2 | – | |
malfunction | ||
Drive motor inverter temperature sensor B – circuit | ||
P0AF3 | – | |
range/performance | ||
P0AF4 | Drive motor inverter temperature sensor B – circuit low | |
P0AF5 | Drive motor inverter temperature sensor B – circuit high | – |
Drive motor inverter temperature sensor B – circuit | ||
P0AF6 | – | |
intermittent/erratic | ||
P0AF7 | 14 volt power module – internal temperature too high | – |
P0AF8 | Hybrid battery system – voltage malfunction | – |
P0AF9 | Hybrid battery system – system voltage unstable | – |
P0AFA | Hybrid battery system – voltage low | – |
P0AFB | Hybrid battery system – voltage high | – |
P0AFC | Hybrid battery pack sensor module | – |
P0AFD | Hybrid battery pack – battery temperature too low | – |
Hybrid battery system – voltage too low for voltage step up | ||
P0AFE | – | |
conversion | ||
Hybrid battery system – voltage too low for voltage step down | ||
P0AFF | – | |
conversion | ||
Auxiliary transmission fluid pump motor – phase U current | ||
P0B00 | – | |
malfunction | ||
P0B01 | Auxiliary transmission fluid pump motor – phase U current low | – |
Auxiliary transmission fluid pump motor – phase U current | ||
P0B02 | – | |
high | ||
Auxiliary transmission fluid pump motor – phase V current | ||
P0B03 | – | |
malfunction | ||
P0B04 | Auxiliary transmission fluid pump motor – phase V current low | – |
Auxiliary transmission fluid pump motor – phase V current | ||
P0B05 | – | |
high | ||
Auxiliary transmission fluid pump motor – phase W current | ||
P0B06 | – | |
malfunction | ||
P0B07 | Auxiliary transmission fluid pump motor – phase W current low | – |
Auxiliary transmission fluid pump motor – phase W current | ||
P0B08 | – | |
high | ||
Auxiliary transmission fluid pump motor – supply voltage | ||
P0B09 | – | |
circuit malfunction | ||
P0B0A | Auxiliary transmission fluid pump motor – supply voltage low | – |
P0B0B | Auxiliary transmission fluid pump motor – supply voltage high | |
P0B0C | Auxiliary transmission fluid pump – hydraulic leakage | – |
P0B0D | Auxiliary transmission fluid pump control module – malfunction | |
P0B0E | Hybrid battery pack current sensor B – circuit malfunction | – |
Hybrid battery pack current sensor B – circuit | ||
P0B0F | – | |
range/performance | ||
P0B10 | Hybrid battery pack current sensor B – circuit low | – |
P0B11 | Hybrid battery pack current sensor B – circuit high | – |
Hybrid battery pack current sensor B – circuit | ||
P0B12 | – | |
intermittent/erratic | ||
P0B13 | Hybrid battery pack current sensor – A/B correlation | – |
P0B14 | Hybrid battery pack voltage sensor B – circuit malfunction | – |
Hybrid battery pack voltage sensor B – circuit | ||
P0B15 | – | |
range/performance | ||
P0B16 | Hybrid battery pack voltage sensor B – circuit low | – |
P0B17 | Hybrid battery pack voltage sensor B – circuit high | – |
Hybrid battery pack voltage sensor B – circuit | ||
P0B18 | – | |
intermittent/erratic | ||
P0B19 | Hybrid battery pack voltage sensor C – circuit malfunction | – |
Hybrid battery pack voltage sensor C – circuit | ||
P0B1A | – | |
range/performance | ||
P0B1B | Hybrid battery pack voltage sensor C – circuit low | – |
P0B1C | Hybrid battery pack voltage sensor C – circuit high | – |
Hybrid battery pack voltage sensor C – circuit | ||
P0B1D | – | |
intermittent/erratic | ||
P0B1E | Hybrid battery pack voltage sensor D – circuit malfunction | – |
Hybrid battery pack voltage sensor D – circuit | ||
P0B1F | – | |
range/performance | ||
P0B20 | Hybrid battery pack voltage sensor D – circuit low | – |
P0B21 | Hybrid battery pack voltage sensor D – circuit high | – |
Hybrid battery pack voltage sensor D – circuit | ||
P0B22 | – | |
intermittent/erratic | ||
P0B23 | Hybrid battery A – voltage malfunction | – |
P0B24 | Hybrid battery A – voltage unstable | – |
P0B25 | Hybrid battery A – voltage low | – |
P0B26 | Hybrid battery A – voltage high | – |
P0B27 | Hybrid battery B – voltage malfunction | – |
P0B28 | Hybrid battery B – voltage unstable | – |
P0B29 | Hybrid battery B – voltage low | – |
P0B2A | Hybrid battery B – voltage high | – |
P0B2B | Hybrid battery C – voltage malfunction | – |
P0B2C | Hybrid battery C – voltage unstable | – |
P0B2D | Hybrid battery C – voltage low | – |
P0B2E | Hybrid battery C – voltage high | – |
P0B2F | Hybrid battery D – voltage malfunction | – |
P0B30 | Hybrid battery D – voltage unstable | – |
P0B31 | Hybrid battery D – voltage low | – |
P0B32 | Hybrid battery D – voltage high | – |
P0B33 | Hybrid battery pack isolator – circuit malfunction | – |
P0B34 | Hybrid battery pack isolator – circuit performance | – |
P0B35 | Hybrid battery pack isolator – circuit low | – |
P0B36 | Hybrid battery pack isolator – circuit high | – |
P0B37 | Hybrid battery pack isolator – circuit open | – |
P0B38 | Voltage converter coolant pump motor B – control circuit open | – |
P0B39 | Voltage converter coolant pump motor B – control circuit low | – |
P0B3A | Voltage converter coolant pump motor B – control circuit high | – |
P0B3B | Hybrid battery voltage sensor A – circuit malfunction | – |
P0B3C | Hybrid battery voltage sensor A – circuit range/performance | – |
P0B3D | Hybrid battery voltage sensor A – circuit low | – |
P0B3E | Hybrid battery voltage sensor A – circuit high | – |
P0B3F | Hybrid battery voltage sensor A – circuit intermittent/erratic | – |
P0B40 | Hybrid battery voltage sensor B – circuit malfunction | – |
P0B41 | Hybrid battery voltage sensor B – circuit range/performance | – |
P0B42 | Hybrid battery voltage sensor B – circuit low | – |
P0B43 | Hybrid battery voltage sensor B – circuit high | – |
P0B44 | Hybrid battery voltage sensor B – circuit intermittent/erratic | – |
P0B45 | Hybrid battery voltage sensor C – circuit malfunction | – |
P0B46 | Hybrid battery voltage sensor C – circuit range/performance | – |
P0B47 | Hybrid battery voltage sensor C – circuit low | – |
P0B48 | Hybrid battery voltage sensor C – circuit high | – |
P0B49 | Hybrid battery voltage sensor C – circuit intermittent/erratic | – |
P0B4A | Hybrid battery voltage sensor D – circuit malfunction | – |
P0B4B | Hybrid battery voltage sensor D – circuit range/performance | – |
P0B4C | Hybrid battery voltage sensor D – circuit low | – |
P0B4D | Hybrid battery voltage sensor D – circuit high | – |
P0B4E | Hybrid battery voltage sensor D – circuit intermittent/erratic | – |
P0B4F | Hybrid battery voltage sensor E – circuit malfunction | – |
P0B50 | Hybrid battery voltage sensor E – circuit range/performance | – |
P0B51 | Hybrid battery voltage sensor E – circuit low | – |
P0B52 | Hybrid battery voltage sensor E – circuit high | – |
P0B53 | Hybrid battery voltage sensor E – circuit intermittent/erratic | – |
P0B54 | Hybrid battery voltage sensor F – circuit malfunction | – |
P0B55 | Hybrid battery voltage sensor F – circuit range/performance | – |
P0B56 | Hybrid battery voltage sensor F – circuit low | – |
P0B57 | Hybrid battery voltage sensor F – circuit high | – |
P0B58 | Hybrid battery voltage sensor F – circuit intermittent/erratic | – |
P0B59 | Hybrid battery voltage sensor G – circuit malfunction | – |
P0B5A | Hybrid battery voltage sensor G – circuit range/performance | – |
P0B5B | Hybrid battery voltage sensor G – circuit low | – |
P0B5C | Hybrid battery voltage sensor G – circuit high | – |
P0B5D | Hybrid battery voltage sensor G – circuit intermittent/erratic | – |
P0B5E | Hybrid battery voltage sensor H – circuit malfunction | – |
P0B5F | Hybrid battery voltage sensor H – circuit range/performance | – |
P0B60 | Hybrid battery voltage sensor H – circuit low | – |
P0B61 | Hybrid battery voltage sensor H – circuit high | – |
P0B62 | Hybrid battery voltage sensor H – circuit intermittent/erratic | – |
P0B63 | Hybrid battery voltage sensor I – circuit malfunction | – |
P0B64 | Hybrid battery voltage sensor I – circuit range/performance | – |
P0B65 | Hybrid battery voltage sensor I – circuit low | – |
P0B66 | Hybrid battery voltage sensor I – circuit high | – |
P0B67 | Hybrid battery voltage sensor I – circuit intermittent/erratic | – |
P0B68 | Hybrid battery voltage sensor J – circuit malfunction | – |
P0B69 | Hybrid battery voltage sensor J – circuit range/performance | – |
P0B6A | Hybrid battery voltage sensor J – circuit low | – |
P0B6B | Hybrid battery voltage sensor J – circuit high | – |
P0B6C | Hybrid battery voltage sensor J – circuit intermittent/erratic | – |
P0B6D | Hybrid battery voltage sensor K – circuit malfunction | – |
P0B6E | Hybrid battery voltage sensor K – circuit range/performance | – |
P0B6F | Hybrid battery voltage sensor K – circuit low | – |
P0B70 | Hybrid battery voltage sensor K – circuit high | – |
P0B71 | Hybrid battery voltage sensor K – circuit intermittent/erratic | – |
P0B72 | Hybrid battery voltage sensor L – circuit malfunction | – |
P0B73 | Hybrid battery voltage sensor L – circuit range/performance | – |
P0B74 | Hybrid battery voltage sensor L – circuit low | – |
P0B75 | Hybrid battery voltage sensor L – circuit high | – |
P0B76 | Hybrid battery voltage sensor L – circuit intermittent/erratic | – |
P0B77 | Hybrid battery voltage sensor M – circuit malfunction | – |
P0B78 | Hybrid battery voltage sensor M – circuit range/performance | – |
P0B79 | Hybrid battery voltage sensor M – circuit low | – |
P0B7A | Hybrid battery voltage sensor M – circuit high | – |
P0B7B | Hybrid battery voltage sensor M – circuit intermittent/erratic | – |
P0B7C | Hybrid battery voltage sensor N – circuit malfunction | – |
P0B7D | Hybrid battery voltage sensor N – circuit range/performance | – |
P0B7E | Hybrid battery voltage sensor N – circuit low | – |
P0B7F | Hybrid battery voltage sensor N – circuit high | – |
P0B80 | Hybrid battery voltage sensor N – circuit intermittent/erratic | – |
P0B81 | Hybrid battery voltage sensor O – circuit malfunction | – |
P0B82 | Hybrid battery voltage sensor O – circuit range/performance | – |
P0B83 | Hybrid battery voltage sensor O – circuit low | – |
P0B84 | Hybrid battery voltage sensor O – circuit high | – |
P0B85 | Hybrid battery voltage sensor O – circuit intermittent/erratic | – |
P0B86 | Hybrid battery voltage sensor P – circuit malfunction | – |
P0B87 | Hybrid battery voltage sensor P – circuit range/performance | – |
P0B88 | Hybrid battery voltage sensor P – circuit low | – |
P0B89 | Hybrid battery voltage sensor P – circuit high | – |
P0B8A | Hybrid battery voltage sensor P – circuit intermittent/erratic | – |
P0B8B | Hybrid battery voltage sensor Q – circuit malfunction | – |
P0B8C | Hybrid battery voltage sensor Q – circuit range/performance | – |
P0B8D | Hybrid battery voltage sensor Q – circuit low | – |
P0B8E | Hybrid battery voltage sensor Q – circuit high | – |
P0B8F | Hybrid battery voltage sensor Q – circuit intermittent/erratic | – |
P0B90 | Hybrid battery voltage sensor R – circuit malfunction | – |
P0B91 | Hybrid battery voltage sensor R – circuit range/performance | – |
P0B92 | Hybrid battery voltage sensor R – circuit low | – |
P0B93 | Hybrid battery voltage sensor R – circuit high | – |
P0B94 | Hybrid battery voltage sensor R – circuit intermittent/erratic | – |
P0B95 | Hybrid battery voltage sensor S – circuit malfunction | – |
P0B96 | Hybrid battery voltage sensor S – circuit range/performance | – |
P0B97 | Hybrid battery voltage sensor S – circuit low | – |
P0B98 | Hybrid battery voltage sensor S – circuit high | – |
P0B99 | Hybrid battery voltage sensor S – circuit intermittent/erratic | – |
P0B9A | Hybrid battery voltage sensor T – circuit | – |
P0B9B | Hybrid battery voltage sensor T – circuit range/performance | – |
P0B9C | Hybrid battery voltage sensor T – circuit low | – |
P0B9D | Hybrid battery voltage sensor T – circuit high | – |
P0B9E | Hybrid battery voltage sensor T – circuit intermittent/erratic | – |
P0B9F | Hybrid battery voltage sensor U – circuit malfunction | – |
P0BA0 | Hybrid battery voltage sensor U – circuit range/performance | – |
P0BA1 | Hybrid battery voltage sensor U – circuit low | – |
P0BA2 | Hybrid battery voltage sensor U – circuit high | – |
P0BA3 | Hybrid battery voltage sensor U – circuit intermittent/erratic | – |
P0BA4 | Hybrid battery voltage sensor V – circuit malfunction | – |
P0BA5 | Hybrid battery voltage sensor V – circuit range/performance | – |
P0BA6 | Hybrid battery voltage sensor V – circuit low | – |
P0BA7 | Hybrid battery voltage sensor V – circuit high | – |
P0BA8 | Hybrid battery voltage sensor V – circuit intermittent/erratic | – |
P0BA9 | Hybrid battery voltage sensor W – circuit malfunction | – |
P0BAA | Hybrid battery voltage sensor W – circuit range/performance | – |
P0BAA | Hybrid battery voltage sensor W – circuit range/performance | – |
P0BAB | Hybrid battery voltage sensor W – circuit low | – |
P0BAB | Hybrid battery voltage sensor W – circuit low | – |
P0BAC | Hybrid battery voltage sensor W – circuit high | – |
P0BAC | Hybrid battery voltage sensor W – circuit high | – |
P0BAD | Hybrid battery voltage sensor W – circuit intermittent/erratic | – |
P0BAD | Hybrid battery voltage sensor W – circuit intermittent/erratic | – |
P0BAE | Hybrid battery voltage sensor X – circuit malfunction | – |
P0BAE | Hybrid battery voltage sensor X – circuit malfunction | – |
P0BAF | Hybrid battery voltage sensor X – circuit range/performance | – |
P0BAF | Hybrid battery voltage sensor X – circuit range/performance | – |
P0BB0 | Hybrid battery voltage sensor X – circuit low | – |
P0BB0 | Hybrid battery voltage sensor X – circuit low | – |
P0BB1 | Hybrid battery voltage sensor X – circuit high | – |
P0BB2 | Hybrid battery voltage sensor X – circuit intermittent/erratic | – |
P0BB3 | Hybrid battery voltage sensor Y – circuit | – |
P0BB4 | Hybrid battery voltage sensor Y – circuit range/performance | – |
P0BB5 | Hybrid battery voltage sensor Y – circuit low | – |
P0BB6 | Hybrid battery voltage sensor Y – circuit high | – |
P0BB7 | Hybrid battery voltage sensor Y – circuit intermittent/erratic | – |
P0BB8 | Hybrid battery voltage sensor Z – circuit | – |
P0BB9 | Hybrid battery voltage sensor Z – circuit range/performance | – |
P0BBA | Hybrid battery voltage sensor Z – circuit low | – |
P0BBB | Hybrid battery voltage sensor Z – circuit high | – |
P0BBC | Hybrid battery voltage sensor Z – circuit intermittent/erratic | – |
P0BBD | Hybrid battery pack – voltage variation limit exceeded | – |
P0BBE | Hybrid battery pack – voltage variation | – |
Hybrid battery pack cooling fan – supply voltage circuit | ||
P0BBF | – | |
malfunction | ||
P0BC0 | Hybrid battery pack cooling fan – supply voltage low | – |
P0BC1 | Hybrid battery pack cooling fan – supply voltage high | – |
P0BC2 | Hybrid battery temperature sensor E – circuit malfunction | – |
Hybrid battery temperature sensor E – circuit | ||
P0BC3 | – | |
range/performance | ||
P0BC4 | Hybrid battery temperature sensor E – circuit low | – |
P0BC5 | Hybrid battery temperature sensor E – circuit high | – |
Hybrid battery temperature sensor E – circuit | ||
P0BC6 | – | |
intermittent/erratic | ||
P0BC7 | Hybrid battery pack cooling fan sensor – circuit open | – |
Hybrid battery pack cooling fan sensor – circuit | ||
P0BC8 | – | |
range/performance | ||
P0BC9 | Hybrid battery pack cooling fan sensor – circuit low | – |
P0BCA | Hybrid battery pack cooling fan sensor – circuit high | – |
Hybrid battery pack cooling fan sensor – circuit | ||
P0BCB | – | |
intermittent/erratic | ||
P0BCC | Generator temperature sensor – circuit malfunction | – |
Generator inverter temperature sensor – circuit | ||
P0BCD | – | |
range/performance | ||
P0BCE | Generator inverter temperature sensor – circuit low | – |
P0BCF | Generator temperature sensor – circuit high | – |
Generator inverter temperature sensor – circuit | ||
P0BD0 | – | |
intermittent/erratic | ||
Drive motor inverter temperature sensor C – circuit | ||
P0BD1 | – | |
malfunction | ||
Drive motor inverter temperature sensor C – circuit | ||
P0BD2 | – | |
range/performance | ||
P0BD3 | Drive motor inverter temperature sensor C – circuit low | – |
P0BD4 | Drive motor inverter temperature sensor C – circuit high | – |
Drive motor inverter temperature sensor C – circuit | ||
P0BD5 | – | |
intermittent/erratic | ||
P0BD6 | Drive motor inverter temperature sensor D – circuit | – |
Drive motor inverter temperature sensor D – circuit | ||
P0BD7 | – | |
range/performance | ||
P0BD8 | Drive motor inverter temperature sensor D – circuit low | – |
P0BD9 | Drive motor inverter temperature sensor D – circuit high | – |
Drive motor inverter temperature sensor D – circuit | ||
P0BDA | Wiring, drive motor inverter temperature sensor | |
intermittent/erratic | ||
Drive motor inverter temperature sensor E – circuit | ||
P0BDB | Wiring, drive motor inverter temperature sensor | |
malfunction | ||
Drive motor inverter temperature sensor E – circuit | ||
P0BDC | Wiring, drive motor inverter temperature sensor | |
range/performance | ||
P0BDD | Drive motor inverter temperature sensor E – circuit low | Wiring, drive motor inverter temperature sensor |
P0BDE | Drive motor inverter temperature sensor E – circuit high | Wiring, drive motor inverter temperature sensor |
Drive motor inverter temperature sensor E – circuit | ||
P0BDF | Wiring, drive motor inverter temperature sensor | |
intermittent/erratic | ||
Drive motor inverter temperature sensor F – circuit | ||
P0BE0 | Wiring, drive motor inverter temperature sensor | |
malfunction | ||
Drive motor inverter temperature sensor F – circuit | ||
P0BE1 | – | |
range/performance | ||
P0BE2 | Drive motor inverter temperature sensor F – circuit low | – |
P0BE3 | Drive motor inverter temperature sensor F – circuit high | – |
Drive motor inverter temperature sensor F – circuit | ||
P0BE4 | – | |
intermittent/erratic | ||
P0BE5 | Drive motor A, phase U current sensor – circuit malfunction | – |
Drive motor A, phase U current sensor – circuit | ||
P0BE6 | – | |
range/performance | ||
P0BE7 | Drive motor A, phase U current sensor – circuit low | – |
P0BE8 | Drive motor A, phase U current sensor – circuit high | – |
P0BE9 | Drive motor A, phase V current sensor – circuit malfunction | – |
Drive motor A, phase V current sensor – circuit | ||
P0BEA | Wiring, drive motor current sensor | |
range/performance | ||
P0BEB | Drive motor A, phase V current sensor – circuit low | Wiring, drive motor current sensor |
P0BEC | Drive motor A, phase V current sensor – circuit high | Wiring, drive motor current sensor |
P0BED | Drive motor A, phase W current sensor – circuit malfunction | Wiring, drive motor current sensor |
Drive motor A, phase W current sensor – circuit | ||
P0BEE | Wiring, drive motor current sensor | |
range/performance | ||
P0BEF | Drive motor A, phase W current sensor – circuit low | Wiring, drive motor current sensor |
P0BF0 | Drive motor A, phase W current sensor – circuit high | Wiring, drive motor current sensor |
P0BF1 | Drive motor B, phase U current sensor – circuit malfunction | – |
Drive motor B, phase U current sensor – circuit | ||
P0BF2 | – | |
range/performance | ||
P0BF3 | Drive motor B, phase U current sensor – circuit low | – |
P0BF4 | Drive motor B, phase U current sensor – circuit high | – |
P0BF5 | Drive motor B, phase V current sensor – circuit malfunction | – |
Drive motor B, phase V current sensor – circuit | ||
P0BF6 | – | |
range/performance | ||
P0BF7 | Drive motor B, phase V current sensor – circuit low | – |
P0BF8 | Drive motor B, phase V current sensor – circuit high | – |
P0BF9 | Drive motor B, phase W current sensor – circuit malfunction | – |
Drive motor B, phase W current sensor – circuit | ||
P0BFA | Wiring, drive motor current sensor | |
range/performance | ||
P0BFB | Drive motor B, phase W current sensor – circuit low | Wiring, drive motor current sensor |
P0BFC | Drive motor B, phase W current sensor – circuit high | Wiring, drive motor current sensor |
Drive motor A, phase U/V/W current sensor – correlation | ||
P0BFD | Wiring, drive motor current sensor | |
malfunction | ||
Drive motor B, phase U/V/W current sensor – correlation | ||
P0BFE | Wiring, drive motor current sensor | |
malfunction | ||
P0BFF | Drive motor A – current malfunction | Wiring, drive motor |
P0C00 | Drive motor A – current low | – |
P0C01 | Drive motor A – current high | – |
P0C02 | Drive motor B – current | – |
P0C03 | Drive motor B – current low | – |
P0C04 | Drive motor B – current high | – |
P0C05 | Drive motor A, phase U/V/W circuit – circuit open | – |
P0C06 | Drive motor A, phase U/V/W circuit – circuit low | – |
P0C07 | Drive motor A, phase U/V/W circuit – circuit high | – |
P0C08 | Drive motor B, phase U/V/W circuit – circuit open | – |
P0C09 | Drive motor B, phase U/V/W circuit – circuit low | – |
P0C0A | Drive motor B, phase U/V/W circuit – circuit high | – |
P0C0B | Drive motor A inverter – supply voltage circuit malfunction | – |
P0C0C | Drive motor A inverter – power supply low | – |
P0C0D | Drive motor A inverter – power supply high | – |
P0C0E | Drive motor B inverter – supply voltage circuit malfunction | – |
P0C0F | Drive motor B inverter – power supply low | – |
P0C10 | Drive motor B inverter – power supply high | – |
Drive motor A inverter, phase U circuit – over-temperature | ||
P0C11 | – | |
condition | ||
Drive motor A inverter, phase V circuit – over-temperature | ||
P0C12 | – | |
condition | ||
Drive motor A inverter, phase W circuit – over-temperature | ||
P0C13 | – | |
condition | ||
Drive motor B inverter, phase U circuit – over-temperature | ||
P0C14 | – | |
condition | ||
Drive motor B inverter, phase V circuit – over-temperature | ||
P0C15 | – | |
condition | ||
Drive motor B inverter, phase W circuit – over-temperature | ||
P0C16 | – | |
condition | ||
P0C17 | Drive motor A position sensor – calibration not learned | – |
P0C18 | Drive motor B position sensor – calibration not learned | – |
P0C19 | Drive motor A – torque delivered performance | – |
P0C1A | Drive motor B – torque delivered performance | – |
Auxiliary transmission fluid pump control module – internal | ||
P0C1B | – | |
temperature too high | ||
Auxiliary transmission fluid pump control module, internal | ||
P0C1C | – | |
temperature sensor – circuit malfunction | ||
Auxiliary transmission fluid pump control module, internal | ||
P0C1D | – | |
temperature sensor – circuit range/performance | ||
Auxiliary transmission fluid pump control module, internal | ||
P0C1E | – | |
temperature sensor – circuit low | ||
Auxiliary transmission fluid pump control module, internal | ||
P0C1F | – | |
temperature sensor – circuit high | ||
Auxiliary transmission fluid pump, phase U/V/W circuit – open | ||
P0C20 | – | |
circuit | ||
Auxiliary transmission fluid pump, phase U/V/W circuit – | ||
P0C21 | – | |
circuit low | ||
Auxiliary transmission fluid pump, phase U/V/W circuit – | ||
P0C22 | – | |
circuit high | ||
P0C23 | Auxiliary transmission fluid pump control module – open circuit | – |
P0C24 | Auxiliary transmission fluid pump control module – circuit low | – |
P0C25 | Auxiliary transmission fluid pump control module – circuit high | – |
P0C26 | Auxiliary transmission fluid pump motor – no current | – |
P0C27 | Auxiliary transmission fluid pump motor – current low | – |
P0C28 | Auxiliary transmission fluid pump motor – current high | – |
Auxiliary transmission fluid pump, driver circuit – circuit | ||
P0C29 | – | |
malfunction | ||
P0C2A | Auxiliary transmission fluid pump motor – pump motor stalled | – |
Auxiliary transmission fluid pump control module – feedback | ||
P0C2B | – | |
circuit malfunction | ||
Auxiliary transmission fluid pump control module – feedback | ||
P0C2C | – | |
signal range/performance | ||
Auxiliary transmission fluid pump control module – feedback | ||
P0C2D | – | |
signal low | ||
Auxiliary transmission fluid pump control module – feedback | ||
P0C2E | – | |
signal high | ||
Internal control module, drive motor/generator, engine speed | ||
P0C2F | – | |
(RPM) sensor – performance problem | ||
P0C30 | Hybrid battery pack – state of charge high | – |
P0C31 | Inverter B cooling system – performance problem | – |
P0C32 | Hybrid battery pack cooling system – performance problem | – |
P0C33 | Hybrid battery temperature sensor F – circuit malfunction | – |
Hybrid battery temperature sensor F – circuit | ||
P0C34 | – | |
range/performance | ||
P0C35 | Hybrid battery temperature sensor F – circuit low | – |
P0C36 | Hybrid battery temperature sensor F – circuit high | – |
Hybrid battery temperature sensor F – circuit | ||
P0C37 | ||
intermittent/erratic | ||
DC to DC converter temperature sensor A – circuit | ||
P0C38 | – | |
malfunction | ||
DC to DC converter temperature sensor A – circuit | ||
P0C39 | – | |
range/performance | ||
P0C3A | DC to DC converter temperature sensor A – circuit low | – |
P0C3B | DC to DC converter temperature sensor A – circuit high | – |
DC to DC converter temperature sensor A – circuit | ||
P0C3C | – | |
intermittent/erratic | ||
DC to DC converter temperature sensor B – circuit | ||
P0C3D | – | |
malfunction | ||
DC to DC converter temperature sensor B – circuit | ||
P0C3E | – | |
range/performance | ||
P0C3F | DC to DC converter temperature sensor B – circuit low | – |
P0C40 | DC to DC converter temperature sensor B – circuit high | – |
DC to DC converter temperature sensor B – circuit | ||
P0C41 | – | |
intermittent/erratic | ||
Hybrid battery pack coolant temperature sensor – circuit | ||
P0C42 | – | |
malfunction | ||
Hybrid battery pack coolant temperature sensor – circuit | ||
P0C43 | – | |
range/performance | ||
P0C44 | Hybrid battery pack coolant temperature sensor – circuit low | – |
P0C45 | Hybrid battery pack coolant temperature sensor – circuit high | – |
Hybrid battery pack coolant temperature sensor – circuit | ||
P0C46 | – | |
intermittent/erratic | ||
P0C47 | Hybrid battery pack coolant pump control – open circuit | – |
P0C48 | Hybrid battery pack coolant pump control – circuit low | – |
P0C49 | Hybrid battery pack coolant pump control – circuit high | – |
Hybrid battery pack coolant pump control – performance | ||
P0C4A | – | |
problem | ||
P0C4B | Hybrid battery pack coolant pump – no supply voltage | – |
P0C4C | Hybrid battery pack coolant pump – supply voltage low | – |
P0C4D | Hybrid battery pack coolant pump – supply voltage high | – |
P0C4E | Drive motor A – position learning limit exceeded | – |
P0C4F | Drive motor B – position learning limit exceeded | – |
P0C50 | Drive motor A position sensor, circuit A – circuit malfunction | Wiring, drive motor position sensor |
Drive motor A position sensor, circuit A – circuit | ||
P0C51 | Wiring, drive motor position sensor | |
range/performance | ||
P0C52 | Drive motor A position sensor, circuit A – circuit low | Wiring, drive motor position sensor |
P0C53 | Drive motor A position sensor, circuit A – circuit high | Wiring, drive motor position sensor |
Drive motor A position sensor, circuit A – circuit | ||
P0C54 | Wiring, drive motor position sensor | |
intermittent/erratic | ||
P0C55 | Drive motor B position sensor, circuit A – circuit malfunction | Wiring, drive motor position sensor |
Drive motor B position sensor, circuit A – circuit | ||
P0C56 | Wiring, drive motor position sensor | |
range/performance | ||
P0C57 | Drive motor B position sensor, circuit A – circuit low | Wiring, drive motor position sensor |
P0C58 | Drive motor B position sensor, circuit A – circuit high | Wiring, drive motor position sensor |
Drive motor B position sensor, circuit A – circuit | ||
P0C59 | Wiring, drive motor position sensor | |
intermittent/erratic | ||
P0C5A | Drive motor A position sensor, circuit B – circuit malfunction | Wiring, drive motor position sensor |
Drive motor A position sensor, circuit B – circuit | ||
P0C5B | Wiring, drive motor position sensor | |
range/performance | ||
P0C5C | Drive motor A position sensor, circuit B – circuit low | Wiring, drive motor position sensor |
P0C5D | Drive motor A position sensor, circuit B – circuit high | Wiring, drive motor position sensor |
Drive motor A position sensor, circuit B – circuit | ||
P0C5E | Wiring, drive motor position sensor | |
intermittent/erratic | ||
P0C5F | Drive motor B position sensor, circuit B – circuit malfunction | Wiring, drive motor position sensor |
Drive motor B position sensor, circuit B – circuit | ||
P0C60 | Wiring, drive motor position sensor | |
range/performance | ||
P0C61 | Drive motor B position sensor, circuit B – circuit low | Wiring, drive motor position sensor |
P0C62 | Drive motor B position sensor, circuit B – circuit high | Wiring, drive motor position sensor |
Drive motor B position sensor, circuit B – circuit | ||
P0C63 | Wiring, drive motor position sensor | |
intermittent/erratic | ||
P0C64 | Generator position sensor, circuit A – circuit malfunction | – |
Generator position sensor, circuit A – circuit | ||
P0C65 | – | |
range/performance | ||
P0C66 | Generator position sensor, circuit A – circuit low | – |
P0C67 | Generator position sensor, circuit A – circuit high | – |
Generator position sensor, circuit A – circuit | ||
P0C68 | – | |
intermittent/erratic | ||
P0C69 | Generator position sensor, circuit B – circuit malfunction | – |
Generator position sensor, circuit B – circuit | ||
P0C6A | – | |
range/performance | ||
P0C6B | Generator position sensor, circuit B – circuit low | – |
P0C6C | Generator position sensor, circuit B – circuit high | – |
Generator position sensor, circuit B – circuit | ||
P0C6D | – | |
intermittent/erratic | ||
P0C6E | Hybrid battery temperature sensor – A/B correlation | – |
P0C6F | Hybrid battery temperature sensor – B/C correlation | – |
P0C70 | Hybrid battery temperature sensor – C/D correlation | – |
P0C71 | Hybrid battery temperature sensor – D/E correlation | – |
P0C72 | Hybrid battery temperature sensor – E/F correlation | – |
Voltage converter coolant pump motor A control – | ||
P0C73 | – | |
performance problem | ||
Voltage converter coolant pump motor B control – | ||
P0C74 | – | |
performance problem | ||
P0C75 | Hybrid battery system – discharge time too short | – |
P0C76 | Hybrid battery system – discharge time too long | – |
P0C77 | Hybrid battery system – precharge time too short | – |
P0C78 | Hybrid battery system – precharge time too long | – |
P0C79 | Drive motor A inverter – voltage too high | – |
P0C7A | Drive motor B inverter – voltage too high | – |
P0C7B | Generator inverter – voltage too high | – |
P0C7C | Hybrid battery temperature sensor G – circuit malfunction | – |
Hybrid battery temperature sensor G – circuit | ||
P0C7D | – | |
range/performance | ||
P0C7E | Hybrid battery temperature sensor G – circuit low | – |
P0C7F | Hybrid battery temperature sensor G – circuit high | – |
Hybrid battery temperature sensor G – circuit | ||
P0C80 | – | |
intermittent/erratic | ||
P0C81 | Hybrid battery temperature sensor H – circuit malfunction | – |
Hybrid battery temperature sensor H – circuit | ||
P0C82 | – | |
range/performance | ||
P0C83 | Hybrid battery temperature sensor H – circuit low | – |
P0C84 | Hybrid battery temperature sensor H – circuit high | – |
Hybrid battery temperature sensor H – circuit | ||
P0C85 | – | |
intermittent/erratic | ||
P0C86 | Hybrid battery temperature sensor – F/G correlation | – |
P0C87 | Hybrid battery temperature sensor – G/H correlation | – |
P0C88 | Hybrid battery temperature sensor I – circuit malfunction | – |
Hybrid battery temperature sensor I – circuit | ||
P0C89 | – | |
range/performance | ||
P0C8A | Hybrid battery temperature sensor I – circuit low | – |
P0C8B | Hybrid battery temperature sensor I – circuit high | – |
Hybrid battery temperature sensor I – circuit | ||
P0C8C | – | |
intermittent/erratic | ||
P0C8D | Hybrid battery temperature sensor J – circuit malfunction | – |
Hybrid battery temperature sensor J – circuit | ||
P0C8E | – | |
range/performance | ||
P0C8F | Hybrid battery temperature sensor J – circuit low | – |
P0C90 | Hybrid battery temperature sensor J – circuit high | – |
Hybrid battery temperature sensor J – circuit | ||
P0C91 | – | |
intermittent/erratic | ||
P0C92 | Hybrid battery temperature sensor K – circuit malfunction | – |
Hybrid battery temperature sensor K – circuit | ||
P0C93 | – | |
range/performance | ||
P0C94 | Hybrid battery temperature sensor K – circuit low | – |
P0C95 | Hybrid battery temperature sensor K – circuit high | – |
Hybrid battery temperature sensor K – circuit | ||
P0C96 | – | |
intermittent/erratic | ||
P0C97 | Hybrid battery temperature sensor L – circuit malfunction | – |
Hybrid battery temperature sensor L – circuit | ||
P0C98 | – | |
range/performance | ||
P0C99 | Hybrid battery temperature sensor L – circuit low | – |
P0C9A | Hybrid battery temperature sensor L – circuit high | – |
Hybrid battery temperature sensor L – circuit | ||
P0C9B | – | |
intermittent/erratic | ||
P0C9C | 14 volt power module current sensor B – circuit malfunction | – |
14 volt power module current sensor B – circuit | ||
P0C9D | – | |
range/performance | ||
P0C9E | 14 volt power module current sensor B – circuit low | – |
P0C9F | 14 volt power module current sensor B – circuit high | – |
P0CA0 | 14 volt power module current sensor B – circuit intermittent | – |
P0CA1 | Drive motor control module – MIL activation requested | – |
DC to DC converter, step down voltage – performance | ||
P0CA2 | – | |
problem | ||
P0CA3 | DC to DC converter, step up voltage – performance problem | – |
P0CA4 | Hybrid battery system – charging voltage too high | – |
P0CA5 | Hybrid battery system – discharging voltage too high | – |
P0CA6 | Hybrid battery system – charging current too high | – |
P0CA7 | Hybrid battery system – discharging current too high | – |
P0CA8 | Hybrid battery temperature sensor M – circuit malfunction | – |
Hybrid battery temperature sensor M – circuit | ||
P0CA9 | – | |
range/performance | ||
P0CAA | Hybrid battery temperature sensor M – circuit low | – |
P0CAB | Hybrid battery temperature sensor M – circuit high | – |
Hybrid battery temperature sensor M – circuit | ||
P0CAC | – | |
intermittent/erratic | ||
P0CAD | Hybrid battery temperature sensor N – circuit malfunction | – |
Hybrid battery temperature sensor N – circuit | ||
P0CAE | – | |
range/performance | ||
P0CAF | Hybrid battery temperature sensor N – circuit low | – |
P0CB0 | Hybrid battery temperature sensor N – circuit high | – |
Hybrid battery temperature sensor N – circuit | ||
P0CB1 | – | |
intermittent/erratic | ||
P0CB2 | Hybrid battery temperature sensor O – circuit malfunction | – |
Hybrid battery temperature sensor O – circuit | ||
P0CB3 | – | |
range/performance | ||
P0CB4 | Hybrid battery temperature sensor O – circuit low | – |
P0CB5 | Hybrid battery temperature sensor O – circuit high | – |
Hybrid battery temperature sensor O – circuit | ||
P0CB6 | – | |
intermittent/erratic | ||
P0CB7 | Hybrid battery temperature sensor P – circuit malfunction | – |
Hybrid battery temperature sensor P – circuit | ||
P0CB8 | – | |
range/performance | ||
P0CB9 | Hybrid battery temperature sensor P – circuit low | – |
P0CBA | Hybrid battery temperature sensor P – circuit high | – |
Hybrid battery temperature sensor P – circuit | ||
P0CBB | – | |
intermittent/erratic |