HOW TO GUIDE: Ford F-Series RKE Keyfob Programming

1. Enter Programming Mode – Step 1

   INSERT key into ignition and TURN from OFF to RUN/ACC.

   OFF is the position where you can remove your key, RUN/ACC is the position just shy of starting your vehicle.

2. Enter Programming Mode – Step 2

   LOCATE the Programming Connector located at the base of the Steering Wheel Column.

   The Programming Connector consists of 2 wires and a plastic plug terminator with 2 pins.

   The pins will NOT be connected to anything.

3. Enter Programming Mode – Step 3

   JUMP the 2 pins in the Programming Connector using a suitable metal jumping wire (example – paperclip).
4. Program Remote

   PRESS any button on the remote to be programmed.

   Door locks will cycle Lock/Unlock to confirm successful programming of the remote.

   REPEAT this step IMMEDIATELY for any other remotes to be programmed to your vehicle.

5. Exit Programming Mode

   TURN ignition to OFF to exit Programming Mode.

   The vehicle locks will cycle Lock/Unlock to indicate successful completion of programming.

6. Test Remotes

   Test all remotes. Programming is now complete.

1. Preparatory Steps

   Do NOT DEPRESS the brake pedal during this procedure.

   CLOSE and UNLOCK all doors using the power door locks.

2. Enter Vehicle Programming Mode

   INSERT key into Ignition and TURN from OFF to RUN 8 times within 10 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm Programming Mode.

3. Program Remote

   Within 20 seconds press any button on first keyless remote fob. Door locks will cycle to confirm programming.

   (Repeat immediately for any additional remotes to be programmed.)

4. Exit Programming Mode

   Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.

5. Test Remotes

   Test all remotes. Programming is now complete.

1. Prepare Vehicle for Programming

   ENTER the vehicle and CLOSE the Driver’s Door.
2. Confirm First Programmed Key – Step 1

   INSERT the first previously programmed transponder key into the ignition.

3. Confirm First Programmed Key – Step 2

   TURN the ignition from Position 1 (LOCK/OFF) to Position 3 (RUN). KEEP the ignition in Position 3 (RUN) for at least 3 seconds, but no more than 10 seconds.
4. Confirm First Programmed Key – Step 3

   TURN the ignition to Position 1 (LOCK/OFF) and REMOVE the first key from the ignition.

5. Confirm Second Programmed Key – Step 1

   Within 10 seconds of turning the ignition to Position 1 (LOCK/OFF), INSERT the second previously programmed key into the ignition.
6. Confirm Second Programmed Key – Step 2

   TURN the ignition from Position 1 (LOCK/OFF) to Position 3 (RUN). KEEP the ignition in Position 3 (RUN) for at least 3 seconds, but no more than 10 seconds.

7. Confirm Second Programmed Key – Step 3

   TURN the ignition to Position 1 (LOCK/OFF) and REMOVE the second key from the ignition.
8. Program New Remote Head Key – Step 1

   Within 20 seconds of turning the ignition to Position 1 (LOCK/OFF) and removing the second key, INSERT the NEW un-programmed key into the ignition.

9. Program New Remote Head Key – Step 2

   TURN the ignition from Position 1 (LOCK/OFF) to Position 3 (RUN). KEEP the ignition in Position 3 (RUN) for at least 6 seconds.
10. Exit Programming Mode

    REMOVE the NEW key from the ignition.

    If the key was successfully programmed, the theft indicator light will illuminate for 3 seconds and then go out to indicate successful programming of the key.

    If the key was NOT successfully programmed, the theft indicator light will FLASH on and off. Wait 20 seconds and repeat the process from Step 1.

11. Test Remotes

    TEST all remotes. Programming is complete.

1. Confirm First Programmed Key – Step 1

   INSERT the first previously programmed transponder key into the ignition.

2. Confirm First Programmed Key – Step 2

   TURN the ignition from OFF to ON. KEEP the ignition ON for at least 3 seconds, but no more than 10 seconds.
3. Confirm First Programmed Key – Step 3

   TURN the ignition OFF and REMOVE the first key from the ignition.

4. Confirm Second Programmed Key – Step 1

   After 3 seconds, but within 10 seconds of turning the ignition OFF, INSERT the second previously programmed key into the ignition.
5. Confirm Second Programmed Key – Step 2

   TURN the ignition from OFF to ON. KEEP the ignition ON for at least 3 seconds, but no more than 10 seconds.

6. Confirm Second Programmed Key – Step 3

   TURN the ignition OFF and REMOVE the second key from the ignition.
7. Program New Flip Key – Step 1

   After 3 seconds but within 10 seconds of turning the ignition OFF and removing the second key, INSERT the NEW un-programmed key into the ignition.

8. Program New Flip Key – Step 2

   TURN the ignition from OFF to ON. KEEP the ignition ON for at least 6 seconds.
9. Exit Programming Mode

   REMOVE the NEW key from the ignition.

   If the key was successfully programmed, it will operate the remote entry system and start the vehicle’s engine.

   If the key was NOT successfully programmed, it will NOT work the remote entry system or start the vehicle’s engine. Wait 20 seconds and repeat the process from Step 1.

10. Test Remotes

    TEST all remotes. Programming is complete.

Important:

• Verify the following prior to following these instructions:
  • Your vehicle is equipped with keyless entry, and
  • You have a key fob remote that is compatible with your vehicle.
• You MUST have 2 working smart keys (keys that start your vehicle) in order to perform this programming procedure without the assistance of a professional.
• A MAXIMUM of 4 smart keys can be programmed to your vehicle. If you’ve had 4 programmed in the past, seek the assistance of a professional programmer.
• Ensure that the vehicle is OFF prior to beginning this procedure. CLOSE all doors prior to beginning this procedure.
• You MUST perform ALL steps within 30 seconds of starting the programming procedure.
• You MUST wait 60 seconds before repeating the procedure after an unsuccessful attempt.

Note: If your vehicle cannot enter programming mode, then you cannot program any remote.  This indicates either no keyless entry installed on the vehicle or a defective keyless entry receiver module.