Chevrolet TPMS Reset/ Relearn Instruction Manual

CHEVROLET TPMS RESET

Instruction on How to reset and relearn the TPMS on Chevy Cars.

CHEVY TPMS INSTRUCTION

Chevy TPMS Reset Instruction 1

A relearn magnet, or another properly formatted TPMS scan tool, is required to perform this procedure.

Relearn Procedure.

1. Inflate all tires to pressure listed on the placard.
2. Make sure the vehicle has been in park for at least 2 minutes before proceeding.
3. Turn ignition to the ON/RUN position with the engine OFF.
4. Press the RESET button on the Driver Information Center (DIC) to clear any warning messages displayed on the Instrument Panel Cluster (IPC).
5. Press and release the OPTIONS button, on the DIC, until the IPC display is blank.
6. Press and hold the RESET button, on the DIC, for three seconds.
7. Press and release the OPTIONS button again until the message TIRE TRAINING appears on the IPC.
8. Press and release the RESET button until the message LEARN L FRONT TIRE is displayed.
9. Starting at left front tire, place the relearn magnet over valve stem until the horn sounds.
10. After the horn chirp has sounded, proceed as in step 9 for the next three sensors in the following order: RF, RR, and LR. The horn will sound after each activation. After activating the LR sensor, the horn will sound twice signifying the relearn is complete.
11. Turn the ignition switch to OFF and exit the relearn mode.

Learn More👉 2005-2019 Lexus TPMS Reset Instruction

Chevy TPMS Reset Instruction 2

Note: TPMS Scan Tool is Necessary when Relearning the TPMS of this Model.

Sensor Relearn Procedure:

1. Set the parking brake.
2. Turn ignition to the ON/RUN position with the engine OFF (not the ACC position). Note: on vehicles with PUSH-BUTTON START, press and hold the push button start until the vehicle is in ACCESSORY MODE.
3. Press the MENU button, located on the turn signal lever (or the instrument cluster on some models), until VEHICLE INFORMATION MENU is displayed in the Driver Information Center (DIC).
4. Once you are in the VEHICLE INFORMATION MENU, use the ∧∨ (on the turn signal lever) to scroll to the Tire Pressures screen.
5. Press the SET/CLR button, located at the end of the turn signal lever, to begin the sensor matching (relearn) process. A message asking if you are sure you want to relearn should display.
6. Press the SET/CLR button again to confirm the selection. The horn should sound twice signaling the car is in relearn mode.
7. Select the vehicle make, model and model year in your TPMS Scan tool.
8. Starting with the LF tire, use your Pro+ Tool to scan each sensor in the following order: LF, RF, RR and LR. The horn will chirp, after the vehicle has received a signal from each sensor. After activating the LR tire, the horn will chirp twice signifying the relearn is complete.
9. Turn the ignition to the OFF position.
10. Inflate all tires to the pressure listed on the placard.

Chevy TPMS Reset Instruction 3

Note: TPMS Scan Tool is Necessary when Relearning the TPMS of this Model.

Sensor Relearn Procedure:

1. Inflate all tires to the pressure listed on the placard.
2. Turn ignition to the ON/RUN position with the engine OFF (not the ACCposition) and lower the driver’s side window.
3. Scroll to the Tire Pressures screen, using the steering wheel buttons, then holddown the checkmark button until the horn sounds.
4. Starting with the LF tire, use your TPMS scan tool to scan each sensor in the following order: LF, RF, RR and LR. The horn will chirp, after the vehicle has received a signal from each sensor. After activating the LR tire, the horn will chirp twice signifying the relearn is complete.
5. Turn the ignition to the OFF position.

Sensor Relearn Procedure (select models):

1. Inflate all tires to the pressure listed on the placard.
2. Turn ignition to the ON/RUN position with the engine OFF (not the ACC position) and lower the driver’s side window.
3. Press and release the trip odometer button to scroll to the Tire Pressure display.
4. Hold down the trip odometer button for 5 seconds, then press the button again to confirm.
5. Starting with the LF tire, use your TPMS scan tool to scan each sensor in the following order: LF, RF, RR and LR. The horn will chirp, after the vehicle has received a signal from each sensor. After activating the LR tire, the horn will chirp twice signifying the relearn is complete.
6. Turn the ignition to the OFF position.

Chevy TPMS Reset Instruction 4

Note: TPMS Scan Tool is Necessary when Relearning the TPMS of this Model.

Procedure using another Properly Formatted TPMS Scan Tool

1. Inflate all tires to the pressure listed on the placard.
2. Turn ignition to the ON/RUN position with the engine OFF (not the ACC position).
3. Turn the headlight switch from OFF to parking lamps 4 times within five seconds. The horn sounds twice to signal the receiver is in relearn mode.
4. Starting with the LF tire, use a properly formatted TPMS scan tool to scan each sensor in the following order: LF, RF, RR and LR. The horn will chirp, after the vehicle has received a signal from each sensor. After activating the LR tire, the horn will chirp twice signifying the relearn is complete.
5. Turn the ignition to the OFF position.

Relearn Procedure for Models Equipped with a Driver’s Information Center (DIC):

1. Inflate all tires to the pressure listed on the placard.
2. Turn ignition to the ON/RUN position with the engine OFF (not the ACC position) and lower the driver’s side window.
3. Press the Vehicle Information button (located to the left or right of the instrument cluster) repeatedly until “LEARN TIRE PRESSURES” is displayed. Then press the checkmark button.
4. Starting with the LF tire, use a properly formatted TPMS scan tool to scan each sensor in the following order: LF, RF, RR and LR. The horn will chirp, after the vehicle has received a signal from each sensor. After activating the LR tire, the horn will chirp twice signifying the relearn is complete.
5. Turn the ignition to the OFF position.

Chevy TPMS Reset Instruction 5

Note: TPMS Scan Tool is Necessary when Relearning the TPMS of this Model.

Procedure using another Properly Formatted TPMS Scan Tool

Relearn Procedure for Models Equipped with Keyless Entry:

1. Inflate all tires to the pressure listed on the placard.
2. Turn ignition to the ON/RUN position with the engine OFF (not the ACCposition).
3. Using the keyless entry (key fob), press and hold the lock and the unlock buttons simultaneously until the horn sounds.
4. Starting with the LF tire, use a properly formatted TPMS scan tool to scan each sensor in the following order: LF, RF, RR and LR. The horn will chirp, after the vehicle has received a signal from each sensor. After activating the LR tire, thehorn will chirp twice signifying the relearn is complete.
5. Turn the ignition to the OFF position.

Relearn Procedure for Models Equipped with a Driver’s Information Center (DIC):

Learn More👉 BMW M-Coupe & M-Roadster 2006-2008 TPMS Reset

1. Inflate all tires to the pressure listed on the placard.
2. Turn ignition to the ON/RUN position with the engine OFF (not the ACC position) and lower the driver’s side window.
3. Press the Vehicle Information button (located to the left or right of the instrument cluster) repeatedly until “LEARN TIRE PRESSURES” is displayed. Then press the checkmark button.
4. Starting with the LF tire, use a properly formatted TPMS scan tool to scan each sensor in the following order: LF, RF, RR and LR. The horn will chirp, after the vehicle has received a signal from each sensor. After activating the LR tire, thehorn will chirp twice signifying the relearn is complete.
5. Turn the ignition to the OFF position.

Relearn Procedure for Models NOT Equipped with a Keyless Entry or DIC:

1. Inflate all tires to the pressure listed on the placard.
2. Turn ignition to the ON/RUN position with the engine OFF (not the ACC position) and lower the driver’s side window.
3. Press the trip odometer button until “LEARN TIRE PRESSURES” is displayed. Then hold down the trip odometer button until the horn chirps.
4. Starting with the LF tire, use a properly formatted TPMS scan tool to scan each sensor in the following order: LF, RF, RR and LR. The horn will chirp, after the vehicle has received a signal from each sensor. After activating the LR tire, the horn will chirp twice signifying the relearn is complete.
5. Turn the ignition to the OFF position.

Chevy TPMS Reset Instruction 6

Note: TPMS Scan Tool is Necessary when Relearning the TPMS of this Model.

Sensor Relearn Procedure with Steering Wheel Buttons:

1.Ensure all tires are inflated to the pressures listed on the tire placard.

2.Turn the ignition switch to the ON position (engine off) and lower the driver side window.

3.Scroll to the Tire Pressure screen using the steering wheel buttons then hold down the checkmark button until the horn sounds.

4.Starting with the LF tire, use a properly formatted TPMS scan tool to scan each sensor in the following order: LF, RF, RR and LR. The horn will chirp, after the vehicle has received a signal from each sensor.After activating the LR tire, the horn will chirp twice signifying the relearn is complete.

5.Turn ignition to the OFF position.

Sensor Relearn Procedure not equipped with Steering Wheel Buttons:

1.Ensure all tires are inflated to the pressures listed on the tire placard.

2.Turn the ignition switch to the ON position (engine off) and lower the driver side window. 3.Press and release the trip odometer button to scroll to the Tire Pressure display.

4.Hold down the trip odometer button for five seconds then press the button again to confirm.

5.Starting with the LF tire, use a properly formatted TPMS scan toolto scan each sensor in the following order: LF, RF, RR and LR. The horn will chirp, after the vehicle has received a signal from each sensor.After activating the LR tire, the horn will chirp twice signifying the relearn is complete.

6.Turn ignition to the OFF position.

Chevy TPMS Reset Instruction 7

Note: TPMS Scan Tool is Necessary when Relearning the TPMS of this Model.

Sensor Relearn Procedure with Steering Wheel Buttons:

1.Ensure all tires are inflated to the pressures listed on the tire placard. 2.Turn the ignition switch to the ON position (engine off) and lower the driver side window.

3.Scroll to the Tire Pressure screen using the scroll wheel on the turn signal stalk.

4.Scroll to the Tire Pressure Menu usion the scroll wheel, located to the left of the MENU button and hold down the SET/CLR button (located at the end of the turn signal stalk.

5.Using the scroll wheel, scroll to “Yes” and press the SET/CLR button again. The Horn will chirp.

6.Starting with the LF tire, use your Pro+ Tool to scan each sensor in the following order: LF, RF, RR and LR. The horn will chirp, after the vehicle has received a signal from each sensor. After activating the LR tire, the horn will chirp twice signifying the relearn is complete.

7.Turn ignition to the OFF position.

Chevy TPMS Reset Instruction 8

Note: TPMS Scan Tool is Necessary when Relearning the TPMS of this Model.

Sensor Relearn Procedure with Steering Wheel Buttons:

1.Ensure all tires are inflated to the pressures listed on the tire placard.

2.Start the Vehicle.

3.Using the streering wheel’s keypad, select “Settings,””Display Options,” then “Tire Pressure” to turn on the Tire Pressure readout display”

4.Exit the “Settings” menu and scroll to the Tire Pressure Screen.

5.Hold down the SEL/Checkmark button until the horn sounds twice.

7.Shut the vehicle off.

Chevy TPMS Reset Instruction 9

Note: TPMS Scan Tool is Necessary when Relearning the TPMS of this Model.

Relearn Procedure with Steering Wheel Buttons:

1.Ensure all tires are inflated to the pressures listed on the tire placard.

Learn More👉 HOW TO GUIDE: Honda Civic Tire Pressure TPMS Light Reset

2.Set the Parking Brake

3.With the vehicle off, hold down the ignition button for 5 seconds

Do not press the brake pedal while holding downt he ignition button.

4.Using the streering wheel’s keypad, select “Settings,””Display Options,” then “Tire Pressure” to turn on the Tire Pressure readout display”

5.Exit the “Settings” menu and scroll to the Tire Pressure Screen.

6.Hold down the SEL/Checkmark/ or scroll‐wheel until the horn sounds twice.

7.Starting with the LF tire, use your Pro+ Tool to scan each sensor in the following order: LF, RF, RR and LR. The horn will chirp, after the vehicle has received a signal from each sensor. After activating the LR tire, the horn will chirp twice signifying the relearn is complete.

8.Shut the vehicle off.

Chevy TPMS Reset Instruction 10

Note: TPMS Scan Tool is Necessary when Relearning the TPMS of this Model.

Sensor Relearn Procedure for Gas Fueled Models:

1.Ensure all tires are inflated to the pressures listed on the tire placard.

2.Place ignition into the ON position (engine OFF)

3.There are two options listed below.

A.Press the MENU button, located to the right of the gauge cluster, and select “MENU 2”. If “MENU 2” is not option, go to step 4
B. Press the “MENU” button to select the Vehicle Info Menu.

4.There are two options listed below.

A.Using the arrow buttons, scroll to the “Tire Learn” menu.
B.Scroll to the “Tire Learn” or “Tire Pressure” menu using the scroll wheel on the turn signal lever.
C.Press and hold the SET/CLR button, and if prompted, select “YES” to confirm by pressing the SET/CLR button.

5.Starting with the LF tire, use your TPMS Scan Tool to scan each sensor in the following order: LF, RF, RR and LR. The horn will chirp, after the vehicle has received a signal from each sensor. After activating the LR tire, the horn will chirp twice signifying the relearn is complete.
6.Shut the vehicle off.

Sensor Relearn Procedure for Electric Models:

1.Ensure all tires are inflated to the pressures listed on the tire placard.
2.Place ignition into the ON position (engine OFF)

3.Navigate to the Driver Info display by pressing the SELECT knob on the steering wheel.

4.Scroll to the Tire Pressure screen and press down the SELECT knob for 5 seconds.

5.If prompted, scroll over to confirm “YES” and press the SELECT knob again.

6.Starting with the LF tire, use your TPMS Scan Tool to scan each sensor in the following order: LF, RF, RR and LR. The horn will chirp, after the vehicle has received a signal from each sensor. After activating the LR tire, the horn will chirp twice signifying the relearn is complete.

7.Shut the vehicle off.

Chevy TPMS Reset Instruction 11

Note: TPMS Scan Tool is Necessary when Relearning the TPMS of this Model.

Sensor Relearn Procedurewith Steering Wheel Buttons:

1.Ensure all tires are inflated to the pressures listed on the tire placard.

2.Turn the ignition switch to the ON position (engine off) and lower the driver side window.

3.Scroll to the Tire Pressure screen using the steering wheel buttons then hold down the center scroll wheel until the horn sounds.

4.Select the vehicle make, model and model year in your Pro+ Tool.

5.Starting with the LF tire, use your TPMS Scan Tool to scan each sensor in the following order: LF, RF, RR and LR. The horn will chirp, after the vehicle has received a signal from each sensor.After activating the LR tire, the horn will chirp twice signifying the relearn is complete.

6.Turn ignition to the OFF position.

Sensor Relearn Procedurewithout Steering Wheel Buttons:

1.Ensure all tires are inflated to the pressures listed on the tire placard.

2.Turn the ignition switch to the ON position (engine off) and lower the driver side window.

3.Press and release the trip odometer button to scroll to the Tire Pressure display.

4.Hold down the trip odometer button for five seconds then press the button again to confirm.

5.Select the vehicle make, model and model year in your TPMS Scan Tool.

6.Starting with the LF tire, use your Pro+ Tool to scan each sensor in the following order: LF, RF, RR and LR. The horn will chirp, after the vehicle has received a signal from each sensor.After activating the LR tire, the horn will chirp twice signifying the relearn is complete.

7.Turn ignition to the OFF position.

Chevy TPMS Reset Instruction 12

Dealer Relearn Currently, only the Original Equipment (OE) Dealership has the scan tool necessary to register new sensor IDs.

Chevy TPMS Reset Instruction 13

No special tools are required to perform this relearn procedure.

Sensor Relearn Procedure:

1.Inflate all tires to pressure listed on the placard.

2.Vehicle must sit stationary (engine off) for 20 minutes before the system recalculates.

3.Drive the vehicle for at least 10 minutes at a speed of 15 MPH, or more. All sensor IDs will be memorized automatically.

Note: a warning message will be displayed in the Driver Information Center (DIC) if a problem occurs during the relearn process.